H7182 IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. www.fisher-price.co.
Consumer Information IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach. WARNING • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool needed for assembly: Phillips screwdriver (not included). • Requires three "AA" (LR6) alkaline batteries for electronic toy operation (not included). • Product features and decorations may vary from illustrations.
Parts Seat Back Pad 2 Frames Seat Bottom Footrest Back Base Front Base 2 Seat Bottom Tubes Food Tray Hinge Rod Toy Bar Base Tray 2 Teether Toys Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. 3 Plastic Rings • Align the holes in the plastic rings and the seat bottom tubes.
Assembly Insert Screws Here Hinge Hinge Rod 4 6 • Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom.Tighten the screws.This may require extra force. Seat Back Pin Slot • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 9.
Assembly Frame Leg 4 Seat Height Adjusters Position 4 Frame Decorated Side Press Lever Frame Back Legs 8 • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Back Base Seat Assembly Screw Retainers Sockets Sockets 7 • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. • Position a frame so that the decorated side is outward. • Fit the end of the back base into the back leg of a frame.
Assembly Push Screw Retainers Push Seat Bottom Tube Ends Front Base 10 11 • Insert the frame front legs onto the front base. • Fit a screw retainer over a hole in the front leg. • Insert a #10 x 2,2 cm black screw through the screw retainer and front leg.Tighten the screw. • Repeat this procedure to secure the other end of the front base with the remaining screw retainer and #10 x 2,2 cm black screw. Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers.
Assembly Pad Seat Height Adjuster Seat Height Adjuster Elastic Loops Seat Bottom Tube Ends Hole Hole 12 • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube.Tighten the screws.This may require extra force. Tabs Elastic Loops 13 • Lift the assembly upright. • From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad.
Assembly Slot Crotch Belt 14 Bottom Slots • Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted. 16 Shoulder Portion • Lift the top of the pad. • Thread the waist/shoulder belts through the bottom slots in the back of the seat pad. 15 • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back.
Assembly • From behind the seat, be sure the shoulder portion of the waist/shoulder belts are secure in the seat back slots. • Fit the pad strap through the handle and press it to the fastener on the back of the seat. • Hook the elastic loops on each side of the pad onto the tabs in the seat back. Upper Shoulder Belt Slots Shoulder Portion Toy Bar 19 • Insert and “snap” the toy bar into the electronic toy, as shown.
Battery Installation Secure Child 1,5V x 3 "AA" (LR6) WARNING Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Battery Compartment Waist/Shoulder Belt Waist/Shoulder Belt Crotch Belt • Loosen the screws in the battery compartment. Remove the battery compartment door. • Insert three “AA” (LR6) alkaline batteries.
Secure Child Anchored End Anchored End A B Free End Buckle 2 B A Tighten Free End Loosen To tighten the waist belts: • Feed the anchored end of the waist belt up through the buckle to form a loop A . • Pull the free end of the waist belt B . • Repeat this procedure to tighten the other waist belt. To loosen the waist belts: • Feed the free end of the waist belt up through the buckle to form a loop A . • Enlarge the loop by pulling on the end of the loop toward the buckle.
Using the Trays and Toys WARNING Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Base Tray 7 Armrest • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward . • While squeezing the latches underneath the base tray, adjust the base tray forward or backward .
Using the Trays and Toys Electronic Toy Food Tray Button Tab Base Tray Groove 11 9 Base Tray • Insert the tab on the edge of the electronic toy into the groove in the front of the base tray. • Push the electronic toy down to secure in place. Hint: The electronic toy does not fit into the food tray. • To remove the electronic toy, press the button on the front of the electronic toy. Remove the electronic toy. • Fit the food tray into the base tray, as shown.
Adjusting the Seat Brakes WARNING WARNING Prevent serious injury or death from falls or sliding out. It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position. Prevent serious injury or death from falls or sliding out. • Always leave wheels locked. • Never use near steps. Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline.
Storage Care Pull Frame Release Latch • The pad, restraint system, frame base tray and electronic toy may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the electronic toy. • The food tray and teether toy are also top rack dishwasher safe (or use bottom rack - without using the drying cycle). To remove the pad: • Remove the elastic loops from the pegs on the back of the seat.