Product features and decorations may vary from photo above. Instructions Model Number: H7182 WARNING IMPORTANT! KEEP FOR FUTURE REFERENCE. Please read these instructions before assembly and use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Requires three “AA” (LR6) alkaline batteries for toy operation (not included). www.fisher-price.
Warning and Caution WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. • Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. CAUTION This product contains small parts in its unassembled state.
Parts Food Tray Electronic Toy Pad Toy Bar 2 Teether Toys Base Tray Seat Back Hinge Rod #10 x 2.2 cm Black Screw Frame Frame Seat Bottom 2 Seat Bottom Tubes #8 x 1.9 cm Screws - 4 #8 x 1.9 cm Screws - 2 #10 x 2.2 cm Black Screws - 2 2 Screw Retainers #8 x 1.9 cm Screws - 2 Back Base #10 x 2.2 cm Black Screws - 2 Footrest Screw Retainer Screw Retainer Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Front Base #10 x 2.
Assembly IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Plastic Rings Seat Bottom Tubes Toy Bar 3 Plastic Rings • Slide a seat bottom tube through each set of plastic rings on the seat bottom. 1 Electronic Toy Plastic Rings • Insert and “snap” the toy bar into the electronic toy, as shown.
Assembly Footrest Insert Screws Here Hinge Hinge Rod 5 7 #10 x 2.2 cm Black Screw - 2 • Insert two #10 x 2.2 cm black screws through the footrest and into the seat bottom. Tighten the screws. Seat Back Pin #10 x 2.2 cm Black Screw • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 9.
Assembly Seat Height Adjusters Frame Decorated Side Position 4 Frame Back Legs Press Lever Back Base Hole 10 • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Screw Retainers Seat Assembly Back Base Hole 9 Screw Retainer - 2 #10 x 2.2 cm Black Screw - 2 Sockets • • • • Position a frame so that the decorated side is outward. Insert the back leg of a frame into the back base.
Assembly #10 x 2.2 cm Black Screw - 2 Screw Retainer - 2 Push Seat Height Adjuster Push Seat Height Adjuster Front Leg Holes Screw Retainers Seat Bottom Tube Ends 12 13 #8 x 1.9 cm Screw - 2 • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1.9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. • Insert the frame front legs onto the front base.
Assembly Pad Seat Height Adjusters #8 x 1.9 cm Screw - 2 Elastic Loops Hole Hole Front View Seat Bottom Tube Ends 14 Back and Bottom View Tabs • From the back and bottom of the assembly, insert a #8 x 1.9 cm screw through both seat height adjusters and the ends of the seat bottom tube. Tighten the screws. Elastic Loops 15 Back and Bottom View • Lift the assembly upright. • From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad.
Assembly Upper Shoulder Belt Slots Shoulder Portion Lower Shoulder Belt Slots 18 Slot Crotch Belt 16 Shoulder Portion • Fit the top of the pad over the seat back. • Fold the bottom edge of the pad under the edge of the seat bottom to fasten it. • Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back. Use the lower shoulder belt slots for a smaller baby. Use the upper shoulder belt slots for a larger baby.
Battery Installation Batteries may leak fluids that can cause a chemical burn injury or ruin our product. To avoid battery leakage: 1.5V x 3 "AA" (LR6) • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely.
Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child’s reach. Anchored End Buckle A B WARNING Free End Prevent serious injury or death from falls or sliding out.
Securing Your Child Hold Adjuster Shoulder Portion Pull Strap Down Slide Adjuster Down 6 4 Tighten • From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad and the seat back. Pull on the belts to be sure they are secure in the seat back. Loosen • To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down.
Using the Trays and Toys WARNING Base Tray Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. 8 Release Bar Hint: The base tray can be adjusted for your child’s comfort two ways (see steps 8 and 9)! • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward.
Using the Trays and Toys Electronic Toy Button Base Tray Tab Release Bar 11 Groove • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. 14 Base Tray Food Tray • Insert the tab on the edge of the electronic toy into the groove in the front of the base tray. • Push the electronic toy down to secure in place. Hint: The electronic toy does not fit into the food tray.
Adjusting the Seat Storage WARNING WARNING Prevent serious injury or death from falls or sliding out. • Always leave wheels locked. • Never use near steps. Prevent serious injury or death from falls or sliding out. It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. Press Tab Lift Tab Seat Height Adjuster 18 TO LOCK: Press the tab down until you hear a "snap". TO UNLOCK: Lift the tab up.
Storage Storage Electronic Toy Tab Base Tray Hole Peg 19 21 • Fit the holes on the base tray latches onto the pegs on the back of the high chair frame. • Fit the electronic toy to the tab on the back of the high chair, as shown. Care Pull Frame Release Latch 20 • With the legs all the way open, lower the seat to position 7 the lowest position). • Pull the frame release latches forward and push the rear legs toward the front legs. Fisher-Price, Inc., a subsidiary of Mattel, Inc.