www.fisher-price.com H7181 Product features and decorations may vary from picture above. WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool needed for assembly: Phillips Screwdriver (not included). • Requires four “C” (LR14) alkaline batteries for operation (not included). • Weight Limit: 9 kg (20 lbs). IMPORTANT! The maximum weight limit for this product is 9 kg (20 lbs).
Parts WARNING To prevent serious injury or death from falls and being strangled in the restraint system: • Always use the restraint system. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg, 20 lbs). • Never leave the child unattended. • It is dangerous to use this product on an elevated surface. Seat Back Tube Pad Lower Swing Arm Assembly (with Restraint System) CAUTION Frame This package contains small parts in its unassembled state.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Press Button on Front Tube Press Button on Lower Frame Tube Upper Frame Tube 3 1 Rubber Feet Down • Position the front tube so that the rubber feet are flat on � the surface.
Assembly Frame Upper Frame Tube Upper Frame Tube Front Tube 4 • Pull the front tube to be sure it is secure to each lower frame tube. 6 • Check to be sure the upper frame tubes are secure in the frame. If you can remove the upper frame tubes from the frame, you have not properly inserted the tubes into the frame. Repeat Assembly step 5. Frame Press Button on Upper Frame Tube 5 • Insert the upper frame tubes into the frame until you hear a "click" on both sides.
Assembly Seat Back Tube Upper Swing Arms 7 Buttons Lower Swing Arm Assembly (with Restraint System) 9 • Fit the lower swing arm assembly to the outside of each upper swing arm. Swing Arm Short Tubes • Position the seat back tube so that it curves toward the back of the swing. • While pressing the buttons on the seat back tube, fit the seat back tube into the short tubes on the swing arms. • Push the seat back tube until it “clicks” into place.
Assembly Upper Pocket Slot Slot Fastener Lower Pocket Waist Belts B 10 Seat Back Tube Seat Bottom Tube • Fit the upper pocket on the pad over the seat back tube . • Lift the seat bottom tube. Fit the lower pocket on the pad over the seat bottom tube B . 11 • From behind the seat, insert the waist belts into the slots in the pad. • Push to fasten the restraint system to the pad. Assembly is now complete.
Battery Installation Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely.
Setup and Use WARNING To prevent serious injury or death from falls and being strangled in the restraint system: • Always use the restraint system. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg (20 lbs). • Never leave the child unattended. • It is dangerous to use this product on an elevated surface. Waist Belt Crotch Pad IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
Setup and Use Anchored End Anchored End POWER DIAL Free End 2 TIGHTEN Power Dial Free End LOOSEN To tighten the restraint straps: • Feed the anchored end of the restraint strap up through the buckle to form a loop . Pull the free end of the restraint strap . To loosen the restraint straps: • Feed the free end of the restraint strap up through the buckle to form a loop . Enlarge the loop by pulling on the end of the loop toward the buckle.
Setup and Use Baby Activated 5 Lights and Music Switch Parent Activated Volume Dial Lights and Music Switch Hint: Your baby can enjoy lights and music with or without swinging. • Slide the lights and music switch to: When baby pulls either toy on the arch, one tune plays along with twinkling lights. On this setting, six tunes (approximately 10 minutes) play along with dancing lights. On this setting, music plays for about 10 minutes. Turns lights and music off.
Take-Along Lower Frame Tube Lift Seat Bottom Lift Seat Back 1 • Lift the seat back and seat bottom together. Seat Back 3 • Rotate the lower frame tube around to the top of frame, as shown. To set the swing back up for use: • Rotate the lower frame tube around until it snaps into place. • Place the swing on a non-elevated, flat surface. 2 Press Buttons • Tip the swing backwards with the seat back down. • Press both buttons on the frame at the same time to release the frame base.
Care Consumer Information GREAT BRITAIN Helpline: 01628 500302. Or write to: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. • The frame, pad and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the frame. • This product has no consumer serviceable parts. Do not take this product apart. IMPORTANT! Never use this product without the provided pad. Be sure to re-attach the provided pad (with restraint system) to this product. AUSTRALIA Mattel Australia Pty.