Scan it. Watch it. Build it. fisher-price.
WARNING: Prevent serious injury or death: • Never leave child unattended. • This product is not intended for unsupervised or prolonged periods of sleep. • Always use the restraint system. • Never use for a child able to sit up unassisted. • Fall Hazard – Never use on any elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard – Never use on a soft surface (bed, crib, sofa, cushion) since the product can tip over and cause suffocation.
BEFORE YOU BEGIN IMPORTANT! Keep this instruction sheet for future reference, as it contains important information. Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Do not use the product if any parts are missing, damaged or broken. Do not use accessories or replacement parts other than those approved by the manufacturer. Never substitute parts. Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included).
PARTS IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. We recommend installing batteries in the soothing unit before beginning assembly.
PARTS x8 M3,5 x 15 mm Screw Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
ASSEMBLY Push the base tube until it “snaps” into place. Pull on it to be sure it’s assembled to the base. 1 Oh, no! If you snapped one end of the base tube into the base and can’t assemble the other end, you can remove the base tube. See the next step for instructions to remove the base tube. 2 Rotate the tube up and then pull it out. Go back to assembly step 1.
ASSEMBLY Push the other base tube until it “snaps” into place. Pull on it to be sure it’s assembled to the base. 4 During shipping, the seat base tubes may have moved. Press the latch and make sure the ends of the tubes align on both sides. 5 If the seat back does not snap to the tubes, try assembling it to the tubes on the opposite side of the seat base. It’s easier to complete assembly if the seat base tubes are turned.
ASSEMBLY 7 Make sure the socket is upright. 8 Make sure the socket is upright.
ASSEMBLY Turn the assembly over and fit a seat rail to the frame.
ASSEMBLY 12 x4 13 10
ASSEMBLY Hint: Before attaching the seat pad in the next step, you may want to install the soother battery. Go to page 13 for battery installation instructions. Turn the assembly upright to attach the seat pad. Attach the pad around the soother.
ASSEMBLY Fasten the pad button holes to the pegs. 16 Buckle the straps on the pad. Make sure you hear a “click”. 17 Tuck the pad around the toy bar retainers.
ASSEMBLY Fit the restraint belts through the slots in the body support. 19 SOOTHER BATTERY INSTALLATION The battery compartment is located on the underside of the soother. Remove the seat pad from around the soother. Loosen the screw in the battery compartment door and lift to remove the door. Insert one D (LR20) alkaline battery. Replace the battery compartment door and tighten the screw. Replace the seat pad around the soother.
ADJUST SEAT BACK The seat back can be raised or lowered for upright or recline seating when used as a rocker or glider. Press the latch on the seat frame and then push the seat back or the seat bottom into upright or recline positions. TOY BAR The toy bar is removable. Simply press the the ends of the latches and lift the toy bar.
GLIDER “Snap” the seat to the base to use as a glider. 1 Place the glider near a standard wall outlet. First plug the AC adapter into the glider base and then the wall outlet. Use the AC adapter only in a wall outlet. Do not plug the adapter into a ceiling outlet.
PAIRING YOUR DEVICE Before using the Smart Connect™ app for the first time, you will need to pair your device with the glider. Open the Smart Connect™ app on your device. Be sure your device is within approximately 1,8 m (6 ft) of the glider to pair. Press and hold the pairing button (power button) on the glider control panel for about 5 seconds. The glider stays in pairing mode for approximately 30 seconds. Hint: If you cannot pair your device with the glider, try moving the device closer to the glider.
SMART CONNECT™ APP App features and decorations shown in photographs and illustrations may vary. Touch to customize the glider name. Touch to connect or disconnect your device from the glider. Touch to start selections (gliding, sounds or music). Touch again to pause. Touch to decrease gliding speed. Touch to increase gliding speed. Choose the amount of gliding time. Touch to start settling music that transitions to calming music. Make sure you choose the amount of time for each stage.
RESTRAINT SYSTEM Position the restraint pad between your child’s legs and fasten the restraint belts to each side of the restraint pad. Make sure you hear a “click” on both sides. Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached. Tighten each waist belt so that the restraint system is snug against your child. 1 To tighten: Feed the attached end of the restraint belt into the buckle to form a loop.
GLIDER Touch the power button on the glider base to turn power ON or OFF. Touch the speed buttons or to select the desired gliding speed or to turn gliding motion off. or for music or nature sounds. Touch Touch the same button again and again to cycle through music or sounds or to turn music or sounds off. Touch or to adjust volume up or down. If the glider begins to operate erratically, you may need to reset the electronics. Unplug the AC adapter from the glider base and then plug back in again.
ROCKER SEAT Lift to remove the seat from the base to use as a rocker. SOOTHING VIBRATIONS Slide the soother power switch to turn vibrations ON or OFF. Low battery power or a static charge may cause the soother to operate erratically. If vibration does not turn on or will not turn off, remove and reinstall the battery. If you still experience a problem, replace the battery.
WANT TO SWITCH THE MOTION? Turn the seat for head-to-toe motion. 1 HEAD-TO-TOE Turn the seat for side-to-side motion.
CARE AC POWER USE The seat pad and body support are machine washable. Wash them separately, with a mild detergent, in cold water and on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. To remove the pad, unfasten the rear strap buckle on the pad. Pull to remove the pad from around the seat back, soothing unit and the toy bar retainers. Remove the back of the pad from the pegs on the seat back. Lift to remove. Follow the assembly instructions to re-attach the pad.
GENERAL INFORMATION FCC STATEMENT (UNITED STATES ONLY) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
UNITED STATES 1-800-432-5437. Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Hearing-impaired consumers: 1-800-382-7470. CHILE Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago. Tel.: 1230-020-6213. VENEZUELA Servicio al consumidor Venezuela: Tel.: 0-800-100-9123. ARGENTINA Mattel Argentina, S.A., Av. Libertador 1000, Piso 11 – Oficinas 109 y 111, Vicente López – Prov. Buenos Aires. Tel.: 0800-666-3373. COLOMBIA Mattel Colombia, S.A., Calle 123#7-07 P.5, Bogotá. Tel.