User Manual

ManualsBrandsFisher-Price ManualsBaby Floor SeatsSit-Me-Up Floor Seat

DRF51

fisher-price.com

Placing and Removing Baby

• Place the assembled product

on the floor.

• Kneel or stand behind the seat

and fit or remove baby’s legs

into or from the leg openings

in the seat pad. Carefully

lower or lift baby into or out

of the seat.

Sentar y sacar al bebé

• Poner el producto

ensamblado sobre el piso.

• Arrodillarse o pararse detrás

de la silla y meter o sacar

las piernas del bebé en/de

los orificios de pierna del

colchón. Sentar o sacar

cuidadosamente al bebé

en/de la silla.

Linkable, Removable Toys

• Fit the link on each toy to

a loop on the seat.

Juguetes que se pueden

conectar y quitar

• Conectar el aro de cada

juguete en una conexión en

la silla.

Summary of content (8 pages)

PAGE 1
DRF51 Linkable, Removable Toys • Fit the link on each toy to a loop on the seat. Juguetes que se pueden conectar y quitar • Conectar el aro de cada juguete en una conexión en la silla. Placing and Removing Baby • Place the assembled product on the floor. • Kneel or stand behind the seat and fit or remove baby’s legs into or from the leg openings in the seat pad. Carefully lower or lift baby into or out of the seat. Sentar y sacar al bebé • Poner el producto ensamblado sobre el piso.
PAGE 2
Care Mantenimiento • To clean the frame and toys, wipe clean using a mild cleaning solution and damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove soap residue. • Machine wash the pad in cold water on the gentle cycle. Do not use bleach. Tumble dry on low heat. • To remove the pad, lift to remove the pad pegs from the front base. Then remove the pad button holes from the pegs underneath the seat ring. • To replace the pad, follow the assembly steps.
PAGE 3
Consumer Information Información al consumidor WARNING To prevent serious injury or death: • Fall Hazard – Never use on any elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard – Never use on a soft surface (bed, sofa, cushion), since the product can tip over and cause suffocation in soft surfaces. • Never leave child unattended. Always keep child in view while in product. • Never use near steps.
PAGE 4
Assembled Parts Piezas ensambladas Front Base (2 pieces) Base delantera (2 piezas) Rear Base (2 pieces) Base trasera (2 piezas) Seat Ring Aro del asiento Pad Colchón 2 Frames 2 armazones 2 Caps 2 tapones IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Do not use the product if any parts are missing, damaged or broken. Do not use accessories or replacement parts other than those approved by the manufacturer.
PAGE 5
Assembly Montaje 1. • “Snap” the front base pieces together. 3. 3 • Ajustar las piezas de la base delantera. • “Snap” the rear base pieces together. Hub Button Out Botón de conexión hacia afuera • Ajustar las piezas de la base trasera. Hub Button Out Botón de conexión hacia afuera 4. 2. • Fit the rear base onto the ends of the frames and push to “snap” in place. • Pull on the rear base to be sure it’s attached. • Position the frames with the hub buttons facing out.
PAGE 6
Assembly Montaje PUSH EMPUJAR PUSH EMPUJAR 5. 7. • Lift the frames until each “snaps” into place. • Push the frame near a seat ring peg to “snap” the seat ring into place. Hint: If you cannot “snap” the parts into place, you may have assembled the seat ring backwards. Remove the seat ring from the frames and turn it around so that the wider, flat side is toward the front base. Then, repeat this assembly step. • Subir los armazones hasta que cada uno se ajuste en su lugar.
PAGE 7
Assembly Montaje 8. • Fit a cap onto each frame. Fit the wide tab on the cap to the wide notch in the frame and the narrow tab on the cap to the narrow notch in the frame. • Push to “snap” in place. 10. • Ajustar un tapón en cada armazón. Ajustar la lengüeta ancha del tapón en la muesca ancha del armazón y la lengüeta estrecha del tapón en la muesca estrecha del armazón. • Presionar para ajustarlos en su lugar. TOP VIEW VISTA DE ARRIBA • Pull the edge of the seat pad around the seat ring.
PAGE 8
Assembly Montaje Opening the Frame Abrir el armazón 11. • Lift the frames until each “snaps” into place. Push down on the seat ring to be sure the frame is open. • Insert and “snap” the pegs on the pad into the holes in the front base. • Your product may come with replacement warning labels which you can apply over the factory applied warning label if English is not your primary language. Select the warning label with the appropriate language for you.