User Manual

ManualsBrandsFisher-Price ManualsStacking & Sorting Toys3-in-1 Sit Stride & Ride Lion

DHW02

Keep this instruction sheet for future reference,

as it contains important information.

Requires three AA batteries (included).

Batteries included are for demonstration purposes only.

Adult assembly is required.

Tool required: Phillips screwdriver (not included).

fisher-price.com

Not to be used by children over

36 months (due to seat height).

WARNING!

Summary of content (8 pages)

PAGE 1
DHW02 WARNING! Not to be used by children over 36 months (due to seat height). Keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries (included). Batteries included are for demonstration purposes only. Adult assembly is required. Tool required: Phillips screwdriver (not included). fisher-price.
PAGE 2
Consumer Information FCC STATEMENT (UNITED STATES ONLY) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
Assembled Parts Head Seat 2 Front Wheels (Smaller) 2 Rear Wheels (Larger) Frame 2 Front Axles 2 Hubs CAUTION This package contains small parts. For adult assembly only. M4,5 x 1,9 cm Screw - 11 Shown Actual Size Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten screws.
PAGE 4
Assembly Rear Wheel (Larger) Front Axle 1 Front Wheel (Smaller) Hub • Slide a front wheel onto a front axle. 3 • Fit a rear wheel onto the rear axle. • Fit a hub into the center of the rear wheel. • Insert a screw into the center of the hub Frame and tighten. • Repeat this procedure to attach the other rear wheel and hub. Seat 2 BOTTOM VIEW • Turn the frame over and fit the front axle assembly onto the front of the frame. • Insert three screws and tighten.
PAGE 5
Assembly 5 BACK VIEW 7 • Push the back of the seat to "snap" in place. BOTTOM VIEW • While holding the head in place, turn the frame over. • Insert three screws into the holes in the frame and tighten. 6 FRONT VIEW • Fit the head onto the frame.
PAGE 6
Battery Replacement Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbonzinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batteries safely.
PAGE 7
Ready, set, GO! Press lion's nose for fun lights with phrases or music! Press a button on the lion's mane to hear its number. Press the same button again to hear its color. Press the button a third time to hear its number, then count the tones you hear! Open the lion's mouth to drop a ball in and hear more fun phrases or music! Hear phrases, music or sound effects when you push the lion. • Slide the power/volume switch: • Adult supervision is required. • Never use near steps.
PAGE 8
Rider to Walker Walker to Rider Only an adult should convert this product. Only an adult should convert this product. 1 1 2 2 3 3 • Pull out the latch on the back of the seat and • Pull out the latch on the back of the seat and lift the seat 1 . • Lift the support 2 . • Push down on the handle to "snap" it to the support 3 . Lift the handle to be sure it's secure to the support, lift the seat 1 . • Lower the support and lower the seat 2 . • Push down on the seat to "snap" in place 3 .