Deluxe Smart Response Swing ™ Product features and decorations may vary from picture above. Accessories sold separately. Model Numbers: 79644, B2388 PLEASE KEEP FOR FUTURE REFERENCE. Please read these instructions before assembly and use of this product, as they contain important information. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.
Parts 2 Front Legs (Longer) 2 Accessory Bins Housing Motor Housing 2 Rear Legs (Shorter) Pad Front Base Tray Rear Base Bracket (with M4 Lock Nuts) Mirror Base Seat with Restraint 2 Seat Wire Caps 2 Seat Tubes Sound ‘n Lights Tray Seat Wire M4 Screw - 4 Shown Actual Size #8 x 13/8" Screw - 10 Shown Actual Size #6 x 5/8" Screw - 4 Shown Actual Size Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Hub Front Legs (Longer) Housing Motor Housing Slot Tapered End Hole Press Buttons Press Button Press Button Front Legs Tapered End 1 3 Front Base • Place the front base on a flat surface.
Assembly Pull Up Pull Up Pull Rear Leg Pull Rear Leg Rear Legs 5 7 Rear Base • Pull both rear legs out until they “snap” into place. • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them correctly to the rear base. Reread and repeat assembly step 6. • Set the frame assembly aside for Assembly step 17.
Assembly M4 Lock Nut Rounded Side Bracket Grooves Shown Actual Size Lock Nut Tall End Seat Tubes Bottom Edge of Seat Hexagonal Opening 9 • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory. During shipment of this product, they may have fallen out. Check to be sure there is a lock nut in each hexagonal opening on the bracket.
Assembly Press in Place Seat Wire is Through Hole in Seat Wire Cap Seat Wire Slots Seat Wire Caps 15 13 • Press to the seat wire caps into place. • Insert two #6 x 5/8" screws through each seat wire cap and tighten. • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. #6 x 5/8" Screw - 4 Shown Actual Size Hint: The seat wire caps are designed to fit into the seat only one way.
Assembly Frame Hub Push Button Pad Swing Tube Front of Seat Waist Belts Curved Front Base 17 19 • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs. Push the swing tubes up until the buttons “snap” into the hole in the frame hubs. • Push down on the seat to be sure the seat is secured in both frame hubs. • Fit the pocket on the back of the pad onto the seat back.
Assembly Elastic Loop Elastic Loop 23 21 #8 x 13/8” Screw - 4 Shown Actual Size • Turn the assembly over. Insert four #8 x 13/8" screws into the bottom of the lights ‘n sounds tray and tighten. Assembly is now complete. • Fit the bottom edge of the pad around the bottom edge of the seat. • Hook the elastic loops on each side of the pad to the peg on the back of the accessory bins.
Battery Installation Battery Safety Information Hint: When swinging, sound or power L.E.D. slows/dims/stops, it’s time to replace the batteries! We recommend using alkaline batteries for longer battery life. 1.5V x 4 “D” (LR20) 1.5V x 3 “AA” (LR6) BOTH SHOWN ACTUAL SIZE Battery Compartment Door Batteries may leak fluids that can cause a chemical burn injury or ruin your product.
Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. WARNING Anchored End Anchored End A • To prevent serious injury or death from falls and being strangled in the restraint system: - Always use the restraint system. Never rely on the tray to restrain child.
Swing Modes Adjusting the Seat The Smart Response Swing has two modes: Baby Sounds Activated and Parent Activated . Upright 3 Semi-Recline Recline Baby Sounds Activated Adjust the seat angle in any of three positions: Upright, Semi-Recline or Recline. To adjust the seat angle: Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright, Semi-Recline or Recline.
Baby Sounds Activated Speed Dial Sound Sensitivity Dial Power L.E.D. Swing Mode Switch Music/Volume Switch Sound Sensitivity Dial • Slide the switch to high sensitivity for incoming sounds (listens for shallow sounds). • Slide the switch to low sensitivity for incoming sounds (listens only for loud sounds). Hint: You may want to start with the high sensitivity setting at first. Music/Volume Switch • Select for music highest volume. • Select for music high volume. • Select for music low volume.
Parent Activated Power L.E.D. Swing Mode Switch Speed Dial Music/Volume Switch Swing Mode Switch • Slide the switch to parent activated. The power L.E.D. lights and the swing begins swinging. • Be sure to turn the product off when not in use. Speed Dial • Select any of five speed settings. Music/Volume Switch • Select for music highest volume. • Select for music high volume. • Select for music low volume. • Select to turn music off.
Sound ‘n Lights Tray Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, tray and sound ‘n lights tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the sound ‘n lights tray. Cat Bar Dog Sound ‘n Lights Tray Upper Pad Pocket Elastic Loops Tray Lower Pad Pocket Elastic Loops • Fit the sound ‘n lights tray to the tray, as shown.
One (1) Year Limited Warranty FCC Statement (United States Only) Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants that Deluxe Smart Response™ Swing is free from all defects in material and workmanship when used under normal conditions for a period of one (1) year from the date of purchase. Should the product fail to perform properly, we will repair or replace it at our option, free of charge.