Cover’n Play ™ Bouncer Model Number: 79619 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tool required for assembly: Phillips Screwdriver (not included). Requires one “D” (LR20) alkaline battery (not included). c e. -pri r e h f is www.
Warning WARNING To prevent serious injury and/or falls: • Never use on any elevated surface, since child’s movement may cause bouncer to slide or tip over. • Never use as a carrier or lift while child is seated. • Always use the restraint system. • Never leave child unattended. • Never use as a car seat. • Never use with a child able to sit up unassisted.
Parts Toy Bar 3 Toys Seat Back Tube Pad Retainer Footrest Retainer Right Base Wire Base Tube #8 x 3/4" Screw - 2 Left Base Wire Shown Actual Size 3
Battery Installation + 1.5V “D” (LR20) – SHOWN ACTUAL SIZE Battery Compartment Door + – • Locate the soothing unit on the footrest. • Insert a coin into the battery compartment door and pry the battery compartment door off. • Insert one “D” (LR20) alkaline battery, as indicated inside the battery compartment. Be sure to place the battery on top of the ribbon. • Replace the battery compartment door and be sure it snaps securely closed.
Assembly CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Right Base Wire Colored Tabs Base Tube 1 Left Base Wire • Place the base tube on a flat surface as shown. • Position the left and right base wires as shown. Note the location of the colored tabs on the left and right base wires. • Fit the left base wire into the base tube. • Fit the right base wire into the base tube.
Assembly Footrest with Soothing Unit Flex Base Wires Inward Tab Tab 2 Base Tube Base Wire • Position the footrest so that the soothing unit is upright. • While flexing the base wires toward Colored Tab each other, hook the footrest onto the Back View ends of the base wires. • Push the footrest down completely to the tabs on the base wires. • Make sure the colored tabs on the left and right base wires are visible through the base tube holes (see inset).
Assembly Base Wire Seat Back Tube Base Wire 3 • Position the seat back tube above the base assembly. • Fit the seat back tube completely onto the base wires.
Assembly Retainer Socket Up Retainer Socket Up Seat Back Tube PULL UP 4 • Fit a retainer to the outside of the seat back tube, as shown. Make sure the socket in the retainer is upright. • Insert a screw through the hole in the seat back tube, base wire and into the inside of the retainer. • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to assemble the other retainer to the other side of the seat back tube.
Assembly Pad Footrest Soothing Unit Seat Back Tube Fastener 5 • Position the pad above the frame with the blanket toward the soothing unit. • Fit the upper pocket on the back of the pad onto the seat back tube . • Lift the footrest. Fit the lower pocket on the back of the pad onto the footrest . Lower the footrest. • Attach the pad fastener to the fastener on the soothing unit .
Assembly Toy Bar Strap Retainer Socket Retainer Socket Toys Plugs 6 • • • • • Fit the toy bar plugs into each retainer socket. Unfasten a strap on the toy bar. Wrap the strap around a toy ring and re-fasten the strap. Repeat this procedure to attach the other two toys to the toy bar. The toy bar is removable. Simply pull to remove.
Set-Up & Use WARNING To prevent serious injury and/or falls: • Never use on any elevated surface, since child’s movement may cause bouncer to slide or tip over. • Never use as a carrier or lift while child is seated. • Always use the restraint system. • Never leave child unattended. • Never use with a child able to sit up unassisted. Belt 1 Buckle Restraint Securing Your Child • If the toy bar is attached, remove it before placing your child in the seat. • Place your child in the seat.
Set-up & Use Anchored End Buckle Buckle Anchored End 2 Free End Free End Loosen Tighten To tighten the restraint: • Feed the anchored end of the belt up through the buckle to form a loop . • Pull the free end of the belt . • Repeat this procedure to tighten the other belt. To loosen the restraint: • Feed the free end of the belt up through the buckle to form a loop . Enlarge the loop by pulling on the end of the loop toward the buckle.
Set-up & Use Blanket 4 • Fold blanket up on baby’s lap. Storing the Blanket • Pull the blanket down completely. • Fold the blanket under the footrest wire. • Tuck the blanket into the pocket on the underside of the pad.
Care The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the soothing unit.
FCC Note (United States Only) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Consumer Information Questions? We’d like to hear from you! Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM – 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Relations 636 Girard Avenue East Aurora, New York 14052 For other countries, outside the United States: Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
