User Manual

Gup Speeders
Speedway
Gup Speeders
Speedway
INSTRUCTIONS
Keep these instructions for future reference as they contain important information.
Item No : CJJ12_1100383434_DOM
Size : 630mm
x
297mm
Paper : 100% Recycled Paper, 70 gsm
Color : Black
Date : Feb 16, 2015 (Veela)
TRACK SET ASSEMBLY
ADULT ASSEMBLY REQUIRED. No tools required for assembly.
Attach the WALL PLATE to your wall using the enclosed Command® Strip.
D E F
H J K L
B
WALL PLATE ASSEMBLY
NOTE:
Only apply Command® Strip to surfaces above 50°F (10°C).
Adhesive could lose adhesion above 105°F (40°C).
CAUTION:
DO NOT use with wallpaper. May not adhere well to vinyl surfaces.
DO NOT use for antiques, heirlooms, or other valuable or irreplaceable items.
DO NOT hang items over beds.
IMPORTANT: Failure to follow instructions carefully may cause damage to your wall!
SAVE INSTRUCTIONS for damage-free removal or visit command.com
To remove MOUNTING BASE permanently from wall:
IMPORTANT NOTE:
Do not remove the MOUNTING BASE from the wall in between play sessions.
Remove only the WALL PLATE from the MOUNTING BASE in between play sessions.
Once the MOUNTING BASE is removed from the wall, it cannot be re-attached using the same Command® Strip.
!
NEVER pull the Command® strip towards
you (as shown).
Hold the MOUNTING BASE gently to
prevent the base from snapping
your fingers.
Stretch straight down along wall at least
12 inches (30 cm) until MOUNTING BASE
and the strip release.
1100383434_DOM
CJJ12
CONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
OCTONAUTS™ OCTOPOD™ Meomi Design Inc.
OCTONAUTS Copyright © 2015 Vampire Squid Productions Ltd,
a member of the Silvergate Media group of companies. All rights reserved.
©2015 Mattel. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, except as noted.
PRINTED IN CHINA. Mattel East Asia Ltd., Room 503-09, North Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
3M and Command are trademarks of 3M. © 3M 2015. All Rights Reserved.
NOTE: DO NOT ATTEMPT TO PULL MOUNTING BASE OFF OF WALL WITHOUT READING THE FOLLOWING REMOVAL INSTRUCTIONS!
!
To remove WALL PLATE from wall:
NOTE: You can remove the WALL PLATE from the MOUNTING BASE in between play sessions, but do not remove the MOUNTING BASE from the wall.
side view
front view
Pull the WALL PLATE gently from the bottom to unsnap the MOUNTING BASE from the WALL PLATE.
WHAT’S INCLUDED
TRACK LAYOUT
G
Separate strips. Remove RED-printed liner from
Command® Strip.
Measure off 14.7 inches / 37.5 cm using the ruler found on the side of the
instruction sheet.
Press MOUNTING BASE firmly to wall for 30 seconds.
Proceed to TRACK SET ASSEMBLY.
IMPORTANT:
For maximum holding strength wait 1 hour before
attaching the WALL PLATE (Step 18).
1 HOUR
Press Command® Strip to MOUNTING
BASE firmly for 30 seconds.
Clean surface of wall with isopropyl
rubbing alcohol, wipe gently, let dry.
Do not use household cleaners.
Remove BLACK-printed liner from
the other side of the Command® Strip.
C
x
2
A
x
2
flat surface/floor
14.7’’ 37.5cm Bottom of MOUNTING bracket
1
(inch)
(cm)
2 3 4 5 6 7 8 9 10 11 12 13 14
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
I
11
F
12
19
E
C
10
13
C
16
H
17
B
20
After 1 hour, snap the
WALL PLATE onto the
MOUNTING BASE and
continue with the
TRACK SET ASSEMBLY
of your GUP Speeders
Raceway.
side view
18
front view
D
D
NOTE: Be sure the track curves to the RIGHT and not to the LEFT in order for the shark feature to work correctly.
G
x
2
I
x
Press adhesive side of Command®
Strip to back of MOUNTING BASE.
K
Make sure the strip tab is accessible
for future removal.
A
14
AJ
15
9
1 2 4
7
5
8
3
6