L E A R N I N G ™ S N R E P A T T Infant-to-Toddler Rocker Toddler Seat Infant Seat Model Number: 79026 Please keep this instruction sheet, as it contains important information. Use the upright position only when your child has developed enough upper body control to sit without leaning forward. Always use the restraint until your child is able to climb in and out of the chair unassisted. Designed for use with children from birth to 40 lbs (18 kg). Adult assembly is required.
Warning Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. The kickstand is packaged within the pad at the factory. Before beginning assembly, please remove kickstand from the pad. WARNING To prevent serious injury and/or falls: • Never use on any elevated surface. • Always use the restraint until the child is able to climb in and out of the chair unassisted. • Never leave child unattended.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. #8 x 3/4" Screw Shown Actual Size Cross Brace CAUTION This package contains small parts in its unassembled state. Adult assembly is required.
Assembly Side Rail Side Rail Hole Front Tube Side Rail Front Tube 4 Vibrations Unit 5 Side Rail Hole • Locate the hole in each side rail. • With the vibrations unit facing forward, fit the front tube to the side rails, as shown. Hold the front tube in place and proceed to step 5. • Insert a #8 x 11/4” screw through the outside of each side rail and into the ends of the front tube.
Assembly Retainer with Lock Nut Kickstand Press Tab Press Tab 6 Rounded Side 7 Receptacles M4 Lock Nut - 2 (Inside Retainer) • Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail. Shown Actual Size • Position the assembly face down, as shown. • While pressing the tab on each end of the kickstand, insert the kickstand into the receptacle in each side rail, as shown. • Push the kickstand into the receptacles until the tabs “snap” into place.
Assembly Pad Pad Slot Press Seat Back Seat Back Tube 8 • Turn the assembly upright. • Fit the upper pocket on the pad onto the seat back tube. • Fasten the pad buckles around each side rail. Hardboard 9 Side Rail • Turn the hardboard over and insert it into the Pad slot in the front edge of Buckles the pad. • Fasten the pad buckles on the front edge of the pad and underneath the seat. Make sure you hear a “snap” on both sides. • Press the fasteners together in the seat back portion of the pad.
Battery Installation Battery Tips + 1.5V “D” (LR20) – SHOWN ACTUAL SIZE • Remove the battery during long periods of non-use. Always remove an exhausted battery from the product. Battery leakage and corrosion can damage this product. Dispose of the battery safely. • Do not dispose of the battery in a fire. The battery may explode or leak. • Do not dispose of the musical toy in a fire. The battery(ies) inside the toy may explode or leak. • Never short circuit the battery terminals.
Set-Up & Use Securing your Infant IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. WARNING To prevent serious injury and/or falls: • Always use the restraint until child is able to climb in and out of the chair unassisted. • Never use on any elevated surface. • Never leave child unattended.
Toys Securing your Infant Anchored End Anchored End Strap B Strap Strap B Toy Free End 3 Tighten Toy Free End Loosen To tighten the belts: • Feed the anchored end of the restraint belt up through the buckle to form a loop . • Pull the free end of the restraint belt B . • Repeat this procedure to tighten the other restraint belt. 4 To loosen the belts: • Feed the free end of the restraint belt up through the buckle to form a loop .
Calming Vibrations Toy Bar Toy Bar Plug Plug 6 Toys Power Switch • Make sure your child is properly secured in the seat. • Slide the power switch to the on position for calming vibrations. • Slide the power switch to the off position to turn vibrations off. 5 • Fit the plugs on each end of the toy bar into the sockets in each side rail. • Fit the toy bar straps through the slot in the toy rings. Fasten the straps. • Or, attach the toys to the pad straps (see Step 4).
Kickstand Storing the Restraint System for Toddler Use Small Slot Small Slot 7 8 Kickstand • Rotate the kickstand out. • Push down on the seat bottom to be sure the kickstand is in position. Large Slot • Insert the restraint belts back through the small slots in the pad. • Insert the restraint pad down through the large slot in the pad. 9 11 • Turn the rocker face down. • Tuck the ends of the restraint pad underneath the buckles, as shown.
Care FCC Note (United States Only) • The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. • The frame, toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. To remove the pad: • Unfasten the buckles around each side rail. • Turn the seat face down on a flat surface.