74120 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Requires four “C” (LR14) alkaline batteries for the mobile and two “AA” (LR6) alkaline batteries for the remote control (batteries not included). Tool required for battery installation: Phillips screwdriver (not included). www.fisher-price.
Consumer Information WARNING Possible entanglement injury. • Keep out of baby’s reach. • Remove mobile from crib or playpen when baby begins to push up on hands and knees. • This product will not attach to all crib designs. Do not add additional strings or straps to attach to crib or playpen. • The mobile may be used from birth until 5 months. • A crib mobile is intended for visual stimulation and is not to be grasped by a child.
Parts Upper Arm Spiral Remote Control Star Retainer Lower Arm Clamp 3 Soft Toys #6 x ½" Screw - 1 Shown Actual Size CAUTION This toy contains small parts in its unassembled state. Adult assembly is required.
Battery Installation Battery Compartment Door Mobile • Locate the battery compartment door on the mobile’s lower arm. • Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert four “C” (LR14) alkaline batteries. • Replace the battery compartment door and tighten the screws with a Phillips screwdriver. Do not over-tighten.
Battery Installation Battery Compartment Door Remote Control • Locate the battery compartment door on the back of the remote control. • Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert two “AA” (LR6) alkaline batteries, as indicated inside the battery compartment. • Replace the battery compartment door and tighten the screw with a Phillips screwdriver. Do not over-tighten.
Battery Installation - 1.5V x 4 “C” (LR14) + + 1.5V x 2 “AA” (LR6) - Hint: We recommend using alkaline batteries for longer battery life. Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
Assembly 1 Upper Arm Lower Arm • Fit the upper arm into in the lower arm. 21 Star Retainer Battery Compartment • Insert the star retainer into the hole in the lower arm on the side opposite the battery compartment. • Insert the #6 x ½" screw into the lower arm as shown. Tighten the screw with a Phillips screwdriver. Do not over-tighten.
Assembly 1 3 Wide Clamp Upper Arm Narrow- Clamp Spiral • Note that the spiral has a wide clamp on one end and a narrow clamp on the other end. • “Snap” the spiral wide clamp onto the post above the star on the upper arm. • “Snap” the spiral narrow clamp onto the post below the star on the upper arm. 41 Threaded Peg Crib Top Rail Clamp • Fit the mobile against the crib top rail so that the threaded peg extends out of the crib.
Use Power/Volume Switch • The switch has three positions: off ; on with low volume and on with high volume . • Slide the power/volume switch to the off position when not in use.
Use IMPORTANT! • In the unlikely event that use of the remote interferes with normal use of other remote controlled equipment, such as televisions and stereos, or use of other electric or battery powered appliances interfere with operation of the mobile, do not use both appliances at the same time. • For best performance between the mobile and the remote, avoid using the remote in areas of bright light. In bright natural or artificial light, you may notice loss of range.
Care • Wipe the toy with a clean cloth dampened with a mild soap and water solution. • Do not immerse the toy. Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).
FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.