ACTIVESMART™ INTEGRATED FRENCH DOOR REFRIGERATOR FREEZER RS80 and RS90 models INSTALLATION GUIDE NZ AU GB IE HK SG IN 862068B 08.
CONTENTS 1 SAFETY AND WARNINGS 2 COMPONENTS 3 TOOLS 4 APPLIANCE AND CAVITY DIMENSIONS 5 CABINETRY OPTIONS 7 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS 8 CUSTOM DOOR PANEL INSTALLATION TEMPLATE 9 DOOR CLEARANCE !0 ELECTRICAL AND PLUMBING !1 BEFORE INSTALLATION !2 CAVITY PREPARATION !3 WATER SUPPLY CONNECTION !4 POWER SUPPLY CONNECTION !5 INSTALLATION PREPARATION !6 POSITIONING INTO CABINETRY !7 ALIGNING INSIDE CABINETRY !8 DOOR PANEL INSTALLATION — STAINLESS STEEL OR !9 DOOR PANEL INSTALLATION — CUSTOM @0
1 ! SAFETY AND WARNINGS WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons. ! WARNING! Cut Hazard Take care — panel edges are sharp. Failure to use caution could result in injury or cuts. IMPORTANT! ● ● ● ● ● ● ● ● ! WARNING! This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
2 COMPONENTS Internal box (Installation kit) Located inside appliance A A Z Z Anti-tip bracket assembly kit External box Taped to back panel of appliance B Door panel attachment kit C Door / drawer trim install kit Door side trim (2) Toe kick grille (1) Side cover (4) Drawer side trim (2) Drawer top trim (1) Top cover (2) Double-sided door panel template (1) Side bracket (10) Dual adhesive tabs (6 per each strip) (12) Masonry plug (4) Side strap (10) #8x16 countersunk screw (36) #8 x 1
2 COMPONENTS Miscellaneous items (MI) pack Located inside the appliance ACTIVESMART™ INTEGRATED ACTIVESMART™ INTEGRATED REFRIGERATOR SLIDE-IN REFRIGERATOR RS90A, RS9120W, RS90 & RS90AU models RS36A72, RS36A80 & RS36W80 models SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE & GARANTIE HUOLTO JA TAKUU USER GUIDE NZ AU GB IE HK SG IN US SERVICE OG GARANTI INSTALLATION GUIDE 保修和维修 NZ AU GB IE HK SG IN 服務和保修 844219B 02.
2 3 COMPONENTS Door panel set Not supplied and must be purchased separately Stainless steel (Fisher & Paykel) door panel set: Includes 2x French door panels and 1x drawer panel.
4 APPLIANCE AND CAVITY DIMENSIONS IMPORTANT! D For ease of installation, ensure cavity width is consistent top to bottom and height is consistent left to right.
5 FRAMELESS CABINETRY (Aligns the appliance with the cabinetry) CABINETRY OPTIONS FRAMED CABINETRY (Aligns the appliance with the frame of the cabinetry) Flush installation Note: Drawings are only for reference and not the actual cavity width of the cabinetry.
6 DOOR PANEL DIMENSIONS IMPORTANT! Custom door panels can only be used for non-Water dispensing models.
7 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS — RS80 Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. 342.3mm 54.8mm Ø 2mm REF 12x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). 633.6mm 1016mm 981mm Ensure handle is mounted 65mm from inner edge of panel to the center — this will avoid interference with brackets. 683.6mm 34.
7 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS — RS90 Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. 392.3mm 54.8mm Ø 2mm REF 12x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). 633.6mm 1016mm 981mm Ensure handle is mounted 65mm from inner edge of panel to the center — this will avoid interference with brackets. 683.6mm 34.
DRAWER PANEL LEFT EDGE LH DOOR PANEL HANDLE SIDE SIDE BRACKET HOLES SIDE BRACKET HOLES SIDE BRACKET HOLES RH DOOR PANEL HANDLE SIDE DRAWER PANEL RIGHT EDGE DRAWE PANEL HANGING BRACKET HOLES DRAWE PANEL HANGING BRACKET HOLES SIDE BRACKET HOLES LH DOOR PANEL HINGE SIDE RH DOOR PANEL HINGE SIDE 1 REV FISHER & PAYKEL APPLIANCES LIMITED SCALE: 1:1 DRAWE PANEL HANGING BRACKET HOLES REVISION: 1 DRAWER PANEL RIGHT EDGE DRAWER PANEL TOP EDGE DRAWER PANEL LEFT EDGE DRAWE PANEL SIDE BRACKET HOLES DRA
9 DOOR CLEARANCE DD EE Insert hinge limiting pin B BC C AA B BC C AA WARNING! ● ● Wall 115° DOOR OPENING (FULL INTERNAL ACCESS) 115° DOOR OPENING 115° DOOR OPENING [FULL ROTATION] [FULL ROTATION] Wall 90° DOOR OPENING DOOR OPENING 90°90° DOOR OPENING Before opening the doors, ensure that the appliance is stable. Follow these steps to avoid risks that can cause serious injury or death. For 90° door swing, a hinge limiting pin is supplied with your appliance.
!0 ELECTRICAL AND PLUMBING IMPORTANT! ● ● Electrical connection should be located in an adjacent cabinet to either side of the appliance or above the appliance cavity. We recommend to use an isolating switch that is easily accessible to the user after the appliance is installed. WARNING! Electrical shock hazard. Assume all parts are live. Disconnect supply before servicing and installation.
!0 ELECTRICAL AND PLUMBING Maximum distance of hose and power cord Water inlet hose* — 2250mm Power cord (excl.plug) — 800mm LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose* — 3180mm Water inlet hose* — 3930mm Power cord (excl.plug) — 2050mm Power cord (excl.plug) — 2050mm * Applicable to Ice and Water models only. RS80 RS90 ELECTRICAL SPECIFICATIONS RS80 RS90 Supply 13mm (1/2") or 19mm (3/4") BSP threaded water connection 6.
!1 BEFORE INSTALLATION IMPORTANT! ● ● ● ● Be careful when unpacking to prevent damage to the surface of your appliance. Ensure that the appliance is stable to prevent from tipping over when unpacking. Do not open the doors to prevent the appliance from tipping over. The appliance is heavy and requires a minimum of 2 persons to unpack and install. ● ● ● Ensure that the feet of the appliance are retracted. If the appliance is damaged, contact your Fisher & Paykel dealer.
!1 BEFORE INSTALLATION IMPORTANT! ● ● Your appliance is fitted with front and rear rollers designed for moving the appliance forward and backward. Do not move the appliance sideways as this may damage the rollers or the floor covering / surface. The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection and water leaks.
!2 IMPORTANT! Internal box ● A Anti tip bracket kit ● ● Anti-tip bracket (1) CAVITY PREPARATION The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand 100kg load. Ensure that anti-tip bracket is installed correctly to prevent the appliance tipping forward when door is open. Ensure the bracket is secured to structural beams or wall studs nearest to the center of the alcove.
!3 IMPORTANT! Water fittings kit (Ice and Water models only) ● ● ● ● Water tap adaptor (1) WATER SUPPLY CONNECTION The water connection instructions below are intended only for the professional installer. The appliance comes with a pre-connected plastic water tubing. Water fittings are not supplied and must be purchased separately. Ensure the appliance is connected to its own isolating switch.
!4 Internal box Y Miscellaneous components POWER SUPPLY CONNECTION DETAIL B SCALE 1 : 5 Alternative water and electrical connection (above the cavity) Connect to power supply 1 Locate the power cord and connect the fitted plug to the electrical supply (230VAC, 50Hz). Turn ON the appliance. –– We recommend to use an isolating switch that can be accessed easily after the appliance is installed. 1 Connect the water fittings to the water supply (C).
18 O L ● X INSTALLATION PREPARATION WARNING! Internal box Install fasteners kit !5 ● Be careful when working with the appliance outside of the finished enclosure. Ensure that the appliance is secured to prevent tipping forward. Tipping of appliance can lead to serious injury or death. Remove hinge end caps M5x10 cross-head screw (10) 1 Open the French doors carefully. Tools Cross-head screwdriver A C D Powered driver (optional) 1 – 2 turns B 2 Remove the left hinge end cap.
!6 POSITIONING INTO CABINETRY IMPORTANT! ● ● Your appliance is fitted with front and rear rollers designed for moving the appliance in the forwards and backwards direction. Avoid moving the appliance in a sideways direction as this may damage the rollers or the floor covering/surface. ● ● Ensure the hose is not run over by the appliance when pushing into the cabinetry to prevent damage and possible water leaks.
!7 IMPORTANT! Supplied tools ● ● Hex key ● ● Tools ALIGNING INSIDE CABINETRY Ensure all four corners of the appliance is supported firmly onto the floor to eliminate any movement. DO NOT install the appliance on a soft, uneven, or unlevelled floor to avoid twisting the appliance and poor door sealing. We recommend to use A 4mm hex key. One turn of height adjusting nuts is equivalent to 1mm height adjustment. Note: Maximum height adjustment is 20mm.
!8 IMPORTANT! Internal box ● B Door panel attachment kit Side bracket (10) DOOR PANEL INSTALLATION — STAINLESS STEEL ● ● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Ensure to protect the finish of the Stainless steel door panels. For non-water dispensing door panels: Leave the protective film on the panels when hanging and remove the film only when installation is complete.
!8 IMPORTANT! Ice and Water display (Ice and Water models only) External display module (1) DOOR PANEL INSTALLATION — STAINLESS STEEL ● ● Failure to follow these steps can lead to difficulties in door panel adjustment and cosmetic cap fitment. For water dispensing door panels: Remove the protective film from the appliance doors before hanging door panels.
!8 Tools DOOR PANEL INSTALLATION — STAINLESS STEEL Attach the door panels 1 Open the door and loosen the M5x10 cross-head screws (do not remove) at the sides of the doors (A). 2 Hang the door panel by inserting the M8 studs Cross-head screwdriver through the holes of the hanging bracket (B). 3 Slide the forks of the side brackets onto the screws of the door (C).
!8 B Door panel attachment kit DOOR PANEL INSTALLATION — STAINLESS STEEL IMPORTANT! ● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Adjust the door panels 8x16 mush washer screw (2) 1 Push the appliance into the cavity until the door panels are flush Tools 2 Place a ruler on the front of the appliance to check flushness top with adjacent cabinetry surface. and bottom, left and right..
DRAWER PANEL HANDLE SIDE RH DOOR PANEL HINGE SIDE DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES DRAWER PANEL HINGE SIDE DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HINGE SIDE RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES LH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HINGE SIDE RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES
RH DOOR PANEL HINGE SIDE DRAWER PANEL HANDLE SIDE RH DOOR PANEL HINGE SIDE DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HINGE SIDE DRAWER PANEL HINGE SIDE RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HINGE SIDE DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES DOOR PANEL SIDE BRACKET HOLES RH DOOR PANEL HANDLE SIDE DOOR PANEL SIDE BRACKET HOLES
!9 DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! back side of drawer panel Use left door panel template to use for the drawer panel. Place the template at the back side of the drawer panel.
!9 Internal box B Door panel attachment kit DOOR PANEL INSTALLATION — CUSTOM Remove hanging brackets 1 Remove the M8 washers and M8 nuts from the M8 studs at the top the door (A) using the hex key and spanner. Keep the washers and nuts to reuse later. 2 Remove the hanging bracket from the top of each door and set aside (B) for later installation.
!9 Tools DOOR PANEL INSTALLATION — CUSTOM Attach the door panels 1 Open the door and loosen the M5x10 cross-head screws (do not remove) at the sides of the doors (A). Hex key 2 Hang the door panel by inserting the M8 studs through the holes of the hanging bracket (B). 3 Slide the forks of the side brackets onto the screws of the door (C). 4 Screw the M8 washer and nut to each stud (D), FPA spanner (1) and re-tighten the side screws (E) to fix the door panel (do not fully tighten).
!9 B Door panel attachment kit DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! ● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Adjust the door panels 8x16 mush washer screw (2) 1 Push the appliance into the cavity until the door panels are flush Tools 2 Place a ruler on the front of the appliance to check flushness top with adjacent cabinetry. and bottom, left and right.
@0 Internal box X Install fasteners kit FIXING TO CABINETRY IMPORTANT! Lower the feet until it engages the floor to provide more stability to the appliance and prevent back and forth movement. #8Gx19 twin thread screw (2) Tools B C Cross-head #8 xscrewdriver 19 Countersunk Twin Thread Posi Screw Powered driver (optional) Secure the hinge bracket to cabinetry 1 Secure the hinge bracket to the ceiling of the cabinetry with #8Gx19 twin thread screw (A). Repeat on the opposite side.
@1 Miscellaneous items pack WATER FILTER INSTALLATION IMPORTANT! ● The water filter head must be firmly pushed into the appliance and secured. incorrect installation can lead to water leaks. Water filter (1) Filter handle B Filter cartridge tool (1) A FRONT VIEW Filter in locked position Install the water filter 1 Remove the plastic wrapping of the new filter.
@2 MI Pack TOE KICK INSTALLATION Install the toe kick filter and grille 1 Fit the filter onto the rails and push until it clips securely (A). 2 Align the top grille clips to the top plinth slots. Ensure the top grille is in the correct orientation (B). 3 Push the grille firmly onto the appliance until the clips engage (C).
@3 Internal box C Door / drawer trim install kit COVERS AND TRIMS INSTALLATION Attach the covers Attach the drawer top and side trims 1 Open the French doors. 3 Peel off two dual adhesive tabs and press them together Attach the top covers (A) firmly over the top studs, and the side covers (B) to the side brackets. to form a pair (E). Remove the adhesive backing on one side only. 4 Press firmly to the underside of the drawer top trim in the indicated locations (F).
@4 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Ensure all internal and external packaging is removed from the appliance before use. Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the doors / drawer can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting pin is fitted for 90° door swing.