BUILT-IN OVEN OB24SDPT models INSTALLATION GUIDE US CA 591944A 07.
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. • Connection to a good ground wiring system is absolutely essential and mandatory.
PARTS SUPPLIED Screws (2) Metal side shelves fixing nut (2) PRIOR TO INSTALLATION Ensure that: zz zz zz zz zz zz zz zz zz the countertop and oven cavity are square and level, and are the required dimensions the installation will comply with all clearance requirements and applicable standards and regulations the isolating switch will be easily accessible to the customer with the oven installed the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavit
PRODUCT DIMENSIONS b a d PROFILE FRONT h e PRODUCT DIMENSIONS INCHES MM A Overall height of oven 23 9/16 598 B Overall width of oven 23 7/16 596 22 1/4 565 D Height of chassis 22 5/8” 575 E Width of chassis 21 7/8 556 F Depth of chassis 21 7/16 545 G Depth of oven frame and control panel (distance between front of chassis and front of oven door, excl.
CABINETRY DIMENSIONS PROUD INSTALL b e a 5/8 - 13/16” (16-20mm) d c PROFILE CABINETRY DIMENSIONS PLAN OB24SDPT MODELS INCHES MM A Minimum inside width of cavity 21 1/16 560 B Overall width of cabinetry 23 5/8 600 22 13/16 580 D Overall height of cabinetry 23 5/8 600 E Minimum inside depth of cavity 21 5/8 550 C Minimum inside height of cavity FLUSH INSTALL 5/8 - 13/16” (16-20mm) If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manuf
DISCARD PACKAGING RESPONSIBLY Remove the accessories box from the top of the oven and set aside. Recycle responsibly.
CONNECT THE OVEN TO THE MAINS SUPPLY Nameplate location Junction box locations OB24SDPT MODELS VOLTAGE MAX. CURRENT DRAW MAX LOAD 208 V 16.6 A 3.5 kW 240 V 19.4 A 4.6 kW junction box location for undercounter installation junction box location for wall installation Connection methods box cable from power supply red wires a black wires white and green grounding oven wires - factory taped box red wires U.L.
SECURE THE OVEN TO THE CABINETRY IMPORTANT! zz zz zz 1 2 3 4 8 Do not lift the oven by the door handle. Do not over-tighten the screws. Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal. Position the oven in the prepared cavity. Open the oven door fully. Mark and pre-drill the screw holes. Use the supplied screws to secure the oven to the cabinetry.
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER TEST OPERATION: Ensure the oven is level and securely fitted to the cabinetry. Turn the power to the oven on. The display should light up. Set the clock following the instructions in the ‘User guide’. Check the lower trim is undamaged. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. Set the oven to Bake at 50oC.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. US CA 591944A 07.
FOUR ENCASTRÉ Modèles OB24SDPT GUIDE D’INSTALLATION CA 591944A 07.
CONSIGNES DE SÉCURITÉ ET MISES EN GARDE ! MISE EN GARDE! Risque de choc électrique Le non-respect de cette consigne peut entraîner un choc électrique ou la mort. • La connexion à un système de mise à la terre convenable est absolument essentielle et obligatoire. • Les modifications au système de câblage domestique doivent être effectuées uniquement par un électricien qualifié.
PIÈCES FOURNIES Vis (2) Écrou de fixation des grilles latérales métalliques (2) AVANT L’INSTALLATION Assurez-vous que: zz zz zz zz zz zz zz zz zz la cavité du four et le comptoir sont de niveau et bien droits, avec les dimensions requises. l’installation sera conforme à toutes les exigences de dégagement et les normes et réglementations en vigueur. le client pourra accéder facilement à l’interrupteur de sectionnement une fois le four installé.
DIMENSIONS DU PRODUIT b a d DE PROFIL DE FACE h e DIMENSIONS DU PRODUIT POUCES MM A Hauteur hors tout du produit 23 9/16 598 B Largeur hors tout du produit 23 7/16 596 22 1/4 565 D Hauteur du châssis 22 5/8” 575 E Largeur du châssis 21 7/8 556 21 7/16 545 G Profondeur du cadre de four et du panneau de commande (distance entre le devant du châssis et le devant de la porte du four, excl.
DIMENSIONS DES ARMOIRES INSTALLATION SUPERPOSÉE b e a 5/8 - 13/16” (16-20mm) d c DE PROFIL DIMENSIONS DES ARMOIRES EN PLAN MODÈLES OB24SDPT POUCES MM A Largeur intérieure minimale de la cavité 21 1/16 560 B Largeur hors tout des armoires 23 5/8 600 22 13/16 580 D Hauteur hors tout des armoires 23 5/8 600 E Profondeur intérieure minimale de la cavité 21 5/8 550 C Hauteur intérieure minimale de la cavité INSTALLATION ENCASTRÉE 5/8 - 13/16” (16-20mm) Si une surface de cuisson doit êt
METTEZ L’EMBALLAGE AU REBUT DE MANIÈRE RESPONSABLE Retirez la boîte d’accessoires du dessus du four et mettez-la de côté. Recyclez de manière responsable.
RACCORDEMENT ÉLECTRIQUE À LA BOÎTE DE JONCTION Plaque signalétique Emplacements des boîtes de jonction MODÈLES OB24SDPT TENSION CONS. COURANT MAX. CHARGE MAX. 208 V 16.6 A 3.5 kW 240 V 19.4 A 4.
FIXEZ LE FOUR AUX ARMOIRES IMPORTANT! zz zz zz 1 2 3 4 8 Ne soulevez pas le four par la poignée de porte. Ne serrez pas excessivement les vis. Ne scellez pas le four dans les armoires avec de la silicone ou de la colle. Cela rendrait difficile tout travail d’entretien futur. Fisher & Paykel n’assumera pas les frais liés au retrait du four ou aux dommages causés par ce retrait. Positionnez le four dans la cavité préparée. Ouvrez complètement la porte du four. Marquez et pré-percez les trous de vis.
LISTE DE VÉRIFICATION FINALE À ÊTRE REMPLIE PAR L’INSTALLATEUR FAITES UN ESSAI Assurez-vous que le four est de niveau et fixé solidement aux armoires. Activez l’alimentation du four. L’afficheur doit s’allumer. Réglez l’horloge en suivant les instructions dans le ‘Guide d’utilisation’. Vérifiez que la moulure inférieure n’est pas endommagée.
FISHERPAYKEL.COM Droit d’auteur © Fisher & Paykel Appliances 2019. Tous droits réservés. Les caractéristiques de produit présentées dans ce livret s’appliquent aux modèles et produits spécifiques qui y sont décrits à la date de publication. Dans le cadre de notre politique d’amélioration en permanence de nos produits, ces caractéristiques peuvent être modifiées à tout moment. Nous vous recommandons de vérifier auprès de votre détaillant que ce livret décrit le produit actuellement disponible.