BUILT-IN OVEN OB24SC models INSTALLATION GUIDE US CA 591362B 12.
1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! WARNING! Electrical shock hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good ground wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician Failure to follow this advice may result in electrical shock or death.
2 Screws (2) Metal side shelves fixing nut (2) 3 ● ● ● ● ● ● ● ● ● PARTS SUPPLIED PRIOR TO INSTALLATION the countertop and oven cavity are square and level, and are the required dimensions. the installation will comply with all clearance requirements and applicable standards and regulations. the isolating switch will be easily accessible to the customer with the oven installed.
5 PRODUCT DIMENSIONS B A D FRONT SIDE H E C F OB24SC MODELS G TOP PRODUCT DIMENSIONS INCHES (MM) A Overall height of product 23 9/16” (598) B Overall width of product 23 7/16” (596) C Overall depth of product (excluding handle and dials) 22 1/4” (565) D Height of chassis 22 5/8” (575) E Width of chassis 21 7/8” (556) F Depth of chassis 21 7/16” (545) G Depth of oven frame and control panel (=distance between front of chassis and front of oven door, excl.
CABINETRY DIMENSIONS PROUD INSTALL J M 5/8 - 13/16" (16-20 mm) I 13/16" Electrical supply L K (20mm) FLUSH INSTALL 5/8 - 13/16" (16-20 mm) 13/16" (20mm) SIDE TOP min.
DISCARD PACKAGING RESPONSIBLY Remove the accessories box from the top of the oven and set aside.
8 ELECTRICAL CONNECTION TO JUNCTION BOX cable from power supply Junction box location for: undercounter installation Junction box location for: wall installation red wires red wires box cable from power supply box Nameplate All models Voltage Max. current Max. draw load 208V 16.6 A 3.5 kW 240V 19.4 A 4.6 kW 1 Disconnect the power supply. 2 Remove the junction box cover. 3 Connect the oven cable to the junction box through the U.L.-listed conduit connector.
9 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Make sure the oven is level and securely fitted to the cabinetry. Check the lower trim is undamaged. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
8
9
10
FOUR ENCASTRÉ Modèles OB24SC GUIDE D’INSTALLATION CA 591362B 12.
1 CONSIGNES DE SÉCURITÉ ET MISES EN GARDE CONSIGNES DE SÉCURITÉ IMPORTANTES! MISE EN GARDE! Risque de choc électrique Avant de procéder à tout travail sur la section électrique de l’appareil, vous devez déconnecter celui-ci de l’alimentation électrique. La connexion à un système de mise à la terre convenable est absolument essentielle et obligatoire. Les modifications au système de câblage domestique doivent être effectuées uniquement par un électricien qualifié.
2 PIÈCES FOURNIES Vis (2) Écrou de fixation des grilles latérales métalliques (2) 3 AVANT L’INSTALLATION ● ● ● ● ● ● ● ● ● la cavité du four et le comptoir sont de niveau et bien droits, avec les dimensions requises. l’installation sera conforme à toutes les exigences de dégagement et les normes et réglementations en vigueur. le client pourra accéder facilement à l’interrupteur de sectionnement une fois le four installé.
5 DIMENSIONS DU PRODUIT B A D AVANT CÔTÉ H E C F MODÈLES OB24SC G DESSUS DIMENSIONS DU PRODUIT POUCES (MM) A Hauteur hors tout du produit 23 9/16” (598) B Largeur hors tout du produit 23 7/16” (596) C Profondeur hors tout du produit (excluant la poignée et les boutons) 22 1/4” (565) D Hauteur du châssis 22 5/8” (575) E Largeur du châssis 21 7/8” (556) F Profondeur du châssis 21 7/16” (545) G Profondeur du cadre de four et du panneau de commande (=distance entre le devant du châssis e
5 DIMENSIONS DES ARMOIRES INSTALLATION SUPERPOSÉE J M 5/8 - 13/16" (16-20 mm) I 13/16" Alimentation électrique L K (20 mm) INSTALLATION ENCASTRÉE 5/8 - 13/16" (16-20 mm) 13/16" (20 mm) CÔTÉ DESSUS min.
6 METTEZ L’EMBALLAGE AU REBUT DE MANIÈRE RESPONSABLE Retirez la boîte d’accessoires du dessus du four et mettez-la de côté.
8 RACCORDEMENT ÉLECTRIQUE À LA BOÎTE DE JONCTION câble d’alimentation électrique Emplacement de boîte de jonction pour : installation sous le comptoir Emplacement de boîte de jonction pour : installation au mur fils rouges fils rouges boîte Tous les modèles Tension Cons. courant max. 208 V 16,6 A 240 V 19,4 A Plaque signalétique Charge max.
9 LISTE DE VÉRIFICATION FINALE À ÊTRE REMPLIE PAR L’INSTALLATEUR Assurez-vous que le four est de niveau et fixé solidement aux armoires. Vérifiez que la moulure inférieure n’est pas endommagée. Ouvrez lentement la porte du four jusqu’à ce qu’elle soit complètement ouverte, puis vérifiez que le dégagement est adéquat entre le bas de la porte et la moulure inférieure. Cela permet d’assurer une circulation d’air convenable.
19