Integral Kit Instructions For Fisher & Paykel Cabinet widths of 635, 680, 790 mm wide ActiveSmart Models Version 6 Manual 844063 Updated September 2015
Parts supplied with Built in Kit – part number 814990 Part Qty Description Part no.
Installation dimensions For Insert Doors add 30mm (2") to A and B Cabinet Construction IMPORTANT NOTICE For a refrigerator to function to its optimum standard it requires a certain amount of air clearance around the cabinet. With integration the cabinet is essentially sealed up. As a result, the products energy, temperature and/or basic performance could be affected as compared to a freestanding product.
Internal Dimensions Model 635 Width (A) Depth (B) Height (C) PC/FC Centre line (D) E331T, RF331T 735 730 1456 E373 / C373, E308 735 730 1456 E381T, RF381T 735 730 1626 1146 E372B, RF372B 735 730 1626 657 E411T, RF411T 735 730 1726 1245 E402B, RF402B 735 730 1726 657 E415H 735 730 1726 1245 E450 / C450, E388 735 730 1726 Model 680 Width (A) Depth (B) Height (C) 976 PC/FC Centre line (D) E413T 780 730 1616 1141 E406B 780 730 1616 652 E440T 780 730 1
Hinges Illustrated below are some of the types of hinging that can be used. 790, 680 & 635 Models It is recommended that 110˚ hinges having a low profile are used, either full or half overlay such as the GRASS brand. We recommend the use of hinges that can carry a high load, especially when integrating 790 models.
1 a) b) Prepare Refrigerator for Installation Check that the internal cupboard dimensions are correct (see page 4) Unpack refrigerator protecting the floor and/or paint work from damage. Check that refrigerator door is hinged on desired side. Refer to use & care booklet for instructions to change hinge side. Remove the door handles (refer to page 7). Fit the door end cap blank to the corner of the door. Fit small plugs to the screw holes left when the door handle was removed.
How to remove refrigeration handles 1. Using a 4 mm Allen key remove the grub screw from the underneath of the handles. 2. Remove the handles. 3. Remove handle bosses. Flat Doors Designer handles Tilt the product back and remove the levelling foot circular base insert from the front levelling feet, a small flat blade screw driver can be used.
Lift the front edge of the product and slide the integration foot under the levelling foot. Push the product back to allow the outer cabinet door to close. This will be approximately 95mm (3 3/4") from the front edge of the built in cabinet to the gasket face of the refrigerator.
Align refrigerator in cupboard Slide the product toward the opening side of the cupboard. The integrated foot should touch the cupboard wall. This will set a 20mm (3/4") gap between cupboard and refrigerator. Adjust the product so it is parallel to the cabinet front to back and side to side. This is obtained by the adjustment of the front levelling feet. WARNING: Please be advised that adjustment of glass shelves is not possible once the refrigerator has been integrated.
Attach slide bracket to refrigerator doors Attach the slide bracket to the side of the door opposite to the hinges, 100mm (4") in from the edge. On a two door refrigerator use one slide bracket per door. If integrating a 790 model, we recommend using 2 slide brackets per door - one near the bottom of the door & one near the top of the door to evenly distribute the weight. The brackets should be attached to the opening side of the doors near the refrigerator and freezer compartments.
Attach slide bracket to cupboard door a) Open both cupboard and refrigerator door to 110˚ degrees. (525 compact models to 90˚) b) Put slide bracket in retainer, 120mm (43/4") approx past refrigerator door. (diagram 9). c) Check that screw A (supplied with kit) will not penetrate front surface of cupboard door (diagram 10). d) Screw slide bracket level into the cupboard door using screw A (supplied with the kit) e) Check slide mechanism does not bind through swing of door. f) Repeat for second bracket.