FIC LM2W User Guide 1
N otebook User Guide Copyright©2005 All Rights Reserved - Printed in Taiwan Notebook Computer User Guide Original Issue: 2005/6 This manual guides you in setting up and using your new notebook computer. Information in this manual has been carefully checked for accuracy and is subject to change without notice.
N otebook User Guide FCC Information to User Safety and Care Instructions No matter what your level of experience with computers, please make sure you read the safety and care instructions. This information can help protect you and your computer from possible harm. Radio and television interference Warning: Use the specified shielded power cord and shielded signal cables with this computer, so as not to interfere with radio and television reception.
N otebook User Guide You may find helpful the following booklet, prepared by the Federal Communications Commission: Interference Handbook (stock number 004000-00345-4). This booklet is available from the U.S. Government Printing Office, Washington, DC20402 Warning: The user must not modify or change this computer without approval. Modification could void authority to this equipment.
N otebook User Guide Peripheral Devices Notice Only peripherals (input/output devices, terminals, printers, etc) certified to comply with Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Optical Disk Drive Notice The optical disk drive is Class 1 Laser Product.
N otebook User Guide Directive (73/23/E E C) and the Amendment Directive (93/68/E E C), the procedures given in E uropean Council Directive 99/5/E C and 89/3360E E C. The equipment was passed. The test was performed according to the following E uropean standards: E N 300 328-2 V.1.6.1: 2004 E N 301 489-17 V1.2.1: 2002 E N 50371: 2002 E N 55022: 1998+ A1 2000+ A2 2003 E N 55024:1998+ A1 2001+ A2 2003 E N 60950: 2000 E N 61000-3-2: + A1 2001 E N 61000-3-3: 2002 802.
N otebook User Guide For DVD Players with both 525p and 625p progressive scan outputs: ‘CONSUME RS SHOULD NOTE THAT NOT ALL HIGH DE FINITION TE LE VISION SE TS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYE D IN THE PICTURE . IN CASE OF 525 OR 625 PROGRE SSIVE SCAN PICTURE PROBLE MS, IT IS RE COMME NDE D THAT THE USE R SWITCH THE CONNE CTION TO THE ‘STANDARD DE FINITION’ OUTPUT.
N otebook User Guide About Your Notebook Computer Congratulation for having purchased your new Professional Multimedia Notebook. This notebook incorporates the strongest features, which integrate the latest technologies available in the notebook industry. Your new notebook computer not only drives today multimedia applications but also be ready for tomorrow exciting new software.
N otebook User Guide About Your User Guide Welcome to your Professional Multimedia Notebook User Guide. This manual covers everything you need to know in learning how to use your computer. This manual also assumes that you know the basic concepts of Windows and the PC. You will start doing a lot of great and fun things with your computer. This manual is divided into eight chapters. Chapter 1 gives introduction on your computer features.
N otebook User Guide Table of Contents ABOUT YOUR NOTEBOOK COMPUTER ....................................... 8 ABOUT YOUR USER GUIDE................................................................. 9 1 INTRODUCTION............................................................................. 15 1.1 1.2 1.3 FEATURE HIGHLIGHT .................................................................... 16 UNPACKING THE COMPUTER .........................................................
N otebook User Guide Installing the VGA Device Driver ................................................ 43 Installing the Azalia Hotfix Driver ............................................... 43 Installing the Audio Device Driver............................................... 44 Installing the Modem Device Driver ............................................ 44 Installing ENE - Keyboard Controller driver .............................. 45 Installing ALPS - Touch Pad driver ....................................
N otebook User Guide What is Flash Memory Card? ...................................................... 69 4 FUN WITH MULTIMEDIA .................................................................. 73 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 5 CONNECTING TO PERIPHERALS ............................................. 85 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 6 USING THE USB PORT ................................................................... 86 USING AN EXTERNAL MONITOR PORT ...........................................
N 6.5 6.6 6.7 7 otebook User Guide USING THE BOOT SETUP .............................................................. 104 HOW TO EXIT THE SETUP PROGRAM ............................................ 105 HOW TO UPGRADE THE BIOS...................................................... 106 USING OPTIONS ........................................................................... 109 SYSTEM UPGRADE ................................................................................. 110 7.1 MEMORY UPGRADE ...........
N otebook User Guide Wireless devices ......................................................................... 126 AC/DC Power Supply Adapter ................................................... 126 Battery ........................................................................................ 126 Weight and Dimension ...............................................................
1 Introduction 1 Introduction Y our Notebook PC is a fully Windows compatible portable personal computer. With the latest features in mobile computing and multimedia technology, this notebook makes a natural traveling companion. With leap of technology and compact, your Notebook PC runs on a whole wide range of general business, personal productivity, entertainment, and professional applications. It is ideal for use in the office, at home, and on the road.
N otebook User Guide 1.1 Feature Highlight Before we go to identify each part of your Notebook PC, we will first introduce you to other notable features of your computer. This notebook uses the platform with certified Intel® Centrino™ Mobile Technology. It supports the new Intel® Pentium® M processor, the core-logic architecture that absolutely fits the processor and the built-in excellent Intel® PRO/Wireless solution.
1 Introduction Wide Screen LCD Display Provides extraordinary 15.4"1280 x 800 (16:10) wide screen LCD display. It is the best choice for you to watch DVD movie. Wireless LAN Intel Pro/Wireless 2200BG Network Connection, IE E E 802.11b/g Graphic System MXM (Mobile PCI-E xpress Module) for ATI M26/M24 Graphics E ngine with 128/64MB VRAM, Respectively DVD Dual The DVD Dual device pack combines two standard packs: DVD-RW combo and DVD+ RW combo.
N otebook User Guide PCI E xpress Architecture Compared to AGP architecture, PCI E xpress™ architecture enhances I/O bandwidth and advances graphics performance. Flash BIOS Flash BIOS allows you to easily upgrade the System BIOS using the Phoenix Flash utility program. Power and System Management • Integrated SMM (System Management Mode) on system chipset that shuts down components not in use to reduce power consumption.
1 Introduction ; An AC Adapter and AC Power Cord ; Li-Ion Battery Pack ; Utility Diskettes/CD ; Hardcopy User Guide/E-book ; Quick Setup Manual Carefully inspect each component to make sure that nothing is missing and/or damaged. If any of these items is missing or damaged, notify your dealer immediately. Be sure to save the shipping materials and the carton in case you need to ship the computer or if you plan to store the computer away sometime in the future. 1.
N otebook User Guide 1. Color Widescreen LCD Display 3. Keyboard 5. E asy Buttons 8. LE D Indicators • 2.7. Built-in Stereo Speaker 4. Touchpad Pointing Device 6. Power On/Resume Button Color Widescreen LCD Display The notebook computer comes with a color LCD that you can adjust for a comfortable viewing position. The LCD is 15.4” TFT color LVDS with 1280x800 (Wide XGA with ratio 16:10) resolution panels.
1 Introduction ⇓ LCD display control hot-keys allows you to adjust the brightness of the LCD. ⇓ Simultaneous display capability for LCD and external desktop computer monitor. • Built-in Stereo Speakers Integrated left and right mini stereo speakers for sound and audio output for your multimedia presentations or listening pleasure.
N otebook User Guide • Power On/Resume Button Switches the computer power on and off, or resumes whenever it is in Suspend mode. • LE D Indicators Keeps you informed of your notebook computer’s current power status and operating status. Description of the status icons appears in the latter part of this section. N OTE BOOK STATUS I CONS The Status LE D Panel keeps you informed of the notebook’s current power and operating status. E ach LE D is marked with an icon to designate the system status. 1.
1 Introduction • ⇓ Lights green when the system is powered on. ⇓ Lights green blinking when the system is in Standby mode. ⇓ Lights yellow when the battery power is low. ⇓ Lights orange when the battery power is critical low. Battery Charging LE D Lights to indicate battery in charging status. ⇓ Lights orange to indicate that the battery is in charging. ⇓ Lights orange blinking when the battery charging is in error.
N otebook User Guide • Num Lock When LE D in blue light indicates that the Num Lock key on the keyboard is activated. When activated, the embedded numeric keypad will be enabled. T HE F UNCTION OF E ASY B UTTON S 1. CPU Throttling • 2. Internet Button 3. Wireless LAN Button CPU Throttling Press this button to decrease the CPU performance speed in order to save power for extending battery life and operation time.
1 Introduction 1.4 The Front Side of the Notebook 1. Cover Switch • Cover Switch The cover (LCD panel) is locked when it is closed. Slide the button right aside to release the latch for opening the cover of the computer. 1.5 The Rear Side of the Notebook The system ports at the back of your notebook computer can connect various devices. E ach port is described as followings. 1. USB 2.0 Ports 2. VGA Port 3.
N otebook User Guide • USB 2.0 Ports The Universal Serial Bus (USB) port allows you to connect USB 2.0compliant devices (for example, printers, scanners and so on) to your notebook computer. • VGA Port Lets you attach an external monitor or projector for wider display. You can run the LCD display and the external monitor simultaneously or switch it to monitor only using the display hot-key.
1 Introduction 1.6 The Left Side of the Notebook The left side of your notebook computer provides the features shown in the following figure. 1. DC Power Port 3. Optical Disk Drive 5. Headphone Jack • 2. Modem Port 4. USB 2.0 Ports 6. Microphone Jack DC Power Port Lets you connect the AC power adapter in supplying continuous power to your notebook and recharging the battery. • Modem Port A 56K internal fax/data modem is installed. It keeps you connected to the outside world through phone line.
N otebook User Guide When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3.
1 Introduction 1.7 The Right Side of the Notebook The right side of the notebook computer offers the features shown in the following figure. 1. PCMCIA Slot 2. IE E E 1394 3. 4 in 1 card slot 4. Air-Outlet Vent 5. TV Port 6. LAN Port Right Side Features • • PCMCIA Slot ⇓ Lets you connect various PC cards such as memory card ⇓ Supports both 3V, 5V 32-bit CardBus and 16-bit PC cards.
N otebook User Guide • 4 in 1 card slot The card slot supports SD, MMC, MS (Memory Stick) and MS_Pro flash memory card format. You can use either of the 4 types flash memory cards for extra storage media. Please pay attention to correct direction when you insert the flash memory card. For more detail of flash card, you can refer to Chapter 3.9 • Air-Outlet Vent E mits the heat out of your computer and keeps it within operating temperature.
1 Introduction 1. Hard Disk Compartment 3. Battery Bay 5. Battery Release Latch 2. Battery Lock Latch 4. Memory Compartment Bottom of the System • Hard Disk Compartment Open this cover of this compartment to replace with other Hard Disk Drive. Please refer to Chapter 7 for how to replace it. • Battery Lock Latch Push the latch to the lock side to lock and secure the battery, or push the latch to the unlock side for unpacking the battery pack.
N otebook User Guide 1.9 Notebook Accessories AC Adapter The AC Adapter supplies external power to your notebook computer and charges the internal battery pack simultaneously. The AC adapter has an autoswitching design that can connect to any 100VAC ~ 240VAC power outlets. You just change the power cord if you are going to use your notebook in other countries with different connector outlets. When you connect the AC adapter, it charges the battery whether or not the notebook computer is powered on.
1 Introduction 1.10 Notebook Options DVD/ CD-RW Combo Device Pack This device pack can write data to CD-R or CD-RW CD for you to backup the data and also can read DVD/CD title. DVD dual (Dual Rewritable DVD combo) Device Pack This device pack combines following two standard packs. Using the suitable media, you can make any format of CD or DVD as you want. DVD-RW combo: This device pack can write data to CD-R or CD-RW and DVD-R or DVDRW media and also can read DVD/CD title.
Getting Started 2 2 Getting Started Y our Notebook is designed and pre-configured for easy setup and use. This chapter describes the installation steps you should follow to get the notebook up and running as quickly as possible. Contact your dealer if they have pre-installed all the needed drivers to fully operate your computer or if there is an update on the driver installation of the notebook.
N otebook User Guide 2.1 Using the Battery Pack The notebook is designed to operate with one of the following power sources: • With AC power using the AC adapter connected to an electrical outlet. • With a Lithium-Ion (Li-Ion) battery pack. You should use the AC adapter whenever it is possible, relying on the battery pack only when AC power is unavailable. Before you use your notebook computer, install and recharge the battery pack first.
Getting Started 2 Installing the Battery Pack This notebook provides the most convenient way to install the battery pack into your computer. With the extended nose directed toward the compartment, insert and push the battery pack.
N otebook User Guide When your notebook estimates that the battery only has enough charge to continue for a few minutes, it will alert you with a battery low warning beep. If you are consuming a lot of power by using the audio system, the PCMCIA slots, the hard disk drives, and optical disk drive, your notebook might run out of charge much sooner than you expect.
Getting Started 2 2.2 Connecting the AC Power Source The AC adapter provides external power source to your computer and charges the internal battery pack at the same time. The AC adapter also has an autoswitching design that can connect to any 100VAC ~ 240VAC power outlets. To connect the power adapter: 1. Plug the AC power cord into the power socket of the AC power adapter. 2. Plug the other end of the AC power cord to a live AC wall outlet. 3.
N otebook User Guide + y For the power supply of this equipment, an approved power cord has to be used. y Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. y Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC adapter). 2.3 Starting Your Computer The Power/Resume button is found on the top of the base unit.
Getting Started 2 After the test, the screen will also display a message " press < F2> to enter SE TUP ". You don’t need to run this program at the moment as your dealer already made the necessary settings for your computer optimal operation. Refer to Chapter 6 on running the SE TUP program later. After the test has completed, your computer will start to search and boot up the operating system from your hard drive.
N otebook User Guide system. If not, follow the procedures below: I NSTALLING WINDOWS XP F ROM OPTICAL DISK DRIVE To install Windows XP directly from your optical disk drive, please go to Boot menu of BIOS setup menu. Use arrow key to select "CD-ROM Drive", then use " + " or " -" to move it to the top. Go to E xit menu and select " E xit Saving Changes" . Accordingly, insert the Windows XP installation CD into optical disk drive with following the instructions on the screen to finish the installation.
Getting Started 6. Click “Next” to continue the following step. 7. Tick the option " Yes, I want to restart my computer now." , 2 and press F inish to restart your system. I NSTALLING THE VGA DE VICE DRIVE R Following is the procedure for installing the Video Accelerator 3D Adapter VGA driver to your computer: Installing VGA device driver for Windows XP 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drivers
N otebook User Guide 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drivers\WinXP\Audio\MSHDQFE \win2k_xp\us\kb888111.e xe" . 3. Click " OK" to execute the setup program. The Setup box appears 4. Tick the option " I agree" and press Next to install this driver. 5. Click “F inish” to complete it. I NSTALLING THE AUDIO DE VICE DRIVE R Your notebook computer uses the Realtek Audio controller.
Getting Started 2 Installing Modem driver for Windows XP 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click Browse button and navigate to the directory as " E :\Drivers\WinXP\modem\ssetup.exe" 3. Click “OK” to implement the setup program to install this driver. 4. Click “OK” to complete it. + Please be notified that whenever you install the TouchPad and Keyboard Controller driver , it should be install the Keyboard Controller Driver first .
N otebook User Guide 2. Click the Browse button and specify the directory as. " E :\Drivers\WinXP\Touch Pad\Setup.exe" . 3. Click " OK" to execute the setup program. The Setup box appears 4. Click Next to install this driver when screen displays this command. 5. Tick the option " Yes, I want to restart my computer now." , and press F inish to restart your system.
Getting Started 2 I NSTALLING THE LAN DE VICE DRIVE R Please follow the procedures below for installing the LAN driver: Installing LAN driver for Windows XP 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drivers\Winxp\LAN\Setup.exe" 3. Click “Next” to continue the following steps. 4. Click “Yes” to implement the setup program to install this driver.
N otebook User Guide I NSTALLING SLIE NT MODE UTILITY Installing Slient Mode Utility for Windows XP 1 . Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drivers\WinXP\Slient Mode\PM_setup.exe" . 3. Click " OK" to execute the setup program. The Welcome box appears. 4. Click “Next” then click Install to setup this driver when screen displays this command. 5. Tick the option " Finish" to complete. 2.
Using Your Notebook 3 3 Using Your Notebook T his chapter describes how to operate the standard built-in features of the notebook that you normally would use in your day-to-day computer work. If you are new to computers and to your operating system, you also need to read the manual for the operating system on how to work with your computer. It is very important to familiarize yourself well with the operating system.
N otebook User Guide 3.1 Starting Your Operating System The operating system is a must ingredient in using your computer. Without an operating system, it is like playing chess without the chessboard. It is the platform for all your software application programs to run on. The most popular operating system today is Microsoft Windows. You should have installed one operating system by your dealer unless you are an expert computer user and would need a more powerful operating system.
Using Your Notebook 1. Function Keys 3. Windows Start Menu Key 5. Windows Shortcut Key 3 2. Control Keys 4. Control Keys 6. Cursor Control Keys Keyboard Key features and operations are described below: • Function Keys Function keys are application-driven, like F 1 through F 12 can be found on the keyboard. These keys work together with the F n key to activate special functions. Some keys (printed in blue on keypad) are preprogrammed with dual functions.
N otebook User Guide • Windows keys Use the following two keys to facilitate your work: ⇓ Start Menu key Displays the Start menu. ⇓ Shortcut/Application key Provides quick access to shortcut menus. This key acts like a right mouse button. 52 • Cursor Control keys Cursor control keys let you position the cursor on the screen where you want. In the screen, the cursor is a blinking underline, block, or vertical bar depending on the application.
Using Your Notebook 3 B ASIC KE YBOARD F UNCTIONS Keypad Function Description < E nter> key. E xecute a command. Within many text editing application programs, the < E nter> key inserts a hard carriage return, just like what ordinary typewriter does. < E sc > key. Press this key to cancel or escape from a command or function. < Ins> key. Known as the Insert key. Press this key to toggle the keyboard data entry from insert to type over mode. < PrtScr> key. Known as the Print Screen key.
N otebook User Guide Keypad Function Description < Ctrl> key. Known as the Control key. Used in most application program in combination with other keys to execute a certain command. + < Alt> key. Known as the Alternate key. Used in most application program in combination with other keys to execute a certain command. < F n> + < Num Lock> key. Activates the embedded 15-key numeric keypad. The keys are color coded blue. + < Caps Lock> key.
Using Your Notebook 3 SCRE E N CONTROL KE YS Keypad Function Description < Home> key. Moves the cursor to the beginning of a screen or line. < PgUp> key. Moves the cursor up one screen at a time < PgDn> key. Moves the cursor down one screen at a time < E nd> key. Moves the cursor to the end of a screen or line. WINDOWS H OT KE YS Keypad Function Description < Start> key. Pulls up the Windows Start menu. < Right Click> key. Performs a mouse right-click function for Windows system.
N otebook User Guide Keypad Function Description Switches display between LCD, CRT, or + LCD and CRT simultaneously. To shut down or resume the built-in + system speaker volume. Increases the brightness of LCD display + incrementally. Decreases the brightness of LCD display incrementally. + Decreases the audio volume of the + notebook incrementally. Increases the audio volume of the + notebook incrementally. 3.
Using Your Notebook 3 The Glide Pad offers a number of options that let you customize how it functions. To access these options, locate the Control Panel and double click on the Mouse icon. The options let you control the size and color of the cursor, cursor speed, the accepted double-click speed, and selection button orientation. The Glide Pad works a mouse pointing device replacement that is used under Windows-based operating system.
N otebook User Guide 1. The rectangular surface acts like a miniature duplicate of your display screen. To move the mouse cursor, place the finger lightly on the sensor pad and move in the desired direction. If you reach the end of the pad, lift your finger and place it back down on the other side of the pad. 2. To select an item, click on the item by pressing the left button control or by simply tapping on the surface once. A light, quick tap always works best.
Using Your Notebook 3 under Windows. After installing the VGA driver, you would then configure the display resolution or screen size to match your LCD display panel. This notebook computer model provides Wide screen 15.4” 1280x800 (Wide XGA) resolution panels. You would also probably want to set the amount of color output to display sharper images and photos.
N otebook User Guide + You can use the + hot-key to switch the display between LCD only, CRT only, or both LCD and CRT display. CHANGING THE DISPLAY PROPERTIES UNDER WINDOWS To change the display properties of your screen under Windows system, just right-click on the desktop area and select Properties or go to the Control Panel and click on the Display icon. The Display Properties dialog box will appear on your screen. Click on the Settings tab to set your desired configuration.
Using Your Notebook 3 Standby Mode Standby Mode is mainly for power saving. When the Standby Mode is activated, your display and hard drive are shut down and all open applications and documents are stored in RAM (Random Access Memory). This allows your notebook to wake up quickly, but a low level of power is required to maintain this suspended state. How quickly your system powers down into Standby mode is up to you by setting proper times in Power Options of Control Panel in Window.
N otebook User Guide Shutdown All power has been turned off from the notebook. This means that no power including external AC power source and battery power source will be consume by the notebook. 3.6 Working with the Built-in HDD Your notebook computer is equipped with a built-in large capacity 2.5 inch IDE hard disk drive where you store or install your computer operating system and all application software programs. You need to format the hard disk before using.
Using Your Notebook 3 3.7 How to Access the Optical Drive Your system ships with an optical disk drive installed on the left side of your computer. You would normally use the drive for installing operating system and software application programs. To insert and remove a disc on the drive: 1. Make sure the computer is turned on. Press the eject button found on the door cover of the combo drive. The CD tray mechanism will pop-out slightly and slowly pull out the whole length of the tray. 2.
N otebook User Guide + If the eject function is disabled by software or a power failure occurs, the E mergency E ject Hole allows you to manually remove a CD from the reader. 4. To close the combo drive, simply push the CD tray inside. The combo drive LE D will activate when the disc is detected. Wait until the LE D has turned off and then start to read the disc. How to care the CD When you handle CDs, pay attention to the following guidelines: • Always pick up the CD by its edges.
Using Your Notebook 3 E xpressCard modules to be included in smaller host systems. Designed for both desktop and mobile use, E xpressCard use either USB 2.0 or a single lane PCI E xpress technology. The E xpressCard standard was developed by PCMCIA member companies including technology leaders, system manufacturers, card manufacturers, from all other parts of the PC Card industry. Dimensions of E xpressCard Current CardBus PC cards are 54 millimeters wide.
N otebook User Guide All E xpressCard modules are 5mm thick but the standard also allows for card developers to build longer 'extended' modules. Native Bus Connection The E xpressCard standard supports both the USB 2.0 and PCI E xpress interfaces. Card manufacturers are able to choose whichever bus is appropriate to their application; the performance of PCI E xpress, or from the wide range of solutions supported by USB. All host PC E xpressCard slots will support cards using either interface.
Using Your Notebook 3 A big part of "just working" will be the existing software support. Both Windows XP and Windows 2000 already support the E xpressCard specification, although Windows 98 and Windows Millennium E dition do not. I NSE RTING AND RE MOVING A E XPRE SSCARD Your computer includes hot swapping capability, that allows you to exchange cards while the computer is turn on and start using it immediately. Inserting E xpressCard To insert a E xpressCard into the E xpressCard slot: 1.
N otebook User Guide Removing E xpressCard To remove a E xpressCard from the E xpressCard slot, you should first disable the E xpressCard card setting in the system as described followings: 1. Double click the E xpressCard icon on the right bottom side of the task bar. 2. Select the socket from the list that you want to remove, and click Stop button. The system then disables the function of E xpressCard card. 3.
Using Your Notebook + 3 The power consumption of E xpressCard/ 54 is about 2.1W, while the consumption of E xpressCard/ 34 is about 1.3W. To save energy, press the button to disconnect the card when it is not in use. 3.9 Using Flash Memory Cards WHAT IS F LASH ME MORY CARD? Flash Memory is a memory storage media. It is used by most digital camera, moreover, it can replace the traditional floppy disk. Flash memory card is built with different form factor and brand name.
N otebook User Guide The 4 in 1 card slot is used by the following cards as SD, MS (Memory Stick ), MMC, and MS_Pro. + For a single moment, only one card can be inserted into the 4 in 1 card or CF slot Inserting Flash Memory Card To insert a flash memory card into the slot is similar to E xpressCard. You only need to pay more attention whenever insert the flash memory card into the slot with the correct side. For MMC and SD card, you should position the copper connector at the bottom side.
Using Your Notebook 3 Removing Flash Memory Card It is similar to E xpressCard for removing a flash memory card from the slot. You should first disable the card setting in the system as described in the former section. To remove the flash memory card, you should only pull out the card by finger, there is no release button for flash memory slot.
Fun with Multimedia 4 4 Fun with Multimedia T his chapter lets you make full use of all the multimedia features of your computer in having fun and excitement during work or leisure. You will learn how to mix and match the built-in sound system, use Combo drive in creating an exciting full multimedia presentation.
N otebook User Guide 4.1 Notebook Multimedia Features Your notebook computer is rich in multimedia features that make your computing fun, comfortable, exciting and easy. Your computer is well able to perform all multimedia tasks through the following: • Intel® Pentium® M Processor Dothan • Up to 2GB DDR2- SDRAM • DVD/CD-RW Combo or DVD Dual (Optional) • MXM (Mobile PCI-E xpress Module) for ATI M26/M24 Graphics E ngine. • 16-bit Audio Sound System with built-in speaker and microphone. 4.
Fun with Multimedia • 4 Sound volume adjust by K/B hot-key 4.3 Setting up the Audio Driver Properties Before you can start using the audio capabilities of your computer, you need first to setup properly the audio driver after installing Windows. If you bought your computer with Windows pre-installed, it is most likely that your dealer have configured the sound driver for you. If not, you must refer to Chapter 2 on how to setup the sound drivers for Windows. 4.
N otebook User Guide Figure 4-1 E ntertainment Programs Group The standard multimedia components are as follows: • Windows Media Player - for playing sound, video and animation files • Sound Recorder - for recording sounds and playback • Volume Control - for adjusting the volume of mixer + For more information on how to operate these multimedia components, run the program and click on the Help menu. 4.
Fun with Multimedia 4 be played back through the internal speaker or earphone jack using an external speaker, headphone, or earphone set. You can also use the files as voice annotations on many applications for more real presentation. This section will describe briefly how you can record sounds under Windows operating system. To record sounds, you need to run the Sound Recorder program from the Multimedia program groups.
N otebook User Guide 2. Click Properties in the Options main menu. 3. Click the round button for Recording and tick off each component that list in the "Shows the following Volume Controls" box. Figure 4-3 Audio Properties 4. Click OK and the Recording Control dialog box will appear. Here, you will select the input device for the recording source. If you want to record from the Combo drive with audio music, you must click on CD Player.
Fun with Multimedia 4 Figure 4-4 Recording Volume Control U SING AN E XTE RNAL MICROPHONE Your computer allows you to connect an external microphone for high quality recording. The external microphone jack is found on the left side of your computer. Use only microphone with 1/8-inch mini-jack connector. Follow the same procedure for recording voice. U SING THE B UILT -IN COMBO DRIVE You would normally use the Combo drive for recording audio music from the Audio CD. Follow these steps: 1.
N otebook User Guide F igure 4-5 Play Audio CD by Windows Media Player 4. Select the starting point where you want to start recording. 5. Switch to the Sound Recorder and press the Record button. 6. Switch immediately to the Windows Media Player and press the Play button. You can adjust the volume control so you can also hear the music while in recording. 4.6 Playing Audio and Sound Your computer has built-in twin speakers to playback audio and sound.
Fun with Multimedia 4 For more quality sound output, you can choose to connect an external amplified speaker or earphone from headphone jack. Always minimize the volume first before placing the phone set to your ear. U SING THE WINDOWS ME DIA P LAYE R The easiest way to playback multimedia media files is to run the Windows Media Player. Follow these steps: 1. Click on Start, point to Programs, Accessories, and then E ntertainment. 2. Click on Windows Media Player to start program. 3.
N otebook User Guide Figure 4-6 Windows Media Player 4.8 Using DVD DVD is the breakthrough in superb full-motion picture playback. One disc can contain at least 4.7GB of information, capable of holding one full-length movie with soundtracks, subtitles, and different languages. Much more, the DVDROM drive of your computer is backward compatible with CD-ROM drive so it allows you to use any CD as well. It also works the same as the CD-ROM.
Fun with Multimedia 4 You can use Windows Media Player to watch DVDs on your Notebook computer. Like a conventional DVD player, by using the Player, you can skip to specific titles and chapters, play sequences in slow motion, gain access to special features, and switch audio and caption languages. In addition to these conventional DVD player tasks, you can also retrieve information about each disc from the Internet.
N otebook User Guide 4.9 Using Rewritable Optical Disk Drive DVD/CD-RW Combo or DVD+ RW combo drive is a device that can write digital data to CD-R and CD-RW or DVD+ R and DVD+ RW media. With this device, you can backup your own data to CD-R or CD-RW disc for mass data storage and safely retaining. The CD-R disc can be written several times until the CD-R is full; the CD-RW disc, furthermore, can write and erase data repeatedly. Please refer to the related user manual about the CD-RW software.
Connecting to Peripherals 5 5 Connecting to Peripherals T his chapter describes how you attach peripheral devices to your notebook. You can attach a printer or mouse; connect an external monitor and keyboard, or any other peripheral device. You will learn how to use these peripheral devices with the step-by-step instructions depicted in this chapter.
N otebook User Guide 5.1 Using the USB Port USB (Universal Serial Bus) is a hardware interface that enables you to connect multiple devices (such as printers, mice, keyboards, storage devices, joysticks, digital cameras, and video conference cameras, etc.) to your notebook computer, and up to 127 devices can be attached. Besides, USB’s hot swap capability allows everything to be plugged in and unplugged without turning the system off.
Connecting to Peripherals + 5 The USB bus distributes 0.5 amps (500 milliamps) of power through each port. For the purpose of power saving, please disconnect your USB device while not in use. 5.2 Using an External Monitor Port Your computer has a 15-pin Monitor port for supporting any external CRT or LCD color monitor. You need a display signal cable (usually provided with the monitor). One end of the cable must have a 15-pin connector for the system. To connect an external monitor: 1.
N otebook User Guide 6. If you only want to show the display on the external monitor or projector and shut off the LCD display, you can use the < F n> + < F 3> hot-key to switch display type between LCD and external monitor. Keep pressing the hot-key until you get the display to external monitor only. + Refer to Chapter 3 regarding the possible E xternal CRT resolutions and how to change the display properties. 5.
Connecting to Peripherals 5 install the driver of peripheral device to connect with the IE E E 1394 port, for details please refer to the manual that comes with your peripheral device. + Please make sure that the external IE E E 1394 HDD box you purchase on local electronic store should provide external power adapter. There are different types of IE E E 1394 HDD box and hard disk from different manufactures, the power consumption has varied range.
N otebook User Guide 2. Turn on your computer and your television set. 3. Click the Start button, then point to Settings, and click Control Panel. 4. Double-click on the Display icon and point to Setting tab. 5. Click Advanced button and point to Displays tab. You can see the TV icon on the screen. 6. Please click the red button above the TV icon. Click OK, Windows now automatically detect the TV port and enable this function. 5.
Connecting to Peripherals + 5 If you use external speakers and experience the sound distortion or feedback, please lower the volume. Some factors is caused by too close locating the microphone and speakers from each other, moving away the external audio option from the unit may also help. 5.
N otebook User Guide 5.7 Using the Wireless LAN Wireless LAN is the major breakthrough in computer communication technology. It lets user connect to the LAN environment without using any wire to traditional RJ-45 jack. User can enjoy the wireless connection within the range of Access Point (AP) of LAN. Access Point (AP) is the wireless transmission and receiving device, it generally connects to the server of a LAN environment or act as a LAN hub with wireless connection.
Connecting to Peripherals 1. 5 Locate the analog phone cable in the accessories box in notebook shipping carton. E ach end of the cable has a RJ-11 connector. 2. Connect one end of the cable into a standard wall outlet. 3. Connect the other end of the cable into the computer modem port. + The speed of data transmission is dependent on the quality of telephone lines. Digitally terminated lines improve the speed of data transmission. Contact your service provider for more information.
Customizing Your Notebook 6 6 Customizing Your Notebook Y our computer uses the Phoenix BIOS Setup program that allows you to set several system configuration in changing the way your computer performs. This includes you r system time and date, disk drive configuration and password setup. This information is then stored in the CMOS RAM and will remain permanent unless you change it again.
N otebook User Guide 6.1 Running the BIOS Setup Program Your computer is likely to have been properly setup and configured by your dealer prior to delivery. However, you may find it necessary to use the computer’s BIOS (Basic Input-Output System) Setup program to change system configuration information, such as the current date and time, or your hard disk drive type. The Setup program can be accessed when you power on the system and pressing the < F 2> function key.
Customizing Your Notebook • 6 Item Specific Help The right side of the screen. This area describes each parameter and its available settings. • Menu Bar The top line of the screen. E ach of the five selections displays its own screen. • Parameters The left side of the screen. This area lists the parameters and their current settings. • Key Status Bar The bottom part of the screen. These lines display the keys available to move the cursor, select a particular function and so forth.
N otebook User Guide 6.2 Using the Main Menu Setup Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help System Time: [10 :54 :32] , , System Date: [06/22/2005] or selects field. 4 SATA Hard Disk [40008MB] CD / DVD Installed System Memory: 640 KB Extended Memory: 2611208 KB CPU Type: Intel ® Pentium ® M processor CPU Speed: 1600 MHz BIOS Version: 0.
Customizing Your Notebook • 6 System Date Allows you to set the system date using the month/date/year format. E nter the current time for reach field and use the < Tab> , < Shift> + < Tab> , or < E nter> key to move from one field or back to another. You can also change the system time from your operating system. • SATA Hard Disk This field display various parameters for the hard disk drive. If type [Auto] is selected, the system automatically sets these parameters.
N otebook User Guide 6.2.1 INTE RNAL HDD SUB-ME NU Phoenix BIOS Setup Utility Main Advanced Security Boot Item Specific Help SATA Hard Disk: [40008MB] Type: Exit [Auto] User = you enter LBA Format parameters of hard-disk Total Sector: 78140160 drive installed at this Maximum Capacity: 40008 MB connection. Multi-Sector Transfers: [16 Sectors] Auto = autotypes Harddisk drive installed here.
Customizing Your Notebook 6 6.3 Using the Advanced CMOS Setup Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Summary Screen [Disabled] Display system Quiet Boot [Disabled] Configuration on boot PXE OPROM [Enabled] F1 Help ÇÈ Esc Exit Å--> Select Menu • Select Item -/+ Change Values Enter Select Sub-Menu F10 Save and Exit F9 Setup Defaults Summary Screen Displays system configuration on boot.
N otebook User Guide 6.4 Security Menu Setup Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Supervisor Password Is: Clear User Password Is: Clear Supervisor Password controls access to the Set Supervisor Password [Enter] Set User Password [Enter] Fixed disk boot sector [Normal] Password on boot [Disabled] F1 Help ÇÈ Esc Exit Å--> Select Menu Enter • Select Item -/+ Change Values setup utility.
Customizing Your Notebook • 6 Set User Password This field is only available when Supervisor Password has set. E nter the user password when boot the system or resume from suspend mode. But if the Write Protect is set in the Fixed disk boot sector field, you should enter a supervisor password to access the fixed disk when boot the system or resume from suspend mode. • Fixed Disk Boot Sector If you set this field to Write Protect, the write protect boot sector on hard disk will protect against viruses.
N otebook User Guide 6.5 Using the Boot Setup This item allows you to set the search drive sequence where the system will try to boot up first. Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Boot priority order: SATS HDD: HUJITSU MHT2040BHT BD Keys used to view or CD \ DVD: HL-DT-ST DVD-RW GCA-4080N configure devices: Excluded from boot order: Up or Down arrows PCI LAN: Broadcom MBA Select a device. <+> and <-> moves the device up or down.
Customizing Your Notebook 6 6.6 How to Exit the Setup Program There are two choices to escape from the Setup program. Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Exit Saving Changes Exit System Setup Exit Discarding Changes and save your Load Setup Defaults changes to CMOS.
N otebook User Guide • Save Changes Saves Setup data to CMOS. • Battery Refresh Conditions the battery so that the battery can be fully charged. 6.7 How to Upgrade the BIOS Your computer uses E PROM Flash BIOS chip that allows you to easily upgrade the BIOS program. When you update the BIOS, any customized settings you made are lost. To upgrade the BIOS: 1. Insert the BIOS Update diskette into the diskette drive. 2. Power on the system with the diskette in the diskette drive. 3.
Customizing Your Notebook 6 107
Using Options 7 7 Using Options T his chapter describes the advanced features and expandable architecture in your notebook. You can upgrade your system for specific requirements.
N otebook User Guide System Upgrade This section provides some steps in doing system upgrade for your notebook computer. The upgrade procedures include the following: 7.1 Memory Upgrade Your notebook computer offers 200-pin SODIMM (Small Outline Dual Inline Memory Module) at least 256MB DDR2-SDRAM. The memory compartment is located inside your computer. The table below lists the possible combinations of different memory module and memory size.
Using Options 7 I NSTALLING ME MORY MODULE Your computer comes with standard 256 MB, 512MB or 1024MB of synchronous DDR2 SDRAM. You can increase system memory to a maximum of 2048 MB in the system, by installing two small outline double inline memory modules (SO-DIMMs) with installed base memory in the system. The 256MB, 512MB and 1024MB memory modules are available: To install the memory module: 1.
N otebook User Guide + Avoid touching the exposed components inside the system. Doing so may damage the system. 5. Insert the connector of the memory module into the socket. Make sure the notch of the memory module fits the nose of the socket. y Hold the memory module at a 30-degree angle and push its connector into the memory socket of the notebook. y Press down on the edge of the memory module until the locking tabs on both sides is locked. 6.
Using Options 7 2. Take out the hard disk from the compartment by finger carefully 3. Remove the connector from the hard disk gently. 4. Remove the crane screws located at each side of the hard disk. 5. Rotate and tighten the crane screws to the new hard disk. 6. Attach the connector to the new hard disk precisely. 7. Place the hard disk back to the compartment. 8. Cover the lid, then rotate and tighten the screws. 9.
N otebook User Guide + Please contact dealer or certified technician for changing the hard disk drive. The damage of changing HDD resulting from users may not be under warranty 7.3 Wireless Module Installation This computer uses mini-PCI wireless LAN module at the bottom of this notebook for wireless connection. + Please contact dealer for adding or changing this module.
Caring for Your Notebook 8 8 Caring for Your Notebook Y our Notebook PC is a fully IBM compatible portable personal computer with the latest features in mobile computing and multimedia technology. Lightweight and compact, your Notebook PC runs on a whole wide range of general business, personal productivity, and professional applications, it is ideal for use in the office, at home, and on the road.
N otebook User Guide 8.1 Important Safety Instructions Portable computers take the most beating from end users. This section gives you detailed information about how to maintain a safe working environment while using the notebook computer. You can maintain its condition and performance by following these guidelines. Please read it carefully to ensure maximum safety. • Before cleaning the notebook computer, make sure it is disconnected from any external power supplies (i.e.
Caring for Your Notebook • 8 While unplugging the power cord, disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cords you may use can support the total current load of all the connected devices. • Though your AC adapter is suitable for universal international voltage, it still requires a stable and continual power supply. Make sure the voltage of the power source when connect the notebook computer to the power outlet.
N otebook User Guide • ⇓ The notebook computer has dropped and damaged. ⇓ The notebook computer has obvious sign of breakage. Do not leave this notebook computer in an environment unconditioned. Storage temperature above 60ºC (140ºF) may damage the notebook computer. • An approved power cord has to be used for the notebook computer’s power supply. For a rated current up to 6A and an equipment weight more than 3 kg, a power cord not lighter than H05VV-F, 2G, 0.75mm2, has to be used.
Caring for Your Notebook 8 8.3 Maintaining the LCD Quality When it comes to screen problems, heat plays a big part. After a good working session, the typical routine is to shut the machine and close the cover. But the display surface - no matter what type it is - and the components inside the computer radiates heat; when you close the cover, you trap the heat against the screen. Leave the computer's cover open for about ten minutes while the heat disperses. Make this a habit.
N otebook User Guide • Use hard disk maintenance programs like Disk Defragmenter of Windows. These reorganize your hard disk by eliminating fragmentation and improving your hard disk access time. • Install a system password in your computer so others won't be able to use the hard disk. 8.5 Battery Care Guidelines The battery pack furnished with the computer requires reasonable care and handling to ensure efficient operation and maximum life.
Caring for Your Notebook • 8 You should always discharge your battery before recharging it on either of these two conditions: first, this is the first time you start to use your battery; second, you had not charge the battery for more than 2 months. To discharge the battery, please execute the "Battery Refresh" function in the BIOS Setup Utility. 8.
N 122 otebook User Guide
System Specification A APPENDIX A System Specification T his appendix gives information on the technical and hardware specifications of your computer. Please note that the information mentioned here may not be exactly the same with your computer as specification is subject to change without notice or modifying this manual. Designed with an advanced modular architecture, your Notebook PC also allows you for several levels of customization and expansion that are previously available only on desktop PCs.
N otebook User Guide P ROCE SSOR U NIT • Intel® Pentium® M Processor Dothan • Above 1.6 GHz CPU • 2MB integrated L2 cache for the processor SYSTE M ME MORY • Two 200-pin memory slots • User-upgradeable to maximum 2GB using 200-pin SODIMM 256MB, 512MB or 1024MB modules • DDR2 –533 SDRAM modules LCD DISPLAY • 15.
System Specification A STORAGE • 2.5” Format 9.
N otebook User Guide KE YBOARD • Full-sized 86/87/88-keys keyboard with Windows systems hot-keys, inverted T-cursor keys, 6 hot keys, 12 function keys, and embedded numeric keypad • Provides international language keyboard F LASH BIOS 512K Flash ROM BIOS for easy BIOS upgrade I/ O P ORTS • 1 x TV-Out Port (S-Video) • 1 x 15-pin VGA port • 4 x Universal Serial Bus (USB 2.0) • 1 x IE E E 1394 port • 1 x 10Base-T/100Base-TX LAN port • 1 x 56Kbps v.
System Specification • A Approximately 3 Hours (for Battery Mark) Battery Life WE IGHT AND DIME NSION • 357(W) x 271(D) x 24 ~ 39(H) mm • Approximately 3.
N 128 otebook User Guide
