User's Manual

®
WIRELESS
MUSIC RECEIVER
Equipped with Bluetooth® Wireless Technology
SYSTEM REQUIREMENTS
Audio device with 1/8” (3.5 mm)
audio jack (speakers, radios, etc.)
Bluetooth® transmitting device (Bluetooth®
enabled phones, MP3 players, etc.)
GETTING STARTED
The RECEIVER has a built-in rechargeable
battery that will last for up to 6 hours when fully
charged. Charge the battery fully with the
provided micro-USB to USB cable before use:
1. Plug micro-USB into RECEIVER charging port.
2. Plug the other end of the cable into any USB A port.
LED COLOR
STATUS
Red Light ON
Charging
Red Light OFF Finished Charging
3. It will take approximately 4 hours
to charge the RECEIVER fully.
LED MICRO USB 1/8” JACK
ON/OFF (3.5mm)
BLUETOOTH
®
PAIR BUTTON
POWER ON
Press and hold the ON/OFF button for 3-5 seconds
to power on, then release the button. The blue LED
will flash for 1 second (you are in standby mode).
POWER OFF
Press and hold the ON/OFF button for 3-5 seconds
to power off. The red LED will flash for 1 second.
PAIRING A BLUETOOTH
®
ENABLED DEVICE
With RECEIVER power off, press and hold
the ON/ OFF button for 6-7 seconds until
red and blue LED flashes intermittently and
two tones sound (you are in pairing mode).
Note: Pairing mode will last 2 minutes. The
RECEIVER will switch to standby mode if no
devices are connected within 2 minutes.
PAIRING WITH BLUETOOTH
®
ENABLED DEVICES
Refer to your phone user’s manual for further information.
1.Place the RECEIVER and device where
they are no more than 1 meter apart.
2. Put the RECEIVER in pairing mode (see Pairing
with a Bluetooth® Enabled Device above).
3. Activate your device’s Bluetooth® function. Set
your device to search for Bluetooth® enabled
devices, choose “BlueFlame“ from the list.
4. When prompted by your device to connect,
select “Yes” (this will vary among devices).
5. When connected, the blue LED will
flash twice every four seconds.
LED
STATUS
Red + Blue
Pairing Mode
Blue every 2 seconds
Standby Mode
Not Connected with device
Blue every 4 seconds
Connected with Device
Red every 20 seconds
Low Power
Need to recharge
Notes:
In standby mode, if no devices can be
connected within 5 minutes, the RECEIVER will
then turn off automatically to save power.
After successful pairing, device and RECEIVER
will “remember” each other, no need to re-pair.
When RECEIVER is turned on, it will automatically
connect to last connected device. If you want to pair it
with other devices, turn off the Bluetooth® function of last
connected device and pair RECEIVER with new device
(see Pairing with Bluetooth® Enabled Devices above).
When RECEIVER is in standby mode and
doesn’t connect to any devices, press ON/OFF
button twice, it will auto connect to last device.
MUSIC PLAYBACK
Connect the RECEIVER to a speaker and a
Bluetooth® enabled music device at the
same time to enjoy music wirelessly.
Music Playback Controls:
PLAY – Press ON/OFF button once
PAUSE – Press ON/OFF button once
Note: Music will automatically pause
when you receive an incoming call.
CARE AND MAINTENANCE
Read the following recommendations before using the RECEIVER.
Do not expose the receiver to
liquid, moisture or humidity.
Do not use abrasive cleaning
solvents to clean the receiver.
Do not expose the receiver to
extremely high or low temperatures.
Don’t dispose of the receiver in a fire,
as it will result in an explosion.
Don’t attempt to disassemble the
receiver as it may get damaged.
If you don’t plan to use the receiver for an extended
period of time, store it in a dry, dust free place.
(a) “CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the product.”
(b) “NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can ra
diate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between
the equipment and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced
radio/TV technician for help.”
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAN ICES-3 (B) / NMB-3 (B)
FCC ID: ZDMBF4090BT
IC: 9200A
-
BF4090BT
Customer Assistance
Phone: [phone]
Email: [e-mail]
Colors and specifications depicted on this guide may vary slightly
from your product. Ages 14+. This product is not a toy.
Blueflame Technologies LLC. 745 Boylston Street. Boston, MA 02116 USA. Made
In China. Blueflame and the Blueflame logo are trademarks of Blueflame
Technologies LLC. The Bluetooth® word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by Blueflame Technologies LLC is
under license. Other trademarks and trade names are those of their respective
owners. © 2013 Blueflame Technologies LLC. All Rights Reserved.
Limited Warranty: blueflamegear.com/warranty
BF4090.M.EF.01
The device has been evaluated to meet general
RF exposure requirement.
The device can be used in portable
exposure condition without restriction.