User's Manual

ManualsBrandsFirmtech ManualsComputers & AccessoriesZIGBEE USB ADAPTER

Zigbee USB

Serial Adapter

ABOUT FZ200BS

Zigbee 2006 Support

USB Interface

4dBi Dipole Antenna Provided

AT Command provided

Summary of content (36 pages)

PAGE 1
Zigbee USB Serial Adapter ABOUT FZ200BS Zigbee 2006 Support USB Interface 4dBi Dipole Antenna Provided AT Command provided
PAGE 2
FZ200BS Manual VERSION 0.1.0 (C) Copyright FIRMTECH Co., Ltd. 2005 All rights reserved The products and operation descriptions contained herein shall be protected by copyright law. Any part or whole of products or operation description shall not be copied, reproduced, translated, nor transformed into readable form by electronic device or machines, without prior consent in writing by FIRMTECH Co., Ltd.
PAGE 3
FZ200BS Manual VERSION 0.1.0 FIRMTECH Co., Ltd. 2005 Room B-606, Ssangyong IT Twin Tower, Sangdaewon-dong, 442-5, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea 462-120 Homepage : www.firmtech.co.kr Marketing Inquiry : contact@firmtech.co.kr Technical Support Inquiry : techsupport@firmtech.co.
PAGE 4
FZ200BS Manual VERSION 0.1.0 What is zigbee? 1. Features of Bluetooth 1) Objectives of Zigbee : To realize Personal Wireless Communication for short distance and slow speed with Low Power consumption and Low Cost, which is based on IEEE 802.15.4 Standard. 2) Frequency in Use : To use ISM(Industrial, Scientific, Medical) Band which does not require any permission to use. - 2.405 ~ 2.480 GHz: 16 channels in all nations (No.11 ~26 channel) 3) Transmission Rate - 2.405 ~ 2.
PAGE 5
FZ200BS Manual VERSION 0.1.0 2. Zigbee operation < Zigbee Mesh network configuration> 1) Coordinator configures the Zigbee Network. Coordinator communicates with Router and End Device. 2) Router expands Network by connecting Coordinator or other Routers. 3) End Device participates in Zigbee network and communicates with Router or Coordinator.
PAGE 6
FZ200BS Manual VERSION 0.1.0 Products overview FZ200BS can configure Zigbee network with low power consumption and low capacity by using Zigbee stack. Serial data transmission via USB interface is available FZ200BS can be used in conjunction with the FZ100BS/FZ750BS/FZ750BC. < Major features of FZ200BS> 1. Zigbee 2006 support 2. Mesh network support 3. USB Interface is configured as easy as installing a USB driver for the serial data input / output available 4.
PAGE 7
FZ200BS Manual VERSION 0.1.0 FZ200BS Overview (1) To configure the Zigbee network, set each device (FZ200BS) to Coordinator, Router and End Device. The initial factory set value of FZ200BS is set to Router. (2) Do not use Broadcast accompanied by a lot of traffic in the Zigbee network unless it is vital to be used. It is not recommended to make a lot of traffic in the Zigbee network because it causes lots of trouble when transmitting data and bothers to set the new route toward target devices.
PAGE 8
FZ200BS Manual VERSION 0.1.0 (4) Coordinator and Router can configure child nodes up to 8 (5) End Devices cannot configure Child nodes Setting FZ200BS to End Devices should be prior to the Zigbee Network Configuration. If you want to change the device type of FZ200BS from Router to End Device in the Zigbee Network, you had better re-configure the whole Zigbee Network in advance. FZ200BS can configure Child nodes after they are set to Routers and participated in the Zigbee Network.
PAGE 9
FZ200BS Manual VERSION 0.1.0 (6) FZ200BS can configure the Zigbee Network up to 4 Depth. (7) FZ200BSC configures the Zigbee Network with one Coordinator. (8) FZ200BS can transmit data by multipath because it supports mesh network. Contribute the Zigbee Network which has multipath. (9) If you input Serial data into FZ200BS, It transmits the Serial data to its target device. (10) FZ200BS has STATUS LED for showing the status of the Device.
PAGE 10
FZ200BS Manual VERSION 0.1.0 through the OK/ERROR LED. (12) FZ200BS has an IEEE ADDRESS and a NETWORK ADDRESS. 64 Bit IEEE ADDRESS is a physical address of FZ200BS. Every device has its own IEEE ADDRESS and the IEEE ADDRESS is not changeable. FZ200BS set target devices by using IEEE ADDRESS. In conclusion, “target device set-up” is an inquiry using IEEE ADDRESS for NETWORK ADDRESS of its target devices FZ200BS has a 16 Bit of NETWORK ADDRESS for the Zigbee Network communication.
PAGE 11
FZ200BS Manual VERSION 0.1.0 ※ < Routing table update of FZ200BS > Routing table is assigned to each FZ200BS after the Zigbee Network Configuration. Below is the Zigbee network status when data is transmitted from Router2 to Router1 to Coordinator. Data is input into Router2, the Router2 transmits the data to Router1, and then the Router1 transmits the data to Coordinator.
PAGE 12
FZ200BS Manual VERSION 0.1.0 ■ List of contents IMPORTANT NOTE: ....................................................................................................................................................... 2 FCC RF RADIATION EXPOSURE STATEMENT:...................................................................................................... 2 1. PRODUCT COMPONENTS .................................................................................................................................
PAGE 13
FZ200BS Manual VERSION 0.1.0 1. Product components Model Name Pictures Q’ty FZ200BS 1EA WE – 2405TO 1EA CD 1EA ※ If you find any of above components is defective, or not included in the package, please contact the seller you purchased.
PAGE 14
FZ200BS Manual VERSION 0.1.0 2. Product Appearance < Figure 2 Details and Dimension of FZ200BS > 3.

PAGE 15

FZ200BS Manual VERSION 0.1.0 4. Dip Switch & Interface Socket 번호 FEATURES ON OFF BASIC SET 1 Do not use - - - 2 Do not use - - - Firmware Download Firmware Download Select Mode Do not use - 3 4 Operation Mode -

NO. Port Description 1 VCC(3.3V) 3.

PAGE 16

FZ200BS Manual VERSION 0.1.0 5. LED Indication / Reset Switch LED State Power LED Power Input Description Red Power LED is lit. Create a network or networks involved in the case, Status LED flashes about Network Creation one second intervals. or Participation Did not create the network or the network did not participate in the case, Status LED blinks rapidly.

PAGE 17

FZ200BS Manual VERSION 0.1.0 6. Product Performance List Specification Zigbee Spec. Zigbee 2006 Specification Support Communication Distance 120 M Frequency Range 2405~2480MHz Sensitivity -98 dBm Transmit Power 6 dBm Input Power 5V Current Consumption 00 mA (Max) Operating Temperature -20 ℃ - +50 ℃ Max Operating Temperature -30 ℃ - +80 ℃ Communication Speed 9,600 bps ~ 230,400 bps Antenna Dipole Antenna (4 dBi) Interface USB 7.

PAGE 18

FZ200BS Manual VERSION 0.1.0 List Initial set value Device Name FZx00 Vx.x.

PAGE 19

FZ200BS Manual VERSION 0.1.0 Program. The signal speed of FZ200BS is basically 115200bps. 9-1. Serial Communication (Hyper Terminal) Program Execute FZ200BS first power ON. Using a USB virtual COM Port FZ200BS By using the device's power is not ON unless you can not run the HyperTerminal. Select [Start][All Programs][Accessories][Communication][Hyper Terminal] in order, and then a window for Connection Set-up comes up. Put a name in the name blank, and click the OK button.

PAGE 20

FZ200BS Manual VERSION 0.1.0 Select each blank as below “Bit/sec: 115200, data Bit: 8, Parity: None, Stop Bit: 1, Flow Control: None”, and click the OK button. Hyper Terminal is executed. Hyper Terminal simply does not show any letters inputted. If you check on “Echo typed characters locally” to get to know what letters are inputted, the Recommends between FZ200BS and Hyper Terminal are mixed up. Do not check this.

PAGE 21

FZ200BS Manual VERSION 0.1.0 9-2. Set-up FZ200BS Device Type Zigbee Device is classified as Coordinator, Router, and End Device by objective of its operation. There should be Coordinator in the Zigbee Network. A Coordinator should exist in a Zigbee Network. Coordinator manages the Network in the Zigbee Network. Router extends the Network in the Zigbee Network. End Device participates in the Zigbee Network using low power consumption.

PAGE 22

FZ200BS Manual VERSION 0.1.0 3. Do not change the Device Type of FZ200BS once the Zigbee Network is configured. ※ It is better to set Coordinator and Router again(Factory Reset) if the Device Type of FZ200BS is changed after the Zigbee Network is already configured. ※ See if the Zigbee Network is configured before resetting FZ200BS to initial set value. The FZ200BS reset automatically participates in the Zigbee Network if the Zigbee Network still exists there. 9-2-1.

PAGE 23

FZ200BS Manual VERSION 0.1.0 (6) If “OK” is output from FZ200BS, reboot FZ200BS by inputting “ATZ”. (7) “END START ERROR” is output at the moment when FZ200BS is rebooted. “END START OK” is output if the Zigbee Network is successfully configured. (8) Now, End Device of FZ200BS set-up is completed. Turn the Power of the End Device OFF, and set other devices. 9-2-2. FZ200BS Router Set-up (1) The initial set value of Device is ROUTER. ※ The initial set value of FZ200BS is ROUTER.

PAGE 24

FZ200BS Manual VERSION 0.1.0 (6) If “OK” is output from FZ200BS by inputting “ATZ”, reboot FZ200BS. (7) “ROUTER START ERROR” is output at the moment when FZ200BS is rebooted. “ROUTER START OK” is output if the Zigbee Network is successfully configured. (8) Now, Router of FZ200BS Set-up is completed. Turn the Power of the End Device OFF, and set other devices. 9-2-3. FZ200BS Coordinator set-up (1) The initial set value of FZ200BS is ROUTER. (2) FZ200BS device and the PC is connected and powered ON.

PAGE 25

FZ200BS Manual VERSION 0.1.0 “ATZ”, reboot FZ200BS. (7) “COORD START OK” is output at the moment when FZ200BS is rebooted. (8) Now, Coordinator of FZ200BS Set-up is completed, and the Zigbee Network is successfully configured. Turn the Power of the Coordinator Device OFF, and set other devices. 9-3. The Zigbee Network Configuration using FZ200BS Try to configure the Zigbee Network after setting the Type for each Device. 9-3-1.

PAGE 26

FZ200BS Manual VERSION 0.1.0 HyperTerminal, FZ200BS will reset. (2) “ROUTER START OK” and “TARGET NON” are output. “TARGET NON” means that FZ200BS has yet to set its target device. If “ROUTER START ERROR” is output, which means that no Zigbee Network is around, reset the Device or check if the Coordinator’s status is okay. (3) Router participates in the Zigbee Network and extends the Zigbee Network. (4) Router can transmit Data. 9-3-3.

PAGE 27

FZ200BS Manual VERSION 0.1.0 With no target device, data transmission cannot be done even if data is inputted. To set a target device, you need to know an IEEE ADDRESS of the Device. 9-4-1. Searching for an IEEE ADDRESS of Coordinator (1) Input “+++” through Serial port of PC while a Device operates. With Inputting “+++”, the mode of FZ200BS(Coordinator) switches from operation mode to AT-command mode. Data transmission becomes possible when FZ200BS is in an operation mode.

PAGE 28

FZ200BS Manual VERSION 0.1.0 (2) FZ200BS outputs a message “TARGET NON”, which means that its target device is not set. (3) Input “+++” through Serial port of PC while FZ200BS operates. “OK” is output. From then, its target device set-up is possible with AT Command. (4) After “OK” is output from FZ200BS “AT+SETTARGET 001551000000000B” through Serial of PC and press “Enter” Key. AT+SETTARGET : It is a command to save the target device’s address.

PAGE 29

FZ200BS Manual VERSION 0.1.0 (1) Coordinator to set up the device's power is ON. After running HyperTerminal, FZ200BS will reset. The Zigbee Network is configured by Coordinator. (2) Router to set up the device's power is ON. After running HyperTerminal, FZ200BS will reset. The Device participates in the Zigbee Network. Its target device is automatically set. A message “TARGET OK” is output. If, “TARGET NON” or “TARGET ERROR” is output, its target device is not set. Do the “9-4-2.

PAGE 30

FZ200BS Manual VERSION 0.1.0 ERROR LED shows its status. 10. FZ200BS Management TIP Refer to the following to configure Zigbee Network properly in terms of data transmission and Controls. 10-1. FZ200BS Device Type Set-up (1) End Device Set-up Set FZ200BS to End Device before Coordinator and Router is set. (AT+SETEND) Turn the power of the FZ200BS OFF. (2) Router Set-up Set FZ200BS to Router before Coordinator is set. (AT+SETROUTER) Turn the power of the FZ200BS OFF.

PAGE 31

FZ200BS Manual VERSION 0.1.0 (1) Turn the power of FZ200BS set to Coordinator ON. (2) Turn the power of Router and End Device which are supposed to make 1 Depth ON. - You can create Devices in 1 Depth up to 8. (3) Turn the power of Router and End Device which are supposed to make 2 Depth ON. - You can create Devices in 2 Depth up to the number of Router in 1 Depth * 8. - Devices are automatically created in 1 Depth if any seats are available in 1 Depth.

PAGE 32

FZ200BS Manual VERSION 0.1.0 If there are a lot of Nodes in the Zigbee Network, set the space of time longer for data transmission between the Nodes, Especially, in case of End Device, great caution is required. (A space of data transmission per 10 Devices: minimum 2seconds) The Shorter the space of data transmission is, the more traffic in the Zigbee Network is caused. Do not change target device too often. When you set or change a target device, data for transmission is more created to get its route.

PAGE 33

FZ200BS Manual VERSION 0.1.0 (2) Sorts of START MESSAGE COORD START OK : A Device starts as Coordinator and the Zigbee Network is configured properly. Thus, data transmission is possible. COORD START ERROR : A Device starts as Coordinator, and the Zigbee Network Configuration is failed. In this situation, a normal Zigbee Network cannot be configured. After initializing the Device to factory set value (AT&F) and set the Device to Coordinator again, Change the Channel used.

PAGE 34

FZ200BS Manual VERSION 0.1.0 See if there is Router participated in the Zigbee Network configured by Coordinator. See if there is Coordinator which has 8 child nodes. See if there is Router which participates in the Zigbee Network and has 8 child nodes. TARGET NON : There is no IEEE ADDRESS of target device saved. In this case, data transmission is not possible. Set a target device to process data transmission. TARGET OK : Target Set-up is properly done by using an IEEE ADDRESS of target device.

PAGE 35

FZ200BS Manual VERSION 0.1.0 START OK”. Target device Se-up is possible afterwards. FZ200BS outputs “ROUTER START ERROR” or “END START ERROR” if there is no Zigbee Network around or the Device cannot participate in the Zigbee Network. Target device set-up is prior to data transmission. Turn the power of FZ200BS ON, and then the Device is participated in the Zigbee Network. If FZ200BS has its target device’s Address, FZ200BS searches if its target device is participated in the Zigbee Network.

PAGE 36

FZ200BS Manual VERSION 0.1.