General Version Retractable Ceiling Fan with Lights Ceiling Fan Installation Instructions Retain this manual for future use. We appreciate the trust and confidence you have placed in us through the purchase of this ceiling fan. We strive to continually create quality products designed to enhance your home.
Table of contents Table of contents 1 Safety Precautions 2 Warranty 3 Pre-Installation Tools needed 3 Installation kit 4 Specification 5 Installation Step 1(Basic assembly of the fan) 6 Step 2 (Ceiling bracket installation ) 8 Step 3 (Receiver and wiring installation) 9 Step 4 (Light cover installation) 10 Step 5(Switch on and ceiling fan works) 10 Remote Control ( Emitter ) Operation 11 TroubleShooting 12 Quick Answers to common Questions 13 Steps of real ceiling fan installatio
Safety Precautions The information contained in the following pages has been prepared to ensure your maximum enjoyment of your fan Please remove the fuse or turn off the circuit breaker to cut off the power before installing the fan. Ensure all electrical connections are in compliance with local laws, regulations and national eletrical codes. If you are not familiar with electrical installation and wiring, please hire a qualified electrician or consult the wiring manual. 1.
Warranty The manufacturer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. The manufacturer warrants the light kit (excluding any glass), to be free from defects in workmanship and material at the time of shipment from the factory for a period of three years after the date of purchase by the original purchaser.
Pre-Installation Installation kit 1H .4.
Pre-Installation Specification A F G H B I C J D E Part Description K AAA 1.5V Quantity Part Description Quantity A Bracket 1 I Receptor 1 B Down rod 1 J Remote control 1 C Canopy 1 K Battery Exclued 2 D 1 E Yoke cover Light cover F Blades 3 G H Body/motor Light kit 1 1 1 .5.
Installation Step 1(Basic assembly of the fan) ① Install the Yoke cover and Canopy. Then insert the fixing pin, push the Hanging ball up, and fix it with screws. ② Pass the cable through the down rod and lock the down rod. screw .6.
Installation ③ Install the Yoke cover and Canopy. Then insert the fixing pin, push the Hanging ball up, and fix it with screws. ④ OK .7.
Installation Step 2 (Ceiling bracket installation and fan into the installed Bracket.) ① Turn off the fan power supply at the circuit breaker box and the wall switch. OFF ② Can be installed on <15º sloped roof. Choose the following installation methods according to the actual situation of the roof. ACCEPTABLE FOR FAN SUPPORT Electrical Outlet Box or Solid wood roof .8.
Installation ③ Snap the basically assembled fan into the installed Bracket. Click! buckle FAN Step 3 (Receiver and wiring installation) ① Connect the wires according to the polarity (the color of the House power cord may be different if the color is the same). AC IN L(Black) AC IN N(White) L For light(Blue) N Neutral(White) ② House Power To Motor U(Pink) V(Gray) W(Red) Put the receiver into the Bracket and arrange the wires .9.
Installation Step 4 ( Light cover installation) Step 5(Switch on and ceiling fan works) ON .10.
Remote Control ( Emitter ) Operation If emitter can not control the fan 1. Please check whether the battery is installed correctly and whether it is charged. If necessary, replace the remote control battery. 2. Please check if there are similar remote control products working nearby, because remote control products of the same frequency will interfere with each other. 3.
TroubleShooting WARNING: Make sure the power is off at the electrical panel box before you attempt any repairs. .12.
Quick Answers to common Questions __________________________________________________________________________ 1. Can the light and fan work separately? Like, can I turn on just the fan without turning on the light and vice versa? Yes,the light and the fan can work separately,controlled by remote control 2. How do you change the blade speed, I cannot get it to change? Use the remote control. Level 1-6 speed adjustment by press 1-6 button. 3. Can this fan be installed on a concrete ceiling? Yes,it can. 4.
Steps of Real Ceiling Fan installation QR code below is vivid installation video and ceiling fan manual of similar ceiling fan with lights. Please scan and refer to below if necessary. Installation Video Fan Exhibition PDF Manual Installation Steps Ⅰ. Down rod installation Ⅱ. Hang the fan to the Ceiling Ⅲ. Connecting wires Ⅳ. Canopy Mount Ⅴ. LED light Assembly ********************************************************************************* Ⅰ. Down rod installation 1. Put the ceiling fan motor as Pic.
Steps of Real Ceiling Fan installation (Pic.2) (Pic.3) 2. Assemble the canopy Pic.4 and coupling cover Pic.5 below to the down rod as Pic.6.Pay attention the canopy and the coupling cover should be back to back Pic.7. (Pic.4) (Pic.5) (Pic.6) (Pic.7) .15.
Steps of Real Ceiling Fan installation 3. Unpack and Collect the wires as Pic.8 and get them passed through the down rod as Pic. 9. (Pic.8) (Pic.9) 4. Insert the down rod to the Fan Motor base.Look at Pic.10 the two holes are not in the same position but the correct action is two holes should be on the same position after completely insert the down rod. (Pic.10) 5. Insert the lock pin.
Steps of Real Ceiling Fan installation (Pic.11) (Pic.12) (Pic.13) (Pic.14) 3. Put the R-shaped Hitch pin into the lock pin in Pic. 15 and tighten the TWO screws in Pic.16.Then pull down the coupling cover Pic.17. (Pic.15) (Pic.16) .17.
Steps of Real Ceiling Fan installation (Pic.17) ********************************************************************************* Ⅱ. Hang the fan to the Ceiling 1. CUT OFF the power supply for SAFTY!!! 2. Fix the mounting bracket Fig.1 for Concrete Ceiling.Mark the location for the ceiling fan first, then drill two holes in the ceiling to aid in securing mounting bracket with TWO expansion screws provided in Pic.18, and secure the mounting bracket to the building.
Steps of Real Ceiling Fan installation 3.Hold the Ceiling fan at the point as Pic.20 and carefully lift to the ceiling and sit the hanger ball to the mounting bracket as Pic.21. Rotate the down rod until the notch on the hanger ball engaged the ridge on mounting bracket in Pic.22&Pic.22a Down rod can not be rotated if the step is done properly otherwise the fan will wobbles when it is working. (Pic.20) (Pic.21) .19.
Steps of Real Ceiling Fan installation (Pic.22) (Pic.22a) ********************************************************************************* Ⅲ. Connecting wires It is a bit tricky yet it would not be issue if you assembled based on the illustration below. 1. Insert the black remote receiver to the inter space up on the mounting bracket as Pic.23. Pic.25 shows how the wires going, connecting white to white,blue to blue,red to red.Just buckle each other in the same color.
Steps of Real Ceiling Fan installation (Pic.25) ********************************************************************************* Ⅳ. Canopy Mount Reorganize the wires Pic.26 and lift the canopy as Pic.27. Attention there is limited room in the canopy so you have to keep all the wires in order to squeeze them into the canopy. Spin the canopy until the two half loose canopy screws are locked in the smaller hole then tighten down the TWO screws as Pic.28. (Pic.26) (Pic.27) .21. (Pic.
Steps of Real Ceiling Fan installation ********************************************************************************* Ⅴ. LED light Assembly 1. Find the LED drive Pic.29.Connect the LED driver to the fan motor,blue to blue,red to red Pic.30,give a couple of twist and screw a cap,finished Pic.31.Put the magnetic side of the the LED to the fan motor Pic.32.Plug the white wire of the LED drive into the LED light at the arrow-marked point as Pic.33. (Pic.29) (Pic.30) (Pic.31) (Pic.32) (Pic.33) .22.
Steps of Real Ceiling Fan installation 2. Attached the LED driver to the fan motor with the magnet. In order to keep the LED driver fixed,please loosen the screw a bit and buckle the LED drive gap in Pic.34. Screw down the screw Pic.35.Spin the lamp shade until is is tight Pic.36. IMPORTANT!!!Please pull down the ceiling fan as Pic.37 until you hear a “Bang” in order to avoid blade scratch the fan motor when they are stretched or retracted.