User Manual Remote Fiber Node (RFN) Multi‐service ruggedized equipment extends carrier services
Remote Fiber Node (RFN) User Manual 1. Limitation of Liability Copyright 2011 Fiber-Span. All rights reserved. No part of this publication, or any software included with it may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, including photocopying, electronic, mechanical, recording or otherwise, without the prior written permission of the copyright holder.
Remote Fiber Node (RFN) User Manual 2. Introduction The FS47 Remote Fiber Node (RFN) is a multi-service equipment designed to extend multiple wireless carrier services such as 700, 800/900 iDEN, Cellular, PCS, AWS, WiFi and WiMAX. The RFN’s unique design allows it to be easily adapted to meet the demands of new generations of communication schemes. All three DAS interface ports are capable of providing a high linear output power greater than 25 dBm per band.
Remote Fiber Node (RFN) User Manual 3. Revision History Version Description Date Author 0.1 Draft release 8‐Mar‐2011 C.M.
Remote Fiber Node (RFN) User Manual 4. Table of Contents 1. 2. 3. 4. 5. 6. Limitation of Liability............................................................................................................. 2 Introduction ............................................................................................................................. 3 Revision History ..................................................................................................................... 4 Table of Contents ...
Remote Fiber Node (RFN) User Manual 12. Maintenance ....................................................................................................................... 27 12.1. Periodic Inspection Checklist ..................................................................................... 27 12.2. Preventative Measure for Optimal Operation ............................................................. 27 12.2.1. Optical Maintenance ......................................................................
Remote Fiber Node (RFN) User Manual 5. Warnings Invisible radiation exits from areas labeled “Aperture” All fibers at both ends of the optical link connected before applying power to either fiber transceiver unit and remote fiber node will prevent exposure. Follow and comply with all site safety policies. Exclamation point denotes attention to statement. Terminate all RF ports with a 50 Ohm load. While in operation do not touch RFN front façade heat sink because surface is very HOT.
Remote Fiber Node (RFN) User Manual 6. Product Overview A Remote Fiber Node (RFN) chassis has 7 compartments that houses a variety of modular plug-in modules, of which their internal components and rear-mount mechanisms are mapped according to operating frequency bands. Chassis inside slots have a mating rear receptacle that provides primary power to the plug-ins as well as the RF Input / Output interface functions. There is no optical interface between any of the plug-ins and the back receptacle.
Remote Fiber Node (RFN) User Manual 6.1. WiFi WiFi is short for “Wireless Fidelity”, and uses IEEE 802.11 specifications with protocols for communicating end-to-end via a wireless network. The WiFi Plug-in has 3 access points each one independently going to antenna 1,2 and 3 with the Channel set to: Access‐Point Position Antenna ID Channel Name Left ANT 1 WiFi Channel 1 Center ANT 2 WiFi Channel 6 Right ANT 3 WiFi Channel 11 For 802.
Remote Fiber Node (RFN) User Manual Although it accommodates both paths, circuitry is kept shielded providing 120 dB of isolation between them which prevents any RF crosstalk. The iDEN uplink has 2 independent internal inputs that combined iDEN 8 and iDEN 9 allocated bands. Downlink last stage output power amplifier accommodates both iDEN 8 and iDEN 9 frequency bands.
Remote Fiber Node (RFN) User Manual Instrument operates in the UL 1710-1755, DL 2110-2155 MHz region. Figure 5 displays Plug-in Cell, PCS, and AWS RF connections in rear which are the same for all three bands. Figure 5 6.4. 700 The 700 Plug-in is a bi-directional service module comprising of uplink and downlink circuitry. Internally it houses all the devices that conditions, filters and amplifies the specified frequency band while rejecting the adjacent family bands operating within the chassis.
Remote Fiber Node (RFN) User Manual 6.5. Cellular The CELLULAR Plug-in is a bi-directional service module comprising of uplink and downlink circuitry. Internally it houses all the devices that conditions, filters and amplifies the specified frequency band while rejecting the adjacent family bands operating within the chassis. Although it accommodates both paths, circuitry is kept shielded providing 120 dB of isolation between them which prevents any RF crossover.
Remote Fiber Node (RFN) User Manual Block Diagram 7.1.
Remote Fiber Node (RFN) User Manual 7.2. Plug-in Figure 8 7.3. System Block Diagram Figure 9 demonstrates a 1 x 4 system link configuration comprising of 4 RFNs and Headend segments that makeup a link, such as OMU, FTU-RF, FTU-E and RIS. RIS is the last F-S equipment interfacing with the end-user Base Transceiver Station (BTS). In this section, an overview is provided of the Headend equipment incorporated as part of a typical RFN application.
Remote Fiber Node (RFN) User Manual Fiber Transceiver Unit – Ethernet (FTU-E) houses the media converter. ??-Write a brief summary.Radio Interface System (RIS) houses all the RF devices that condition, filter, rssi and control gain that is required between the BTS and FTU-RF, in part because an ideal RF level into FTU is 0 dBm and levels from BTS are considerably higher up to 30 dBm.
Remote Fiber Node (RFN) User Manual Figure 11 Note: Service Group (SG) 3 has provisions for WiMAX, pending its release.
Remote Fiber Node (RFN) User Manual DWDM Configuration Tucked in the RFN lower left tier is the Add Drop Multiplex arrangement, housing all the optics and external interface connections. Designated optical channels are ITUs 26,30,34,38 for the downlink (DL) path and ITUs 26, 30, 34 for the uplink (UL) path which are dedicated for the Service Groups (SG1, SG2, SG3) excluding the Ethernet paths. Duplex configuration allows use of the same ITU channels, see Error! Reference source not found..
Remote Fiber Node (RFN) User Manual Beneath the optical housing is a shallow splice tray compartment for the end-user to loop, make interconnections, and secure the fibers.
Remote Fiber Node (RFN) User Manual 8. General 8.1. RF Notwithstanding the specific operating frequency band of each plug-in, circuitry are alike with a 40 dB gain on the uplink path and 70 dB gain on the downlink path. Uplink noise figure is optimized to be lower than 2. Downlink can drive DAS in excess of 25 dBm per band. And In both paths, for tuning, the same attenuator device is implemented that provides 31 dB of range.
Remote Fiber Node (RFN) User Manual Figure 13 Note: Allow for 0.25 dBo loss for every interconnection. FORX discussion On the opposite side, complimenting is the fiber optic receiver (FORX) which converts the optical input to an electrical output for the downlink (DL) path. By also adding an OADM in the receiver side only matching light goes through while rejecting all others.
Remote Fiber Node (RFN) User Manual 8.3. Alarm Monitor and Control Software 8.3.1. PC Requirements 8.3.2. Launch Program 8.3.3. Firmware Revision 8.3.4. General Settings 8.3.5. Username / Password 8.3.6. Default and Status Settings 8.3.7. Block Diagram 8.3.8. Controls 8.3.9. Alarm Settings 8.3.10. Software Windows ( In ascending order insert windows of all the settings in use) Downlink Uplink 8.3.11. 8.4.
Remote Fiber Node (RFN) User Manual 9. Installation 9.1. Mounting The wall or ceiling bolts securing unit must be sufficiently able to carry the weight of the RFN which must be aligned properly balancing weight throughout the supports. While mounting the RFN a platform underneath must sustained all its weight until all the mounting bolts are tighten and secured. See outline section in this manual for bracket hole dimensions and recommended bolt size.
Remote Fiber Node (RFN) User Manual Left Ant 1 Center Ant 2 Right Ant 3 Fibers & Power In Figure 14 Side Access Panel After inserting the 4 fibers through aperture, route two, (DL and UL) fibers inside all the way to the optical stack. See Figure 15 Optical Stack. View is from underneath the RFN bottom access panel. The DL and UL fiber strands are distinguish by their connector type which is SC/APC type, see Figure 16.
Remote Fiber Node (RFN) User Manual 3 Access Point Connections Ethernet Connection Figure 18 9.3. Tools All external screws are the same head type 5-32, for Plug-in slightly longer, at ¾” and side / bottom access panels are ½” pin-in-Hex screw, see Figure 19. Only a single 5-32 Hex hand driver required, see Figure 20 for Plug-in and access panel maintenance. 9.4. Grounding Figure 19 Figure 20 Immediately inside the RFN side access panels are ground lugs to attach incoming ground wires.
Remote Fiber Node (RFN) User Manual 10. General Precautions Do not change the parameters unless instructed to do so by an authorized supervisor and you are a qualified technician to operate instrument. Do not attempt to move product without the proper tools and man power, because product is extremely heavy. Terminate all the RF ports with a 50 Ohm load prior to powering up.
Remote Fiber Node (RFN) User Manual 11. Startup Checklist Confirm all necessary parts accompanied product before beginning installation or operation. 11.1. Equipment List Remote Fiber Node (RFN) fully populated* FS42R-AP-3 FS42R-iDEN-2 FS42R-AWS-5 FS42R-700-5 FS42R-CELL-2 FS42R-PCS-5 *Does not include WiMAX Plug-in. 11.2.
Remote Fiber Node (RFN) User Manual 12. Maintenance 12.1. Periodic Inspection Checklist Perform an On-Site assessment of the wireless coverage for use as a baseline, so that upon reinspecting quarterly or semiannually a comparison is made to ensure peak performance throughout equipment lifespan. Test and keep a record of the insertion loss of all the fiber strands that interconnect with the equipment from end-to-end. 12.2. Preventative Measure for Optimal Operation 12.2.1.
Remote Fiber Node (RFN) User Manual 13.
Remote Fiber Node (RFN) User Manual 14. Specifications 14.1. Electrical Specifications Externally 3 wires (Hot, Neutral, Ground) conduit route through either side (left / right) access panel orifice (Hot, Neutral) go to two in-line breakers that connect to VAC In (range 85-265) power supply, Outputting 28 Volt DC with 600 Watts capability providing power to all the power amplifiers and in part regulated to 48 and 12 Volts for discrete devices.
Remote Fiber Node (RFN) User Manual Item Current (A) FS42R‐AP‐3 FS42R‐IDEN‐2 FS42R‐AWS‐5 FS42R‐700‐5 FS42R‐CELL‐2 FS42R‐PCS‐5 0.81 3.63 4.00 3.18 2.58 2.58 Figure 25 14.2. Mechanical Specifications 14.2.1. Chassis Fully populated (7 Slots) weighs 198 lbs. 14.2.2. Plug-in Plug-in typical weight is 12 lbs. 14.3. Other Specifications Approvals testing in process for IP66 environmental rating. (i.e.
Remote Fiber Node (RFN) User Manual 15. Outline Drawing An outline drawing of the RFN is shown below. Dimensions are in inches [enclosed brackets in mm].
Remote Fiber Node (RFN) User Manual 16. Illustrations 16.1. Internal All plug-in modules are identical in size. Rear DC connections are the same pin-out while RF connections are custom to each plug-in. Figure 26 is the isometric rear view of a plug-in. The downward extended black facade is the heat sink which maximizes surface area, and thus heat transfer. 16.2. External ??-del- Include identification of all the ports. 16.3. Plug-in DC Figure 27 displays the DC connector in rear of all the plugins.
Remote Fiber Node (RFN) User Manual 17. Troubleshooting The RFN is designed and built to provide trouble-free performance without the need for service. If it does not appear to be functioning properly, please follow these troubleshooting steps. 17.1. RF 17.2. Optics 17.3.
Remote Fiber Node (RFN) User Manual 18. Warranty 18.1. General Warranty The RFN carries a standard warranty period of one (1) year unless otherwise indicated on the shipping packages as noted in the purchase order agreement. 18.2. Limitations of Warranty The warranty is limited to the repair or replacement of the defective product. Fiber-Span will decide which remedy to provide for defective components as its own discretion.
Remote Fiber Node (RFN) User Manual 19. FCC Required Statement Manufacturers Notes “Changes or modifications not expressly approved by the manufacturer could “Void” the user’s authority to operate the equipment”. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Remote Fiber Node (RFN) User Manual 20. Glossary dBe unit of measure for RF. dBo unit of measure for Optical loss which translates 1 dBo equals 2 dBe in RF.
Remote Fiber Node (RFN) User Manual 21. Reference Documents -del- Include list of critical loose leaflets documents comprising user manual.
Remote Fiber Node (RFN) User Manual 22.