O P E R AT I N G MANUAL EN FIBARO BUTTON FGPB-101 CONTENTS #1: Description and features #2: Basic activation #3: Adding/removing the device #4: Operating the device v1.
Important safety information ! Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of operating manual. General information about the FIBARO System FIBARO is a wireless smart home automation system, based on the Z-Wave protocol.
#1: Description and features FIBARO Button is a compact, battery-powered, Z-Wave Plus compatible device. It allows you to control devices through the Z-Wave network and run various scenes defined in FIBARO System. Different actions may be triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
#2: Basic activation 1. Press and turn the button counter-clockwise to open the casing. 2. Remove the paper strip underneath the battery. 3. Press and turn the button clockwise to close the casing. 4. Place the device within the direct range of your Z-Wave controller. 5. Set the main controller in (security/non-security) add mode (see the controller’s manual). 6. Click the button 6 times at least. 7. Wait for the device to be added into the system, successful adding will be confirmed by the controller.
#3: Adding/removing the device i NOTE Adding in security mode must be performed up to 2 meters from the controller. i NOTE In case the device is not added, repeat the adding procedure. i NOTE Removing the Button from the Z-Wave network restores all the default parameters of the device. Adding (Inclusion) - Z-Wave device learning mode, allowing to add the device to existing Z-Wave network. To add the device to the Z-Wave network: 1.
#4: Operating the device Operating the Button: 1 click: send action to associated devices (switch on/off by default) and/or trigger a scene 2 clicks: send action to associated devices (switch on maximum level by default) and/or trigger a scene 3 clicks: send action to associated devices (no action by default) and/or trigger a scene 4 clicks: wake the device up and/or trigger a scene 5 clicks: start reset procedure (press and hold for 5s to confirm) and/or trigger a scene 6 or more learning mod
#5: Associations i NOTE Association ensures direct transfer of control commands between devices, is performed without participation of the main controller and requires associated device to be in the direct range. i NOTE Increasing number of associations will increase battery consumption resulting in shorter battery life. Association (linking devices) - direct control of other devices within the Z-Wave system network e.g.
#6: Advanced parameters The Button allows to customize its operation to user’s needs. The settings are available in the FIBARO interface as simple options that may be chosen by selecting the appropriate box. In order to configure the Button (using the HC controller): 1. Go to the device options by clicking the icon: 2. Select the „Advanced” tab. 3. Modify values of chosen parameters. 4. Save the changes. 5. Wake up the device manually to confirm changes (4 clicks).
i NOTE Values of parameter 3 may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure. 3. Associations in Z-Wave network security mode This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st „Lifeline” group.
14. Key Pressed 3 times – command sent to 2nd association group This parameter defines commands sent to devices associated in 2nd association group after a triple click. Available settings: 0 - no action 1 - SWITCH ON 2 - SWITCH OFF Default setting: 3 - SWITCH ON/OFF – alternately 0 Parameter size: 1 [byte] 15. Key Pressed 3 times – value of SWITCH ON command sent to 2nd association group This parameter defines value of SWITCH ON command sent to devices in 2nd association group after a triple click.
23. Key Pressed 2 times – value of SWITCH ON command sent to 3rd association group This parameter defines value of SWITCH ON command sent to devices in 3rd association group after a double click. Available settings: 1-255 - sent value Default setting: 99 Parameter size: 2 [bytes] 24. Key Pressed 3 times – command sent to 3rd association group This parameter defines commands sent to devices associated in 3rd association group after a triple click.
#7: Specifications Battery type: ER14250 ½AA 3.6V Battery life: est. 2 years (with default settings and max. 10 pushes per day) Operating temperature: 0 - 40°C (32 - 104°F) EU standards compliance: EMC 2014/30/EU RED 2014/53/EU RoHS 2011/65/EU LVD 2014/35/EU Radio protocol: Z-Wave (500 series chip) Radio frequency: 868.4 or 869.8 MHz EU; 908.4, 908.42 or 916.0 MHz US; 921.4 or 919.8 MHz ANZ; 869.
#8: Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Note Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules. DGT Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.