Specifications

ManualsBrandsFENIX ManualsElectronicsBC30 V2.0

BC30 V2.0 Bicycle Light

Technical Parameters

ANSI/PLATO

FL1

Burst

High

Med

Low

Eco/EDC

Flash

Output

2200 lumens

1500 lumens

600 lumens

200 lumens

50 lumens

600/50

lumens

Runtime

2.3 hours

6hours

16 hours

50 hours

Distance

187 meters

155 meters

96 meters

56 meters

28 meters

Intensity

8792

candela

5913

candela

2320

candela

780

candela

196

candela

Impact

Resistance

1 meter

Waterproof

IP67

Note: The above specifications are the test results given by Fenix through its laboratory testing

using 2 Fenix ARB-L18-3500 rechargeable Li-ion batteries under the temperature of 21±3°C and

humidity of 50% - 80%. The true performance of this product may vary according to different

working environments and the actual batteries used.

 2 LUMINUS SST-40-N5 LEDs, with a lifespan of 50,000 hours.

 2200 lumens maximum output.

 Powered by 2*18650 rechargeable Li-ion batteries, batteries can be replaced.

 Smart wireless control switch.

 Size: 4.72'' x 1.99'' x 1.25'' / 120 × 50.5 × 31.8 mm.

 Weight: 5.43 oz / 154 g (excluding battery and bicycle mount).

 Battery level indication and low-voltage warning.

Summary of content (6 pages)

PAGE 1
BC30 V2.0 Bicycle Light Technical Parameters ANSI/PLATO FL1 Burst High Med Low Eco/EDC Flash 2200 lumens 1500 lumens 600 lumens 200 lumens 50 lumens 600/50 lumens / 2.
PAGE 2
    Quick-release bicycle mount, easy to assemble and disassemble. Reliable all-metal heat fin; IP67 rated protection. Compatible with Fenix bicycle light helmet holder, can be used on a helmet. Dual Distance Beam System. Operating instruction Bicycle light① Switches Functional switch On/Off Press and hold the functional switch for 0.5s to turn on/off the light. Output Selection With the light switched on, single click the functional switch to cycle through EDC/Eco→Low→Med→High.
PAGE 3
With the light switched on, single click burst switch to enter Burst mode of 2200 lumens, which will last up to 30s. In 30s, single click any switch to exit Burst mode. Note: If the current battery is low, it will light up with the highest brightness supported by the current battery level. Battery replaceable Insert the coin into the back of the wireless switch, rotate the coin counterclockwise to open the battery cover; and then insert the battery, and tighten the back cover clockwise.
PAGE 4
Battery Replacement 1. Rotate the tail cap button according to the direction of the "OPEN" logo, and pull out of the battery case. 2. Insert the battery according to the polarity markings of the battery compartment. 3. Insert the battery case into the light body, and after the battery case is flush with the light body, rotate the tail cap button in the opposite direction of the "OPEN" logo. Mounting Instruction Bicycle light and wireless switch 1. Loosen the screw of the bike mount.
PAGE 5
 Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare. Included BC30 V2.0 Bicycle light, Bicycle mount, Wireless switch, CR1632 button battery, Bicycle mounting shim (thin/thick), Spare O-ring, User manual, Warranty card Warning 1. This light is a high-intensity lighting device capable of causing severe eye damage. Avoid shining the light directly into anyone’s eyes. 2.
PAGE 6
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.