MUSTANG ™ BY GUITAR AMPLIFIERS ADVANCED OWNER'S MANUAL FENDER ®
MUSTANG™ III/IV/V Advanced Manual Introduction This manual is your step-by-step guide to the advanced features found on your Mustang™ III/IV/V amplifier. Turn to page 8 for the Mustang I/II advanced manual. For information on using Fender® FUSE™, Ableton® Live or Amplitube®, please see the separate manuals for each product available at www. fender.com/support. the knob positions will NOT show their actual settings when a preset is first selected.
MUSTANG™ III/IV/V Amplifier Menus Select amplifier models and adjust amplifier settings using the Amp menus. ♫ You can de-select the highlighted amp setting and return to Amp Model selection mode, as a shortcut, by pressing and holding the AMP button. 4. Press EXIT to return to Play mode. Effect Menus Amplifier Models To select Amplifier Models: 1. Press the AMP button. Bypassing Effects 2.
MUSTANG™ III/IV/V Effects tables continued from previous page... DELAY REVERB Mono Delay Small Hall Mono Echo Filter Large Hall Stereo Echo Filter Small Room Multitap Delay Large Room Ping Pong Delay Small Plate Ducking Delay Large Plate Reverse Delay Ambient Tape Delay Arena Stereo Tape Delay Fender '63 Spring The TAP button can be used to "tap in" delay time and modulation rate settings, by rhythmically pressing the TAP button.
MUSTANG™ III/IV/V 2. Press the SAVE button. The SAVE and EXIT buttons should be illuminated. You can press EXIT at this point to cancel the save process. 5. Press EXIT or TAP to exit from the Tuner. Footswitches 3. Turn the DATA WHEEL select a preset destination to overwrite. 4. Press the DATA WHEEL if you want to edit the name of your new preset. Use the buttons to perform the functions listed along the bottom of the screen; turn the DATA WHEEL to select characters.
MUSTANG™ III/IV/V ♫ You can also have a footswitch button assigned to bypass the Reverb effect by adding on the 2-button Mustang footswitch (see Six-Button Footswitching options, below). Tuner Mode—Press and hold the MODE button to activate the Tuner. The screen and the footswitch both will display the same tuner information so that you can look in either place to tune your guitar.
MUSTANG™ III/IV/V on your player, together with the MASTER volume knob, to adjust the auxiliary volume level. Factory Restore & Firmware Update Phones Jack Plug in your headphones, ear buds, or powered speakers to enjoy the Mustang's stereo features. This jack may also be used as a stereo recording output. The amp's speaker is muted when the PHONES jack is used. Effects Loop You can restore your Mustang amplifier to the original factory settings if desired.
MUSTANG™ I / II Advanced Manual Introduction This manual is your step-by-step guide to all the advanced features found on your Mustang™ I / II amplifier. For information on using Fender® FUSE™, Ableton® Live or Amplitube®, please see the separate manuals for each product available at www.fender.com/support.
MUSTANG™ I / II C1 These LEDs are linked to the knob that is being turned C2 Tape Delay Room D1 Tape Delay Large Hall D2 Ducking Delay Small Hall D3 Echo Filter The tables below list the effect selections for each knob.
MUSTANG™ I / II Tuner Button Your Mustang™ amplifier has a built-in Tuner mode that turns the control panel LEDs into a chromatic guitar tuner. To use the tuner: 1. Press and hold the TAP button for 2 seconds. The TAP and EXIT buttons will illuminate. 2. Strike any single string on your guitar and watch the panel LEDs. The Preset LEDs are used to indicate the note of the string being tuned (the top LED "#" indicates if the note is sharp). 3 LEDs indicate fine tuning.
MUSTANG™ I / II Footswitch Factory Restore & Firmware Update Factory Restore Connect a (optional) 1-button footswitch (P/N 0994049000) into the FTSW jack to enable remote selection of your two favorite presets. The LED (next to the FTSW jack) will turn red or green to indicate which footswitch preset is active. To program the footswitch: 1. Select a preset that you want to assign to the footswitch. The preset must not be modified (the SAVE button must NOT be illuminated to proceed to step 2). 2.
部件部件名称 (Part Name) 部分电子元件 部分机器加工金属部件 部分其他附属部件 铅 (PB) x x x 有毒有害物质或元素 (Hazardous Substances’ Name) 汞 镉 六价铬 多溴联苯 (Hg) (Cd) (Cr6+) (PBB) o o o o o o o o o o o o 多溴二苯醚 (PBDE) o o o O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的现量要求以下 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的现量要求 This product is covered by one or more of the following patents: US Pat. 6,222,110 AMPLIFICADOR DE AUDIO IMPORTADO POR: Instrumentos Musicales Fender S.A. de C.V., Calle Huerta # 132, Col. Carlos Pacheco, C.P.
