User Manual

ManualsBrandsFender Musical Instruments ManualsElectronicsWIFI+BT Module

WIFI+BTModul

e

F23BUUM13‐W2

ManualandSpec,revision1.0

ReferenceDocumen

ts

 FN‐LINKF23BUUM13‐W2moduleproductspecification

 FMAWIFI‐FTSW‐USBschematic

Description

TheFenderFMAWIFI‐FTSW‐USBPCBAssemblyisanI/Oboard(WIFIboard)usedinthefamilyof

FenderModularArchitecture(FMA)products.TheboardhasaUSBportwithamicroABconnector,a

FenderFootswitchportwitha¼”phonejackandawirelessmodule.

CircuitDescription

Referringtotheblockdiagram,therearethreemainsectionsofthecircuit:

 FN‐LinkF23BUUM13‐W2module

 USBport

 Footswitchport

CommunicationwiththeFN‐LinkmoduleisaccomplishedthroughaUSBportfromthe18‐pinmain

boardheader.TheWiFiandBluetoothradiocircuitryiscontainedontheFN‐Linkmodule.Thereisno

antennaonthemodulesotheradiooutputfromthemoduleconnectstoanF‐TypePCBantennaonthe

PCBA.TheFN‐Linkmoduleoperatesfroma3.3Vsu pply source on themainPCBthroughthe18‐pin

header.

TheUSBcircuitonthePCBAconsistsofESDprotectioncomponentsandamicroABUSBconnector.

TheFootswitchcircuitonthePCBAconsistsofESDprotectioncomponentsanda¼”phonejack

connector.

FN‐LinkModuleinstallationandUse

TheFN‐LinkmoduleissolderedtothePCBA.PadsonthePCBAmakecontacttothe3.3Vsupply,USB

portandantenna.Allcommunicationbetweenthehostprocessorandthemoduleisaccomplished

throughthemodulesUSBport.Adescriptionofspecificcommands forBluetoothandWiFidriver

developmentisbeyondthescopeofthisdocumentandcanbefoundindocumentationfromRe altek

fortheRTL8723BUWiFi+BTchipelsewhere.

Summary of content (8 pages)

PAGE 1
WIFI+BT Module F23BUUM13‐W2 Manual and Spec, revision 1.0 Reference Documents   FN‐LINK F23BUUM13‐W2 module product specification FMA WIFI‐FTSW‐USB schematic Description The Fender FMA WIFI‐FTSW‐USB PCB Assembly is an I/O board (WIFI board) used in the family of Fender Modular Architecture (FMA) products. The board has a USB port with a micro AB connector, a Fender Footswitch port with a ¼” phone jack and a wireless module.
PAGE 2
Block Diagram
PAGE 3
FMA Main PCB Interface Header All control and power signals come from a connection to a mother board through an 18‐pin, 2mm dual row female header. The pinout for the header is in the table below: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal USB_OTG_DP USB_OTG_DN GNDD FTSW_DAT CHIP_WAKE FTSW_DET HOST_WAKE USB_OTG_5V USB_OTG_ID 3.
PAGE 4
Power Consumption Operating Voltage WiFi mode current BT Board Dimensions 3.3VDC +/‐ 9% 200mA (TX/RX continuous mode) 2.1 mA (idle power saving) 0.1mA (Idle or RF disable mode) 15mA (SCO HV3) 0.9mA (Inquiry and Page Scan) 7.
PAGE 5
FCC Statement: This de vice co mplies with Part 15 of the FCC Rules. Op eration i s subject to t he following two conditions: (1) Th is device may not cause harmful i nterference. (2) Thi s device must accept any interf erence received, i ncluding interference tha t may cause undesired operation. NOTE: This equipment has been te sted and found to comply with t he limits for a Class B digi tal device, p ursuant to Part 15 of t he FCC Rules.
PAGE 6
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM integrator under control of the Grantee.
PAGE 7
IC Notice: This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference. Including interference that may cause undesired operation of the device.
PAGE 8
This device and its antenna(s) must not beco-located with any other transmitters except in accordance with IC multi-transmitte rproduct procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassess ment permissive change. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur. This module isintended for OEM integrator.