PART LIST Check all parts according to the list before assembly . Feel free to contact with us if you need assistance . Self-Tapping Screws (4*30) (PCs) Door Stopper (PCs) Movable door(1 pc) pA Handle(1 pc) Water-Retaining Locating block cap (1 pc) Sliding glass bar(1 pc) Fixed panel piece(1 Gasket(2 pcs) he — Lo émm = 2.
Left Hand Assembly STEP 1:Measure opening for the correct Shower Door size. *For 48" Shower Door your opening should be between 46-48" between the lines *For 60" Shower Door your opening should be between 58-60" between the lines Right Hand Assembly STEP 1:Measure opening for the correct Shower Door size.
Left Hand Assembly STEP 2 1. Measure the bottom length X between the walls, cut sliding glass bar(11) at the right length, make sure the total length of sliding glass bar(11) and fixed panel piece(12) is equal to X. 2. Have fixed panel piece(12) sit on the tile. 3. Have sliding glass bar(11) sit right beside fixed panel piece(12) on the shower base. Right Hand Assembly STEP 2 1.
Left Hand Assembly STEP 3 1.Measure the distance between walls where the Top Rail (18) will be installed. The Top Rail(18) are match 48" or 60" shower door. If the shower area less 48" or cut the Top the side of without hole) For example:If the shower door of you buy is you shower area just 46", so you need cut 2". Correct side to cut Fixed Panel Side Right Hand Assembly STEP 3 1.Measure the distance between walls where the Top Rail (18) will be installed. The Top Rail(18) are match 48" or 60" shower door.
Left Hand Assembly STEP 4 1.The fixed panel piece (12 ) is tightly attached to the sliding glass bar(11) and placed on the shower base.Position the template(13) against the wall, the bottom of the template should be over the fixed panel piece (12 ) and sliding glass bar(11). 2.Use the level to make sure the template vertically straight. Mark the hole position with a pencil. Repeat the process on the opposite side.After marking, remove the movable glass water barrier. 3.
Left Hand Assembly STEP 5 1.Drill a hole on the mark with 1/4" drill bit. 2.Hammer the anchor into the hole. 3.Use one of the 4*30 self tapping screws(2) to secure Rail Wall Connector) onto the wall.Insert self-tapping screw through the larger hole that faces outward. Right Hand Assembly STEP 5 1.Drill a hole on the mark with 1/4" drill bit. 2.Hammer the anchor into the hole. 3.Use one of the 4*30 self tapping screws(2) to secure Rail Wall Connector) onto the wall.
Left Hand Assembly Right Hand Assembly STEP 6 STEP 6 1. Loose door stopper (3) screws with 6mm Allen wrench(14), 1. Loose door stopper (3) screws with 6mm Allen wrench(14), insert each to either end of the top rail(18), screw in screws. insert each to either end of the top rail(18), screw in screws. 2. Loose rail wall connector) screws with 2.5mm Allen 2. Loose rail wall connector) screws with 2.
Left Hand Assembly Right Hand Assembly STEP 7 STEP 7 1.Install the roller . 1.Install the roller . 2.Secure the two rollers (5) onto the movable door (6) 2.Secure the two rollers (5) onto the movable door (6) and move it inside of shower area. and move it inside of shower area. Smm 0 RRR | Hillock RRR \/
Left Hand Assembly STEP 8 1.Install Top rail(18). Screw Rail wall connectable) to Rail Rail wall connectable, then screw tight the connector screw with 2.5mm Allen wrench. @ ww Right Hand Assembly STEP 8 1.Install Top rail(18). Screw Rail wall connectable) to Rail Rail wall connectable, then screw tight the connector screw with 2.5mm Allen wrench.
Left Hand Assembly STEP 9 1. Remove the nut of Fixed panel fastener(17). Then install Fixed panel(16) on Fixed panel piece(12) and push Fixed panel(16) against the fixed panel(16) is on outside, the top rail(18) is on inside). Finally, install One-side strip(15). 2.Remove the nut of Fixed panel assembled Top rail(18) to Fixed panel(16) with Fixed panel the nut use 4mm Allen wrench. 3.
Left Hand Assembly STEP 10 1. Put the door guide(10) between the sliding glass bar(11) and fixed panel piece(12). 2. Please note that door guide(10) side should be aligned with the end of fixed panel . 3. Locate door guide(10) and level sliding glass bar(11) with level, mark the hole position of door guide(10). 4. Take away door guide(10) and mark the hole position of sliding glass bar(11). Door guide close the fixed panel ? a outside view Right Hand Assembly STEP 10 1.
Left Hand Assembly STEP 11 1. Take away sliding glass bar(11) and drill holes on markings. 2. Hammer wall anchor into the hole. 3. Use self-tapping screws(2) to secure sliding glass bar(11) and cover the wall-side screw with locating block cap(9). 4. Secure door guide(10) with self-tapping screws(2) and cover with locating block cap(9). Right Hand Assembly STEP 11 1. Take away sliding glass bar(11) and drill holes on markings. 2. Hammer wall anchor into the hole. 3.
Left Hand Assembly STEP 12 1.Make sure the bottom of the movable door(6) inserts onto the Door Guide(10). 2.Hang the movable door(6) onto the Top Rail(18). Right Hand Assembly STEP 12 1.Make sure the bottom of the movable door(6) inserts onto the Door Guide(10). 2.Hang the movable door(6) onto the Top Rail(18).
Left Hand Assembly STEP 13 1. Try sliding the door to make sure it slides smoothly without having it set too low. 2. Push the door to the wall and make sure it's parallel with wall. 3. Adjust the roller(5). Loose the roller screw(not fully loosed) with 5mm Allen wrench, then adjust door height by tuning its bias adjustment hole with 2mm Allen wrench. movable door too Wall is not straight 3 2mm Pall Eccentric Adjustment Bushing 5mm Right Hand Assembly STEP 13 1.
Left Hand Assembly STEP 14 1.Install the other 2 rollers(5) onto movable door(6). When install ,please let the down 2 rollers close the top rail(18) . Right Hand Assembly STEP 14 1.Install the other 2 rollers(5) onto movable door(6). When install ,please let the down 2 rollers close the top rail(18) .
Left Hand Assembly STEP 15 1. Assemble bumper strip(4) to wall-side movable door(6). 2. Assemble water-retaining gaskets(8) one each to movable door(6) and fixed panel(16). Right Hand Assembly STEP 15 1. Assemble bumper strip(4) to wall-side movable door(6). 2. Assemble water-retaining gaskets(8) one each to movable door(6) and fixed panel(16).
Left Hand Assembly STEP 16 1.Install the Handle (7) onto the movable door(6) by unscrewing the screws that are attached to the door handle and reinserting through the panel back into the handle. Tighten with the 2mm Allen Wrench. Right Hand Assembly STEP 16 1.Install the Handle (7) onto the movable door(6) by unscrewing the screws that are attached to the door handle and reinserting through the panel back into the handle. Tighten with the 2mm Allen Wrench.
Left Hand Assembly STEP 17 1. Push movable door(6) towards left and stops it until 40mm distance from handle(7) to edge of fix panel(16). 2. Loose the screw of door stopper(3) at fixed panel(16) side and move it until it's side by the roller, re-secure the door stopper(3). 3. Push movable door(6) towards right until bumper strip(4) hits wall, loose the screw of door stopper(3) and move it until it's side by the roller, re-secure the door stopper(3).
Left Hand Assembly STEP 18 1. Use clear silicone on both sides of shower door as well as the door bottom build. Let silicone dry for 24 hours before using the shower. Right Hand Assembly STEP 18 1. Use clear silicone on both sides of shower door as well as the door bottom build. Let silicone dry for 24 hours before using the shower.