Smartlife Instruction Manual of Smart life App POWERSTRIP/WIFI 智能生活应用指导手册
Caution Smartlife This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inteence received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Caution: Radio Standards Specification RSS-Gen, issue 5 - English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
NO.
NO.2 Sign in App 登录应用程序 Smartlife Use the phone number + verification code login or mailbox login使用手机号+验证码登录或邮箱登录 1.Select your country code, enter the cellphone number and tap “Get” to get a message containing verification code 1.选择您的国家代码，输入手机号码，然后点击 “获取”以获取包含验证码的消息 2.Enter the verification code in the message and tap “Login” to login the App 2.
NO.3 Register an account 注册账号 Smartlife If there is no public account does not want to use mobile phone authentication login b can use the mailbox and mobile phone to register account如果没有公用账号也不想使用 手机验证登陆可以使用邮箱和手机进 行注册账号 1.Fill in the phone number and mailbox number 1.填写手机号和邮箱号 2.Use the phone to register requires a verification code and password, mail registration does not require verification code 2.
NO.4 Add device 添加设备 Smartlife 1.Go to the App, tap “Add device” at the bottom, as shown in the picture 1 转到应用程序，点击底部的“添加设备”，如图1所示 2.
NO.5 Add device 添加设备 Smartlife 1.There are two connection methods for the App (hotspot mode and quick connect mode). The quick connect mode is the default mode. Users could tap the upper right corner to switch the connection method to hotspot mode.
NO.6 Add device 添加设备 Smartlife 1. For quick connect mode, please make sure the device’s instructor light quickly flashes 对于快速连接模式，请确保设备的指导灯快速闪烁 2. For hotspot mode, please make sure the device’s instructor light slowly flashes 对于热点模式，请确保设备的教练指示灯缓慢闪烁 3.
NO.7 Smartlife Add device 添加设备 Device status confirmation 设备状态确认 1. Confirm that the device status is flashing after confirming Figure 1 1.确认设备状态处于快闪后确认图1 2. 1. Re-confirm the status of the device after the flash is checked as shown in Figure 2 2.
NO.8 Smartlife Add device-Quick connect mode添加设备 - 快速连接模式 1、Please confirm wifi account is their own home name and enter the corresponding network password picture 1请确认wifi的账号是自己家名称并输入对应网络的密码图1 2、For quick connect mode, the App interface will go through the changes during the network configuration process as shown in the picture 2.
NO.9 NO.3 Smartlife Add device-Hotspot mode添加设备 - 热点模式 1.When the current internet status is unstable, App interface will be shown as in the picture 1当当前 Internet状态不稳定时，App界面如图1所示 2.Long press device’s reset button for 5 seconds or longer until the device’s Wi-Fi instructor light slowly flashes, as shown in the picture 2 2.长按设备的复位按钮5秒钟以上，直到设备的Wi-Fi指示灯慢慢闪烁，如图2所示 3.
NO.10 NO.3 Smartlife Add device-Hotspot mode添加设备 - 热点模式 1. For hotspot mode, the device’s instructor light slowly flashes, tap “Confirm reset, switch to hotspot mode” and go on to the next step对于热点模式，设备的指示灯慢慢闪烁，点击 “确认复位，切换到热点模式”，进入下一步 2.
NO.11 NO.3 Smartlife Add device-Hotspot mode添加设备 - 热点模式 The App interface will go through the changes as shown in the picture 1.
NO.12 Control device 控制装置 Smartlife After the device is connected successfully, tap “Devices” at the bottom. The device name shows in the list. Tap it to enter the control panel of the smart socket设备连接成功后，点 击底部的“设备”。 设备名称显示在列表中。 点击它进入智能插座的控制面板 Remarks: When device is online, there will be a green dot at the front of the device icon; When the device is offline, the dot will be grey; If is the device shared by others, there will be double loop.
NO.
NO.14 Smartlife Control device 控制装置 1, click on the middle of the middle button to jump to Figure1 can be 5 respectively on the control port timing点击下方中间的按键跳转到图1可以分别对5个控制口进行分别定时. 2, the timing of the two groups of data corresponding to hours and minutes, repeat the option is to select the date of the date, every day to check all, open and close the option is completed after the corresponding turn on or off.
NO.15 Profile 简介 Smartlife “My profile” is where users could manage personal information. The key information is as follows: “我的个人资料”是用户可以管理个人信息的地方。 关键 信息如下： 1.Personal information：Including account name and cellphone number个人信息：包括帐号和手机号码 2.Information of shared devices共享设备信息 3.Message center消息中心 4.Entry to submit feedback提交反馈意见 5.F.A.Q常问问题 6.Phone binding: if you sign in with social network account, you could bind your phone number with your account 手机绑定：如果您使用社交网络帐户登录，则可以将您 的电话号码与您的帐户绑定 7.
NO.16 Profile 简介 Smartlife Add sharing: As shown in the picture, users could type in a new member’s cellphone number and share the device with him. The new member could control the device with his own account.
NO.17 Profile 简介 Smartlife Sharings sent: The list shows all members who are added by your account. You can delete the member and cancel the sharing by sliding to left.
NO.18 Profile 简介 Smartlife If you sign in with social network account, you need to bind a cellphone number in order to share devices with others. The interface is as shown in the pictures below.
NO.19 Profile 简介 Smartlife 1.Tap “rate us”, App will jump to a corresponding Application market, where you could rate us 2.Show privacy policy 3.Show App version number 应用程序将跳转到相应的应用程序市场，您可 以在此评价我们 2.隐私政策 3.
Smartlife Thank You Remark： 1) The pictures used in this manual are iOS App interface, Android version is a bit different 2) Product and software update periodically, the number and App interface in this manual are only for example.
