Reference Test report no. 17010758 EUT: ID ISC.ANT1520/700 (RFID gate premium) IC: 6633A-LRM2500 RSS-210 Issue 9 Date of issue: 2017-03-27 Annex acc. to RSS-210 Issue 9, August 2016 relating to FEIG ELECTRONIC GmbH ID ISC.ANT1520/700 (RFID gate premium) Annex no. 5 User Manual Functional Description RSS-210 Issue 9 RSS-Gen Issue 4 RSS-102 Issue 5 Date: 2016-11-11 m.
INSTALLATION ID ISC.ANT1520/700-HPD Type A and B / RFID gate premium Version: Reader ID ISC.LRM2500-B draft – custmized (E) 2017-03-14 –ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-ID-E.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Note Copyright 2017 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB General information's regarding this document • The sign "" indicates extensions or changes of this manual compared with the former issue. • If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or for internal testing- and manufacturing-functions. These bit spaces must not be changed, as this may cause faulty operation of the reader. • The following figure formats are used: 0...9: 0x00...0xFF: b0...
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Contents 1 Safety Instructions / Warning - Read before Start-Up ! 7 2 Instruction on transportation and shipping of the antennas 8 3 Maintenance 9 4 Performance Features of the ID ISC.ANT1520/700 Antennas 4.1 5 6 10 Delivery contents ...................................................................................................... 11 4.1.1 Antenna ID ISC.ANT1520/700 Type HPDA ....................................................
IDENTIFICATION ID ISC.ANT1520/700-HPDA/-HPDB 6.4.2 Reading a Serial Number ....................................................................................... 43 6.4.3 Testing the performance ........................................................................................ 44 6.5 7 Installation Setting the Alarm Indicators (Alarm Buzzer and Alarm LED lights) ...................... 46 6.5.1 Setting the Alarm Buzzer ........................................................................
IDENTIFICATION 10 Installation Annex A ID ISC.ANT1520/700-HPDA/-HPDB 87 10.1 Terminal assignment “Terminal Board”.................................................................. 87 10.2 Internal wiring ........................................................................................................... 88 FEIG ELECTRONIC GmbH Page 6 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 1 Installation ID ISC.ANT1520/700-HPDA/-HPDB Safety Instructions / Warning - Read before Start-Up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries.
IDENTIFICATION FEIG ELECTRONIC GmbH Installation Page 8 von 92 ID ISC.ANT1520/700-HPDA/-HPDB ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 2 Installation ID ISC.ANT1520/700-HPDA/-HPDB Instruction on transportation and shipping of the antennas The packaging of the antennas has been designed to transport antennas vertically standing on a pallet to the site of installation. Attention! The antenna has be transported vertically on the base side on the pallet. A transporting or storing in the false orientation can cause damaging at the antenna.
IDENTIFICATION 3 Installation ID ISC.ANT1520/700-HPDA/-HPDB Maintenance The antenna ID ISC.ANT1520/700 is a design product with high quality surfaces, and should always be handled with caution. The antenna was designed to work reliably and flawlessly for years without special maintenance. Attention! The surfaces should be cleaned with a clean, soft cloth dampened in a dishwashing liquid – water solution.
IDENTIFICATION 4 Installation ID ISC.ANT1520/700-HPDA/-HPDB Performance Features of the ID ISC.ANT1520/700 Antennas The ID ISC.ANT1520/700-HPDA antenna is a version with integrated Dynamic Antenna Tuning Boards ID ISC.DAT , Long Range Reader ID ISC.LRM2500-B, 8-times Multiplexer Module ID ISC.ANT.MUX.M8, additional Alarm LED light and Alarm buzzer . Additionally, one People Counter, one radar Detector and LCD Display are already integrated in the antenna ID ISC.ANT1520/700-HPDA. The ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 4.1 Delivery contents 4.1.1 Antenna ID ISC.ANT1520/700 Type HPDA • • • • • Antenna ID ISC.ANT1520/700-HPDA including 2 dynamic antenna tuner Long Lange Reader Module ID ISC.LRM2500-B 8 Channel Multiplexer Module ID ISC.ANT.MUX.M8 Power Supply ID ISC.Net24V-B 100-240V/ 24V People Counter ID ISC.ANTGPC 4.1.2 Antenna ID ISC.ANT1520/700 Type HPDB • • • Antenna ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 4.2 Performance Features of the People Counter ID ISC.ANT.GPC The product ID ISC.ANT.GPC, short form “Gate People Counter” or “GPC”, are made for mounting in the gate antennas ID ISC.ANT1520/680 and ID ISC.ANT1520/700 and. A Gate People Counter consist of a People Counter board (PC) and one Radar Detector! The product ID ISC.ANT.GPC-E2 Extension Radar Detector is used to extend the People Counter to a second gate aisles.
IDENTIFICATION Installation Radar detection zone of a single gate ID ISC.ANT1520/700-HPDA/-HPDB Radar detection zone with two aisles Counter 1 | Counter 2 In | Out Cnt. 1 | Cnt. 2 In | Out Cnt. 3 | Cnt. 4 In | Out Radar detection zone with three aisles Cnt. 1 | Cnt. 2 In | Out Cnt. 3 | Cnt. 4 In | Out Cnt. 5 | Cnt. 6 In | Out Fig. 2: Top view of the detection areas (2-4 antennas, 1-3 gate aisles) The People Counter board and the Radar detectors are mounted in the base of the antennas.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 4.3 Available Antenna Types The following products are currently available: Antenna Type Description ID ISC.ANT1520/700HPDA Crystal Gate Antenna with Reader, Multiplexer , two dynamic tuning boards ID ISC.DAT, signal light, alarm buzzer and People Counter Board, one radar detector and LCD Display. ID ISC.ANT1520/700HPDB Crystal Gate Antenna with two dynamic tuning boards ID ISC.DAT and signal light ID ISC.ANT.
IDENTIFICATION 5 Installation ID ISC.ANT1520/700-HPDA/-HPDB Installation and Wiring Notes: Before installing the antennas please read 6.1 Project Notes Antenna. The spacing of the antennas in a gate depends on the antenna configuration. If multiple antennas or gates are connected to different readers, a minimum clearance of 8 m must be kept between the antennas or gates. For shorter distances (1 m – 8 m) the readers must be synchronized.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 5.1 Mounting Preparation For the assembly of the antenna it has to be carefully unpacked and the antenna base to be opened. This is done as described in the following steps: 1. Place the packed antenna on the floor with the top side facing up. Carefully open the box and then remove the antenna. Fig. 3: Packed Antenna 2. Afterwards, the antenna has to be placed carefully on the floor again.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 5.2 Installing the antenna 5.2.1 Dimensions of antenna The overall dimensions of the antenna are shown in Fig. 5 Fig. 5: Antenna outside dimensions All dimensions are in mm with general tolerance according to ISO 2768 m (mean). FEIG ELECTRONIC GmbH Page 18 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 5.2.2 Drilling the Mounting Holes If the position of the antennas has been marked or determined, the mounting holes and the holes for the cable entry, can be marked and drilled. To make this easier the ID ISC.ANT.CRG-DT Crystal Gate Drilling Template could be used.(optional). This Drilling template could also be used for stabilization and weight distribution on soft grounds by mounting it additionally under the antenna foot.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB A cable opening is provided for the necessary connection cable (see Fig. 6). The cable opening is dimensioned such as up to 10 cables having a diameter of 6 mm can be passed through the opening. Alternatively the cables can be routed at the sides of the antenna bas like shown in Fig. 7 Fig. 7 Cable routing at the antenna sides FEIG ELECTRONIC GmbH Page 20 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 5.2.3 Installing the Antenna Base and Antenna Body The antenna will be mounted on the floor. Please note, the antenna conductors in the middle of the antenna body have to have the same direction (Fig. 8). Afterwards, the antenna has to be aligned the antenna vertically, by using the adjusting screws (Fig. 9). Please read also 6.8.4 Using the trigger function of the Gate People Counter.and 6.2 Project Notes People Counter (GPC). Fig.
IDENTIFICATION 6 Installation ID ISC.ANT1520/700-HPDA/-HPDB Typical Antenna Configuration (Gate Antenna with two Antennas) The standard configuration of a gate with three-dimensional tag orientation consists of one ID ISC.ANT1520/700-HPDA with reader and multiplexer and one ID ISC.ANT1520/680-HPDB. If a tag moves, at horizontal line, through the gate, it can be read at least once. This ensures high reliability of the antenna system. 6.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB If multiple gates are arranged with short distances (1-8m) between each other, these will mutually interfere with each other. In this case, the readers for the individual gates have to be synchronized and run in one of the automatic modes. Y X X Y Fig.
IDENTIFICATION Installation Transmitted ID ISC.ANT1520/700-HPDA/-HPDB Minimum Distance output power < 0.5 W 1m 0.5 W-1.0 W 2m 1.1 W – 2.0 W 3m >2W 4m >= 4 W 8m Table 4: Minimum Distances - There should be no interference of the Reader from other electrical devices in the environment. The Noise Level difference should be less than 20 mV. - The ID ISC.LRM2500 reader should be set to an RF power of 4 watts. - When using ISO 15693 transponders, the Readers should be set as described in 6.3.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.2 Project Notes People Counter (GPC) The radar sensor of the People Counter detect moving objects within the detection area / beam (A1, A2, see Fig. 12) of the radar antenna. The size of the detection area, and hence the sensitivity of the devices can be adjusted with jumpers JP1 and JP2 A door (including glass doors), a curtain and in particular automatic doors or other moving objects can influence the counting of the People Counter much.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB That means, the antennas are installed close to the entrance and exit, the detection area of the radar sensors must show away from the door. Otherwise, a minimum distance of 1.0 m between moving objects and detection areas must be guaranteed. door wall / masonry . Antenna Type -A Typ -B wall / masonry Typ -B A1 B A2 C A D Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB At distances D > 140 cm, reduce the accuracy of the systems. If two people (or moving objects) move, simultaneously, in the detection area of one radar sensor, usually, is counted one person, only. The minimum distance between two people, so that these people are detected separately, as a function of the adjusted sensitivity and position in the passage is 60 cm to 130 cm. Cross traffic in the detection area, i.e.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3 Gate Configuration and Setup using Antennas 6.3.1 Required Components To set up the gate you need the following components: - Qty. 1 ID ISC.ANT1520/700-HPDA Crystal Gate (Base) (incl. Qty. 1 ID ISC.NET24V-B Power Supply Unit) - Qty. 1 ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3.2 Configuration of a Gate Antenna with Multiplexer Connect the components as shown in Fig. 13 . Almost, all cable should be mounted already. Normally, the antenna cables from antenna Type HPDB has to be connected to OUT3+4 at the multiplexer (See also 6.3.3 Setting the Multiplexer) and the 24V DC power supply to X11 of the terminal board only.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Fig. 15: Terminal board An overview of the terminal board assignment is given in 9. Annex A Note: • A reverse polarity could damage the device or the In-/Outputs. The connection between Antenna Type A and Type B must be made with the data cable which is content of the Antenna Type B. The ferrite core should have 3 turns of the cable approx. 7cm at the cable end. • FEIG ELECTRONIC GmbH Fig. 16: Terminal board Page 30 von 92 ID ISC.
IDENTIFICATION FEIG ELECTRONIC GmbH Installation Page 31 von 92 ID ISC.ANT1520/700-HPDA/-HPDB ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Find here a possible wire connection between antenna Type HPDA and HPDB At a single gate with 2 antennas a connection between X13 GPC-out of the terminal board in Antenna Type HPDA and X13 GPC-out of the terminal board in Antenna Type HPDB must be installed. The side with the ferrite core must be placed in the antenna Type HPDB. 1. People Counter ANT1520680-HPDA LED-light ANT1520680-HPDB Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB The coax cables have fixed lengths and may not be shortened and therefore need to be tied into small loops (see Fig. 17). Tie all cables as far away from the antenna conductor as possible. The cables must never be allowed to contact the antenna conductor. Unused cable length (e.g. of interface cable) should not be placed in the area above the reader and multiplexer. The power supply should not be placed in the type HPDA antenna.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Fig. 19:Connection of the components in an antenna Type HPDA FEIG ELECTRONIC GmbH Page 34 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB The cable from antenna type HPDB to the antenna type HPDA should preferably be connected shortly. Unused cable lengths are possible should be tied in antenna B type. Tie all cables as far away from the antenna conductor as possible. The cables must never be allowed to contact the antenna conductor. It is possible to place the power supply in foot of the antenna type B. Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3.3 Setting the Multiplexer The jumpers JP11-JP18 should be set (factory setting) as shown. More on setting the ID ISC.ANT.MUX.M8 Multiplexer can be found in the corresponding installation manual (M90700-xde-ID-B). 4. ANT Upper Loop 3 ANT Lower Loop Upper Loop 1. ANT Lower Loop Lower Loop 2 ANT Upper Loop Lower Loop Upper Loop Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3.4 Setting the Antenna Tuner For checking the settings of the antenna tuner the antenna base has to be opened. For this the two fastening screws (hexagon socket width AF 2,5) have to remove of the antenna base cover. By moving the cover upwards, carefully, remove the cover from the antenna base. Step 1 Step 2 Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3.5 Interface Connections 6.3.5.1 LAN / TCP/IP The Reader has an integrated 10 / 100 Base-T network port for an RJ-45. Connection is made on X1 and has an automatic “Crossover Detection” according to the 1000 Base-T Standard. X1 Fig. 23: LAN interface for host communication With structured shielded cabling CAT-5 cables should be used. This ensures a reliable operation at 10 Mbps or 100 Mbps.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.3.6 Reader Configuration with Multiplexer To tune the antennas, open the ISOStart software and read out the current configuration of the Reader: Step Action Note Start ISO Start Software 1 Select „Detect“ 2 Select „Run without change“ Note: 3 This has to be done at each start of ISO-Start program otherwise the configuration of the reader will be changed by the wizard.
IDENTIFICATION Step Installation Action ID ISC.ANT1520/700-HPDA/-HPDB Note Select „Expert Mode“ and confirm with OK. 5 Select “Logical View” 6 FEIG ELECTRONIC GmbH Page 40 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Afterwards set the operating power, Transponder Parameters and ISO Host Mode: Step 1 Action Note Select “Configuration” Air Interface: “Output -Power” = 4W „Multiplexer Enable“ „1 Input (Single Mode)“ „No of Output Channels „ 2 (4 = one aisle) (6 = two aisles) (8 = three aisles) „Antenna Active Time“ 100 x 5ms “Receiver Channel” Upper and Lower Sideband 3 Set by clicking on „Apply“.
IDENTIFICATION Step Installation Action ID ISC.ANT1520/700-HPDA/-HPDB Note Operating Mode: 6 For antenna tuning the reader has to be set to „Host Mode“. 7 Set by clicking on „Apply“. 6.3.7 Tuning the Gate Antenna Before tuning the gate antenna, you must quit the ISOStart software. Then the gate can be tuned as follows: Step Action Note Start “DATuningTool” software 1 Select “Detect Reader...”. 2 In the „Detect Reader“ window select the interface (COM-Port 1, BusAdr.
IDENTIFICATION Step 6 Installation Action ID ISC.ANT1520/700-HPDA/-HPDB Note If this does not succeed on the first try, start the process again by clicking on „Start Tuning“ After successful tuning, close the DATuningTool. FEIG ELECTRONIC GmbH Page 43 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.4 Testing the Gate Antenna After tuning the gate antenna, you can check for proper function using a reader, the ISOStart service software and a Transponder. Here the Noise Level and performance of the gate are tested. 6.4.
IDENTIFICATION Step Installation Action ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.4.2 Reading a Serial Number Step 1 Action Note Attach a tag to an antenna Use adhesive tape, for example Here to antenna at multiplexer output 1 Activate antenna 1 with command: „Function Unit Commands - Multiplexer“ 2 Parameter: „Channel Select“ „Cascade Level = 1“ „Output Channel of Input 1 = 1“ 3 Confirm with “Send” 4 Select „Test and Measurement“ 5 Select „ISO Inventory“ function and activate by clicking on „Start“.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.4.3 Testing the performance For testing the performance you must switch the reader to one of the Automatic Modes. See 6.6 Activating the Automatic Mode A read transponder will be displayed by a blue LED on the reader, the Alarm LED light of the antenna and the Alarm sounder. See also 6.5.1 Reader Setting for Alarm Indicator In this test the capture area of the gate antenna described in 6.1 Project Notes is checked.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB If one or more „holes“ are detected, check the noise values on the Reader (see 6.4.1 Checking the Noise Level). The following may result in faulty readings: • Antenna improperly installed (orientation, antenna distance, check cabling) • Metal near the antennas is detuning or interfering with them. • The antennas are not properly tuned.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.5 Setting the Alarm Indicators (Alarm Buzzer and Alarm LED lights) 6.5.1 Setting the Alarm Buzzer The solution provided here presumes that the alarm indicator (buzzer) is switched through the digital output 2 /X2 on the ID ISC.LRM2500-B reader. The pulse duration can be set (CFG2 / OUT2) between 100 ms and 65535 s by adjusting the Reader configuration. The volume of the buzzer could be adjusted by R1 Fig. 25 Configuration Buzzer Fig.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.5.2 Setting the LED´s The alarm LED´s will be switched by a command of the reader over the RS485 Bus. Due to that reason the terminal boards of all used antennas have to be connected 1:1 in parallel together. The Bus address for each LED will be defined by the antenna number it is installed in. The antenna number depends on the output of the Multiplexer the antenna is connected to.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.5.3 Reader Setting for Alarm Indicators The ISOStart software can be used to set the Reader configuration so that the output 2 X6-1/-2 opens or closes or the outputs of the People Counter closes when a Transponder is read. Step Action 1 Start ISOStart Software 2 Select “Configuration” and click on “Read” to read the complete configuration. Note Operating Mode 3 Select Buffered Read Mode.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Assign LED Bus Address 11 to antenna 1. LED Bus Address 12 to antenna 2. ......... and so on. „True“ means: LED with Bus Address 11, 12, 13, 14 will be active if the reader read a valid transponder on the corresponding antenna 7 Set by clicking on „Apply“.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.5.4 Programming a Transponder with the AFI Byte If the Transponders will remain on the object when leaving the storage location, they must first be disabled. This is generally done by writing to a particular area of the Transponder. The AFI byte (Application Family Identifier) is useful for this purpose, since it is contained in nearly all Transponder models in the ISO15693 family.
IDENTIFICATION 7 Installation ID ISC.ANT1520/700-HPDA/-HPDB To verify, read AFI byte by using the command [0x2B] Get System Information FEIG ELECTRONIC GmbH Page 54 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.6 Functions of the LCD-Display Only in the Automatic Modes (Scan, Notification or Buffered read Mode) the Display will work as described. After power up the antenna type HDPA or the command “System Reset” the Display will show: Step Description 1 Means reader is not in one of the Automatic modes after power up.. Display Please set reader to one of the Automatic Modes.
IDENTIFICATION Step Installation Description ID ISC.ANT1520/700-HPDA/-HPDB Display The sum of the all counted people (IN+OUT) till now. 7 8 Then the counter values for IN and OUT After that the display will change between ALL and IN /OUT values The Counter values in the display will be updated every 30 seconds ! 5 seconds 9 The counter values could be Reset with a paper clip by pressing the Reset Button under the hole beside the Display. 10 Press the Reset Button till the Reset process starts.
IDENTIFICATION Installation Step Description 12 After the Reset process the display will start again to show the values. 13 ID ISC.ANT1520/700-HPDA/-HPDB Display If an error occurs the Error Code will be shown together with the ALL values. The mean of the Error Code will be shown in table 10.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.7 Activating the Automatic Mode The gate has to be used in one of the Automatic Modes (Buffered Read, Notification or Scan Mode) to get a maximum performance. Otherwise the reading performance will be significantly reduced. For more information, see System Manual H01112-2e-ID-B.pdf ID ISC.LRM2500-A/B Which mode the most suitable is for your application has to be defined in advance.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.8 Automatic Bus addressing The automatic bus addressing should be done after setup, configuring and tuning the gate antennas.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 6.9 Installation ID ISC.ANT.GPC-E2 2. 4. 3. 1. 3. Content of the ID ISC.ANT.GPC-E2 1. 1 piece Radar connection cable 2. 1 piece Radar module 3. 2 piece spilt rivet 3,0mm 4. 1 piece cable-clip Step Action Note Attention !! 1. Note: Do not touch the antenna surface of the Radar module to avoid damaging the electronic components and soiling. Connect radar connection cable with X1 of Radar module. 2.
IDENTIFICATION Installation 3. Plug Radar connection cable into X12 Sen 2 and fix the cable with the cable clip. 4. Install Radar module with split rivet ID ISC.ANT1520/700-HPDA/-HPDB See also picture in Step 4 5. The sensitivity of the radar module will be set automatically by the GPC after power up the gate system. To check/set the sensitivity see also 7.2.2 Configuration and Test in ISO-Host or Buffered Read Mode, Step 8 1.Radarmodule ID ISC.ANT.GPC-E2 X11 X12 ID ISC.ANT1520680-GPC Fig.
IDENTIFICATION 7 Installation ID ISC.ANT1520/700-HPDA/-HPDB Installation Gate People Counter ID ISC.ANT.GPC in antenna Type HPDB 7.1 Installation and Connections 3. 6. 7. 1. 2. 5. 12. 8. 8. 12. 8. 9. 4. Contents of the 1. 1 piece connection cable People Counter –Terminal board 2. 1 piece Radar connection cable 3. 1 piece LED connection cable 4. 1 piece People Counter Board 5. 1 piece Radar module 6. 1 piece cable tie 7. 4 piece screw for plastic 3x12mm 8.
IDENTIFICATION Step Installation Action ID ISC.ANT1520/700-HPDA/-HPDB Note Disconnect LED connection cable at the terminal board and cut the cable tie in the antenna foot. 1. 2. Disconnect LED connection cable at LED controller. FEIG ELECTRONIC GmbH Page 63 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 3. Remove the cable clip beside the LED controller. 4. Remove the 2 other cable clips by pulling them out with the cable. FEIG ELECTRONIC GmbH Installation Page 64 von 92 ID ISC.ANT1520/700-HPDA/-HPDB ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 5. Install People Counter Board into antenna with screws for plastic 6. Plug GPC connection cable onto X1 at GPC and X5 GPC-in at terminal board and fix it with two cable clips and the cable tie. FEIG ELECTRONIC GmbH Installation Page 65 von 92 ID ISC.ANT1520/700-HPDA/-HPDB ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 7. Attention !! Note: Do not touch the antenna surface of the Radar module to avoid damaging the electronic components and soiling. 8. Connect radar connection cable with X1 of Radar module. 9. Plug Radar connection cable onto X11 Sen 1 at GPC and fix the cable with the cable clip. 10. Install Radar module with split rivet. Use installation hole that radar module surface faces between the antennas. 11. The sensitivity of the radar FEIG ELECTRONIC GmbH Installation ID ISC.
IDENTIFICATION 12. module will be set automatically by the GPC after power up the gate system Connect LED cable with X1 of LED controller and fix it with the cable clips. Connect the LED cable with X3 of GPC 13. Close antenna with antenna cover with display window After the installation you have to stick the adhesive label of the GPC below the type plate of the antenna. 14. The detection of the 2.and 3.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 7.2 Configuration and Test To activate the People Counters the following settings has to be done. Set additional the Jumpers JP10 and J11 of Reader ID ISC.LRM2500-B to configure the RS485 interface. (see also manual M01111-xde-ID-B , page 54 and 55). The Termination has to be activated via software in the reader configuration. VCC 500 Ω J11 RS485 + RS485 J10 500 Ω Fig. 28: Jumper settings RS485 Interface 7.2.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 7.2.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB „True“ means: LED with Bus Address 11, 12, 13, 14 will be active if the reader read a valid transponder on the corresponding antenna 7 8 Set by clicking on „Apply“. The sensitivity of the connected radar modules could be set in -Peripheral Device Commands -People Counter -at Busaddress 1,2 and 3 -Byte 11: 00 = Low 05 = Middle 0A = High 0F = Very high (Default) 1. 2. First “Read” out actual setting of sensitivity.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Select Command „Set People Counter Values“ 12 13 Confirm with „Send“ Select Command „Get People Counter Values“ 13 Confirm with „Send“ 14 All counter values should be 0 Walk through the gate from both directions. 15 Counter 1 | Counter 2 In | Out Select Command „Get People Counter Values“ 16 17 Confirm with „Send“ FEIG ELECTRONIC GmbH Page 71 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB Counter values will be displayed. 18 In ISO-Host and Buffered Read the People Counter has to be polled by the Host Application to get the data. FEIG ELECTRONIC GmbH Page 72 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB In Notification Mode the Reader sends the People Counter Data automatically to the Host. 7.2.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB A Test could be done with the People Counter Sample. 8 Therefore you will have to set both ports have the same address, at the TCPSettings. 9 FEIG ELECTRONIC GmbH Page 74 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 7.2.4 Using the trigger function of the Gate People Counter The trigger function could only be used in one of the Automatic Modes. The trigger function works bidirectional, but a 100% safe reading of transponder is only possible form one direction. Due to this, it is necessary at the installation of the antennas, that the Radar module / Antenna faces to the direction of the transponder which could cause the alarm. At buildings (e.g.
IDENTIFICATION Step Installation Action ID ISC.ANT1520/700-HPDA/-HPDB Note Select „Configuration“ 1 Operating Mode 2 3 Select -Buffered Read Mode or -Notification Mode Confirm with „Apply“ Operating Mode 4 5 6 Set -Trigger enable -Source Input No 2-Trigger TriggerUse set to - Start Trigger - Hold Time e.g. 20x100ms =2sec. Confirm with „Apply“ Multiplexer stops switching of antennas. All Output LED´s at Outputs of Multiplexer are switched off. Walk through the gate.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 7.2.5 Using the direction detection of transponder with the People Counter In combination with the People Counter a direction detection of the transponders could be performed in that way, that only transponder will cause an alarm which move in the configured direction through the gate. This should reduce false alarms.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 7.2.6 Detection Area of Direction Mode Tested with: Gate width: 150cm 20cm Radar sensitivity : Very High Transponder: 60cm I-Code SLiX (45x75mm) Walking directions 20cm 20cm 60cm Walking directions Walking directions Fig. 31 FEIG ELECTRONIC GmbH Page 78 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION 8 Installation ID ISC.ANT1520/700-HPDA/-HPDB Configure the reader in accordance with national RF regulations Configuration of the RFID readers and the maximum transmitting power of the antennas are affected mainly by the country-specific RF regulations. For the entire EU the limits are set forth in the R&TTE Directive and EN 300 330. The ID ISC.ANT1520/680 antenna with the ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB The reader needs to be configured as follows depending on the installation location: Parameter USA / Canada / Europe Air Interface RF-Power: maximum 4 W RF Modulation: 15% Transponder RF Modulation / ISO-MODE / MOD RF Data coding ISO-MODE: Timeslots ISO-MODE / NO-TS ISO Option – BREAK: FEIG ELECTRONIC GmbH 10% Fast (1/4) or Normal (1/256) 1 or 16 Timeslots Complete Timeslot length at „NO TAG“ Page 80 von 92 ID ISC.
IDENTIFICATION 9 Installation ID ISC.ANT1520/700-HPDA/-HPDB Technical Data 9.1 Antenna ID ISC.ANT1520/700 Type HPDA and HPDB Mechanical Data • Housing UV stabilized ABS and Acrylic • Dimensions ( W x H x D ) 680 mm x 1798 mm x 76 mm ± 3 mm 850 mm x 1920 mm x 162 mm ± 10 mm – Antenna – Packing • Weight – ID ISC.ANT1800/700-HPDA – ID ISC.ANT1800/700-HPDB Approx. 29 kg without /33,5 kg with packing Approx.
IDENTIFICATION Installation • ID ISC.ANT1520/700-HPDA/-HPDB Operating (No alarm) 17 VA Operating (Alarm LED+Buzzer switched on) Single Gate 31,5 VA Double Gate 38,5 VA Triple gate 48,5VA • Operating Frequency 13,56 MHz • Maximum transmitting power per 4W antenna • Permissible overall transmitting power per antenna gate – EU-territory (per EN 300 330) – USA (per. FCC Part 15) - Canada (per. RSS210) 4.0 W 4.0 W 4.
IDENTIFICATION Installation ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.2 People Counter ID ISC.ANT.GPC and ID ISC.ANT.GPC-E2 Mechanical Data • Housing Printed Boards • Board Dimensions ( B x H x T ) 100 mm x 40 mm x 16 mm ± 1 mm 60 mm x 30mm x 25 mm ± 1 mm – People Counter Board – Radar Sensor Board • Weight – ID ISC.ANT1800/700-GPC – ID ISC.ANT.GPC-E ca. 200 g / 250 g (0.55 lb) with packing ca. 50 g / 100 g (0.22 lb) with packing Electrical Data • Supply Voltage • 24 V • Power Consumption • max.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.3 Power Supply ID ISC.NET24V-B Will be included in the packaging of the antenna ID ISC.ANT1520/700 Type HPDA Mechanical Data • Type Desktop power supply with IEC socket according IEC60320-C13, 3-pin • Housing Plastic • Dimensions ( W x H x D ) 58 x 30,5 x 132 mm ± 1 mm • Weight Approx.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.4 Approvals As per Section 7 9.4.1 Europe (CE) 9.4.1.1 Antenna ID ISC.ANT1520/700-HPD This RF equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC dated March 99. Equipment Classification according to ETSI EN 300 330 and ETSI EN 301 489: Class 2 The technical data of the ID ISC.LRM2500-B Reader built into the ID ISC.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.4.2 USA (FCC) and Canada (IC) 9.4.2.1 Antenna ID ISC.ANT1520/700-HPD Product name: ID ISC.ANT1520/700-HPD Antenna name: ID ISC.ANT1520/700 Type HPDA Reader name: ID ISC.LRM2500-B FCC ID: IC: Notice for USA and Canada PJMLRM2500 6633A-LRM2500 This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.4.2.2 People Counter ID ISC.ANT1520/680-GPC FCC ID: IC: Notice for USA and Canada UXS-IPS154US 6633A-GPC This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 9.4.3 USA and Canada (UL) The following picture indicates the label position: FEIG ELECTRONIC GmbH Page 89 von 92 ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
IDENTIFICATION Installation ID ISC.ANT1520/700-HPDA/-HPDB 10 Annex A 10.
IDENTIFICATION Installation X13 / Pin 3 TRG X13 / Pin 4 A- RS485 A- X13 / Pin 5 B+ RS485 B+ ID ISC.ANT1520/700-HPDA/-HPDB TRG Trigger People Counter Table 12: Pin-Configuration X1-X13 Terminal Board 10.
IDENTIFICATION FEIG ELECTRONIC GmbH Installation Page 92 von 92 ID ISC.ANT1520/700-HPDA/-HPDB ID ISC.ANT1520700-HPDA-B User Manual_M61113-0e-IDE.
