MANUAL ID CPR74 RFID-Readermodul Modell Artikel-Nr.. ID CPR74-4SCUSB 4607.000.00 ID CPR74-CUSB 4606.000.00 priliminary – public (B) 2016-09-26 – CPR74-Manual M60610-0e.
OBID® classic-pro Installation ID CPR74 Note Copyright 2016 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited.
OBID® classic-pro Installation ID CPR74 Content 1. Safety Instructions / Warning - Read before start-up ! 4 2. Characterization ID CPR74 5 2.1. Scope of delivery..................................................................................................................6 2.2. Available Accessories .........................................................................................................6 2.3. Available Software Tools, USB Driver and Firmware .......................................
OBID® classic-pro Installation ID CPR74 1. Safety Instructions / Warning - Read before start-up ! The device may only be used for the intended purpose designed by for the manufacturer. The operation manual should be conveniently kept available at all times for each user. Unauthorised changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries.
OBID® classic-pro Installation ID CPR74 2. Characterization ID CPR74 The reader modules ID CPR74 are designed for data exchange (read and write) with passive transponder according ISO14443 type A and type B, ISO15693, ISO18000-3M3 and are capable for communication with NFC devices (ISO18092). The small dimensions and the different available interfaces (RS232-TTL or USB) make it suitable for an easy integration into terminals, housings and other devices.
OBID® classic-pro Installation ID CPR74 2.1. Scope of delivery The delivery contains the following parts: 1 x RFID-Reader module ID CPR74 2.2. Available Accessories Tab. 1 Available Accessories and spare parts Part Number 3674.000.00 Part name Description ID ISC.ANT40/30-U.FL-A 50 Ohm Antennae with U.FL-connector for the connection on the ID CPR74 Dimensions: 40 mm x 30 mm 3673.000.00 ID ISC.ANT100/100-U.FL-A 50 Ohm Antennae with U.
OBID® classic-pro Installation ID CPR74 3. Dimensions The ID CPR74 reader module has been designed for the integration into terminals, printers or handheld devices and so on. Figure 1: Dimension (Top View) Figure 2: Dimension (Side View) FEIG ELECTRONIC GmbH Page 7 of 20 CPR74-Manual M606100e.
OBID® classic-pro Installation ID CPR74 4. Installation and wiring 4.1. Connector X1, X2 The reader can be connected to a RS232-TTL interface and the power supply by using the multipin connector X1. The multi-pin connector X2 provide the connection for the USB interface. The device with SAM Sockets is a self-powered USB device which requires a separate power supply. The following figure 4 and the table shows the assignment of the pins X1 (7pol.) and X2 (5pol.) Typ “JST PH” RM 2 mm (horizontal).
OBID® classic-pro Installation ID CPR74 NOTICE: Only one host interface can be used at the same time. Using several host interfaces at the same time can force malfunctions. The reader has to supplied by a limited power supply (e.g. NEC Class 2/LPS power supply) according IEC EN 60950-1 chapter 2.5, only Use only regulated power supply’s. The connection cable (RS232TTL, USB, VCC) should be as short as possible and must be shorter than 3 m to reduce the influence of noise.
OBID® classic-pro Installation ID CPR74 4.3. Connection of an external Antenna The ID CPR74 modules are equipped with an internal 50 -antenna and have an additionally connector for an external 50 -antenna. In Scan mode it is possible to switch between the two antennas automatically. In the ISOHost Mode the switching of the antenna can be performed by commands. The use of the external antenna is configurable in the reader settings. The connection of the external antenna is possible via the U.
OBID® classic-pro Installation ID CPR74 4.4. SAM Slots Figure 7 shows the position of the 4 SAM slots (S1-4). Each SAM slot is designed for a ID000 formatted SAM Card. NOTICE Wrong inserted SAM cards and forcefully opening or closing can damage the SAM slot. See chapter: 4.4.1. Installation of a SAM Card in a SAM Figure 7: Position of the 4 SAM Sockets FEIG ELECTRONIC GmbH Page 11 of 20 CPR74-Manual M606100e.
OBID® classic-pro Installation ID CPR74 4.4.1. Installation of a SAM Card in a SAM Socket The following step by step instruction shows the installation of a SAM Card into the SAM socket S1. 1. Closed SAM socket without SAM card. 2. Push the latch to the right side and open the cover carefully. 3. Put the SAM card into the cover. The contact 4. The SAM card must be pushed up against plate face up and the beveled corner outside the stop angle. 5.
OBID® classic-pro Installation ID CPR74 5. Power supply The reader ID CPR74-SCUSB with 4 SAM slots is designed as a “Self-Powered USB Device” and needs an additional 5 V DC power supply. The power supply must meet the following specification: +5 V DC ± 5 % Ripple: 0...250 kHz < 10 mVpp from 250 kHz < 0,1 mVpp Note: On both device variants you need to take care that the voltage supply of the USB port is not connected in the case if an external power supply is connected. 5.1.
OBID® classic-pro Installation ID CPR74 6. Indicators / LEDs The reader modules has two LED indicators on board (green and red) After power on or after a CPU Reset both LED’s starts blinking synchronously for about 2s. While operation the LED’s signalizes the following operating status: LED - green flashes: Reader is ready for operation but has no host communication shine: Polling-Mode: Reader is ready for work and has communication with the host. Scan-Mode: Reader is working in Scan-Mode.
OBID® classic-pro Installation ID CPR74 7. Installation notes Be aware of the following possible environmental factors when installing an ID CPR74 into another device : Effects from nearby metal objects Detuning of the integrated antenna Impaired communication of the antenna’s magnetic field EMC effects on cables Impaired communication between reader and transponder EMC effects from magnetic fields Impaired communication between reader and transponder 7.1.
OBID® classic-pro Installation ID CPR74 7.3. EMC effects from magnetic fields The communication principle of RFID- Technology is based on the modulation of electromagnetic fields. Alternating magnetic fields in the vicinity of the antenna can have a negative influence on the reader function. Sources of such magnetic interference fields include coils within a primary or secondary switching power supply.
OBID® classic-pro Installation ID CPR74 8. Technical Data Tab. 3: Technical data ID CPR74 Weight approx. 20 g Operating -25 °C up to +70 °C (-13 °F up to +158 °F) Storage -40 °C up to +85 °C (-40 °F up to +185 °F) Temperature Range Humidity max. 95 % (not condensing) MTBF 500 000 h +5 V DC ± 5 % Ripple: 0...
OBID® classic-pro Installation ID CPR74 Europe Radio Approval EN 300 330 FCC 47 CFR Part 15 USA IC RSS-210 Canada EMV EN 301 489 EN 62368 Safety and Health EN 50364 WEEE - 2002/96/EC Waste and Hazardous Substances RoHS - 2011/65/EC Tested according EMVCo Contact Level 1 Miscellaneous Certification suitability according EMVCo Contactless Level 1, VDV-KA,ITSO and in the future CEN/TS 16794 (see chapter: 2. Characterization ID CPR74) FEIG ELECTRONIC GmbH Page 18 of 20 CPR74-Manual M606100e.
OBID® classic-pro Installation ID CPR74 9. Approvals 9.1. Europa (CE) Hereby, FEIG ELECTRONIC GmbH declares that the radio equipment type ID CPR74 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.feig.de/en/downloads-support/declarations-of-conformity.html Performance Classification according to ETSI EN 301 489: Class 2 FEIG ELECTRONIC GmbH Page 19 of 20 CPR74-Manual M606100e.
OBID® classic-pro Installation ID CPR74 9.2. USA (FCC) and Canada (IC) Product name: ID CPR74 FCC ID: PJMCPR74 IC: Notice for USA and Canada 6633A-CPR74 This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
