INSTALLATION ID CPR60 RFID Reader Module Modell Artikel Nr. ID CPR60-A 5491.000.00 draft – public (B) 2020-04-27 – CPR60_Installation M91210-0e_03.
IDENTIFICATION Installation ID CPR60 Note Copyright by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited.
IDENTIFICATION Installation ID CPR60 Content 1. Safety Instructions / Warning - Read before start-up ! 4 2. Characterization ID CPR60 5 2.1. Available Accessories ....................................................................................................... 5 2.2. Available Software Tools, USB Driver and Firmware ...................................................... 6 3. Dimensions 7 4. Installation and wiring 8 4.1. Connector X1 ........................................................
IDENTIFICATION Installation ID CPR60 1. Safety Instructions / Warning - Read before start-up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorised changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries.
IDENTIFICATION Installation ID CPR60 2. Characterization ID CPR60 The ID CPR60 is a RFID reader which supports ISO/IEC 14443 A/B and ISO 15693 contactless smart cards and transponders. It also offers 4 interfaces to connect ISO 7816 smart cards with contacts. Three different antennas, can be connected can be connected to the 50 Ohm antenna output. The antennas have different dimensions: Antenna No. 1 ID ISC.ANT100/100 with 100x100mm, Antenna No. 2 ID ISC.ANT40/30 and Antenna No.
IDENTIFICATION Installation ID CPR60 2.2. Available Software Tools, USB Driver and Firmware The USB driver and the test and configuration tool “CPRStart” are available on our FEIG download area: https://www.feig.de/en/login/ Username: feig_ Customer Password : For firmware updates we are providing the “FirmwareUpdateTool” and a external firmware xml-file. 2.3. Development Board For demonstration and development purposes a special PCB with connectors, SAM sockets and power supply is available on request.
IDENTIFICATION Installation ID CPR60 3. Dimensions The ID CPR60 reader module has been designed for the integration into terminals, printers or handheld devices and so on. Figure 1: Dimension (Top View) Figure 2: Dimension (Side View) FEIG ELECTRONIC GmbH Page 7 of 16 CPR60_Installation M91210-0e_03.
IDENTIFICATION Installation ID CPR60 4. Installation and wiring 4.1. Connector X1 X1 (Connector Type: Hirose DF17(2.5)-80DP-0.5V(57)) is the main connector for power supply, interfaces and control signals. The following table shows the pin-assignment of the connector. Interfaces and functions are described from the ID CPR60 view (an input must be connected to one output or vice versa). X1 Figure 3: Connector X1 At connector X1 four external smart card connectors can be connected.
IDENTIFICATION PIN Function 31 Installation Remark ID CPR60 PIN Function n.c. 32 GND 33 n.c. 34 KCC_VCC (SAM 4) 35 GND 36 SAM1_CLK 37 SPI_MISO* CPR60 is Slave 38 SAM2_CLK 39 SPI_MOSI* CPR60 is Slave 40 USB DP* 41 SPI_nCS** CPR60 Input 42 USB DM* 43 SPI_CLK** CPR60 Input 44 n.c. 45 n.c. 46 n.c. 47 SAM1_ RST 48 n.c.
IDENTIFICATION Installation ID CPR60 4.2. Connector ANT The ID CPR60 module is equipped with an connector for an external 50 Ω-antenna. The connection of the external antenna is possible via the U.FL connector „ANT“. ANT: (U.FL) Figure 4: Connection of an external antenna NOTICE: 1. Three different antennas can be connected. The antennas have different dimensions. Antenne 1 (100 x 100mm) ID ISC.ANT100/100 Antenne 2 (40 x 30mm) ID ISC.ANT40/30 Antenne 3 (30 x 30mm) RFID Antenna Board 445-100302 2.
IDENTIFICATION Installation ID CPR60 5. Standby / Low Power Card Detection The ID CPR60 offers a standby mode to reduce the power consumption to a minimum. The standby mode can be controlled by the host via input nLOW_PWR (see: 4.1. Connector X1). The standby mode is activated if input nLOW_PWR is set to low. In this mode the reader wakes up if: - a contactless card is detected in front of the RFID antenna or - if the Input nKCC_DET is set to 0 The reader remains active for a configurable time.
IDENTIFICATION Installation ID CPR60 6. Technical Data Tab. 2: Technical data ID CPR60 Dimension (W x H x D) max. 41 mm x 41 mm x 6,5 mm Weight approx. 10 g Operating -25 °C up to +70 °C (-13 °F up to +158 °F) Storage -40 °C up to +85 °C (-40 °F up to +185 °F) Temperature Range Humidity max. 95 % (not condensing) 1 Power Supply Current Consumption Interfaces • for digital circuit: 3,3 V DC ± 5 % max power consumption: 100 mA • for analog circuit: 5 V DC ± 5 % Ripple: 0...
IDENTIFICATION Installation Europe Radio Approval ID CPR60 EN 300 330 USA Available on request Canada Available on request EMV EN 301 489 EN 60950 Safety and Health EN 50364 WEEE - 2002/96/EC Waste and Hazardous Substances RoHS - 2011/65/EC FEIG ELECTRONIC GmbH Page 13 of 16 CPR60_Installation M91210-0e_03.
IDENTIFICATION Installation ID CPR60 7. Approvals 7.1. Europa (CE) Hereby, FEIG ELECTRONIC GmbH declares that the radio equipment type ID CPR60 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.feig.de/en/downloads-support/declarations-of-conformity.html Performance Classification according to ETSI EN 301 489: Class 2 FEIG ELECTRONIC GmbH Page 14 of 16 CPR60_Installation M91210-0e_03.
IDENTIFICATION Installation ID CPR60 7.2. USA (FCC) and Canada (IC) Product name: ID CPR60 FCC ID: PJMCPR60 6633A-CPR60 IC: Notice for USA and Canada This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IDENTIFICATION Installation ID CPR60 The manufacturer is obliged to test the terminal device together with the reader module according to the national FCC requirements according to 47 CFR Part15 §209 and §225 For this purpose the reader module must be set to normal operation, ScanMode.
