MONTAGE INSTALLATION ® OBID classic pro ID CPR.02-A (RS232 Interface) ID CPR.02-B (RS485 Interface) (deutsch / english) preliminary public (B) 2002-09-13 M10701-1de-ID-B.
® DEUTSCH Montage deutsche Version ab Seite 3 ENGLISH OBID classic pro english version from page 20 Seite 2 von 36 ID CPR.
® Montage OBID classic pro ID CPR.02-x Hinweis Copyright 1999 - 2002 by FEIG ELECTRONIC GmbH Lange Straße 4 D-35781 Weilburg-Waldhausen Tel.: +49 6471 3109-0 http://www.feig.de Alle früheren Ausgaben verlieren mit dieser Ausgabe ihre Gültigkeit. Die Angaben in diesem Handbuch können ohne vorherige Ankündigung geändert werden. Weitergabe sowie Vervielfältigung dieses Dokuments, Verwertung und Mitteilung ihres Inhalts sind nicht gestattet, soweit nicht ausdrücklich zugestanden.
® DEUTSCH OBID classic pro Montage ID CPR.02-x Inhalt 1. Sicherheits- und Warnhinweise 5 2. Montage 6 3. 4. 2.1 Montage auf Unterputzdose....................................................................................... 7 2.2 Montage mit Aufputzrahmen ID APR-A..................................................................... 8 Leseranschluss 3.1 Jumper und Schalter ................................................................................................ 10 3.
® OBID classic pro Montage ID CPR.02-x 1. Sicherheits- und Warnhinweise • Das Gerät darf nur für den vom Hersteller vorgesehenen Zweck verwendet werden. • Die Bedienungsanleitung ist zugriffsfähig aufzubewahren und jedem Benutzer auszuhändigen. • Unzulässige Veränderungen und die Verwendung von Ersatzteilen und Zusatzeinrichtungen, die nicht vom Hersteller des Gerätes verkauft oder empfohlen werden, können Brände, elektrische Schläge und Verletzungen verursachen.
® DEUTSCH OBID classic pro Montage ID CPR.02-x 2. Montage Der Leser ist für die Wandmontage auf 60 mm Unterputzdosen vorgesehen. Für die Aufputzmontage kann das Gehäuseunterteil durch den Aufputzrahmen ID APR-A, der als Zubehör lieferbar ist, ersetzt werden. HINWEISE: • Der Leser sollte nicht direkt auf leitende Materialien wie Metallflächen, Metallgitter (Armierung) oder metallisierte Oberflächen montiert werden, da diese Flächen eine Reduzierung der Lesereichweite bewirken.
® OBID classic pro Montage ID CPR.02-x 2.1 Montage auf Unterputzdose 1. Montageort auswählen: Die Montage sollte auf einem möglichst ebenen Untergrund erfolgen. 2. Anschluss: siehe Kapitel Leseranschluss. 3. Inbetriebnahme: • Anschlussplatine in das Gehäuseunterteil einrasten (siehe: Abbildung 2). • Gehäuseoberteil auf Gehäuseunterteil stecken. Dabei die Stiftleiste der Leserelektronik sauber in Buchsenleiste X3 einführen! • siehe Kapitel Inbetriebnahme 4.
® Montage DEUTSCH OBID classic pro ID CPR.02-x 2.2 Montage mit Aufputzrahmen ID APR-A 1. Wandmontage: • Die Montage sollte auf einem möglichst ebenen Untergrund erfolgen. • Durchbrüche für Zuleitung im Gehäuseunterteil herstellen, ggf. Würgenippel einsetzen und Zuleitung einziehen. • Gehäuseunterteil mit Untergrund verschrauben. 2. Anschluss: siehe Kapitel Leseranschluss. 3. Gehäuse schließen: • Anschlussplatine (1) gem.
® Montage OBID classic pro ID CPR.02-x 3. Leseranschluss Der Anschluss des Lesers erfolgt über die Anschlussplatine (siehe: Abbildung 4), die im Gehäuseunterteil eingerastet wird. CLK DAT IN1 IN2 X1 X3 X2 +/~ -/~ CLS COM NO GND R/A T/B Abbildung 4: Anschlussplatine Klemme Leiste X2 X1 Funktion Bezeichnung +/~ -/~ CLS COM NO GND R/A T/B CLK DAT IN1 IN2 FEIG ELECTRONIC GmbH ID CPR.02-A ID CPR.
® Montage DEUTSCH OBID classic pro ID CPR.02-x 3.1 Jumper und Schalter Abbildung 5 zeigt die Lage der Jumper und Schalter auf der Leiterplatte des ID CPR.02-x. Die Jumper und Schalter sind nur bei demontiertem Gerät zugänglich. X7 1 J1 J2 12345678 S1 ON OFF X1 X4 X3 X2 3 2 1 Abbildung 5: Jumper und Schalter S1: DIP-Schalter zur Einstellung der Leseradresse. X1: Stiftleiste zum Aufstecken der Anschlussplatine. X2 / X3 / X4: Jumper für Abschlusswiderstände der RS485-Schnittstelle (nur ID CPR.
® Montage OBID classic pro ID CPR.02-x 3.2 Spannungsversorgung Die Spannungsversorgung erfolgt über die Klemmen [+ / ~] und [- / ~]. Das Gerät kann wahlweise mit 12 - 24 V AC oder DC versorgt werden. Die Polarität bei DC Spannungsversorgung kann frei gewählt werden. HINWEIS: Die Zuleitung sollte nicht direkt parallel mit anderen Energieversorgungs- und Niederspannungsleitungen verlegt werden. 3.3 Relais Der Leser verfügt über ein Relais mit einem Schließerkontakt.
® Montage DEUTSCH OBID classic pro ID CPR.02-x 3.6 RS485-Schnittstelle (ID CPR.02-B) Bei einem RS485-Datenbus kann es notwendig werden Abschlusswiderstände einzusetzen. Die Notwendigkeit zum Einsatz von Abschlusswiderständen ist für jede Installation im Einzelfall zu prüfen, da dies z. B. von Leitungslängen, Busaufbau, Spannungsversorgung der Leser und dem verwendeten Leitrechner abhängig ist. Der Abschlusswiderstand ist i.d.R. nur am Busende, also am letzten Gerät, notwendig.
® Montage OBID classic pro ID CPR.02-x 3.7 Daten-/Taktschnittstelle Der Anschluss der Daten-/Taktschnittstelle erfolgt gem. Abbildung 11. Falls am Host kein CLS Anschluss vorgesehen oder notwendig ist, kann auf diese Leitung verzichtet werden. Host CLOCK DATA CLS GND CLK DAT CLS GND ID CPR.
® Montage DEUTSCH OBID classic pro ID CPR.02-x 4. Inbetriebnahme 4.1 Adresseinstellung (Busbetrieb mit RS485-Schnittstelle) An Lesern mit RS232-Schnittstelle ist i.d.R. keine Adresseinstellung notwendig. Bei Geräten mit RS485-Schnittstelle kann die Geräteadresse entweder über den DIP-Schalter am geöffneten Gerät (siehe Abbildung 5), oder über den Leitrechner (Host) erfolgen.
® Montage OBID classic pro ID CPR.02-x 5. Technische Daten Gehäuse Kunststoff ASA Farbe Gehäuseunterteil: Gehäuseoberteil: ähnlich RAL 9002 (grauweiß) ähnlich RAL 7043 (verkehrgrau) Gewicht ca. 120 g Schutzart IP 54 Spannungsversorgung 12 - 24 V AC/DC Leistungsaufnahme max.
® DEUTSCH OBID classic pro Montage ID CPR.02-x 5.1 Zulassung Die Funkanlage entspricht, bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des Artikels 3 und den übrigen einschlägigen Bestimmungen der R&TTE Richtlinie 1999/5/E6 vom März 99.
® Montage OBID classic pro ID CPR.02-x 5.
® DEUTSCH OBID classic pro Montage ID CPR.02-x 5.
® Montage OBID classic pro ID CPR.02-x 6. Lieferumfang: 1 x Gehäuseunterteil (Unterputzgehäuse) 1 x Gehäuseoberteil mit Leserelektronik 1 x Anschlussplatine 1 x Frontaufkleber 1 x Schneidschraube 3,2 x 25 mm (zur Verbindung der Gehäuseteile) 2 x Schneidschrauben 3,2 x 15 mm (zur Wandmontage) 1 x Montageanleitung 6.1 Optionales Zubehör Gehäuseunterteil für Aufputzmontage ID APR-A Bestell-Nr.: 1144.001.00 Frontaufkleber ID AKL.02 Frontaufkleber Bestell-Nr.: 1424.000.
® OBID classic pro Installation ID CPR.02-x Note Copyright 1999 - 2002 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg-Waldhausen Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority.
® OBID classic pro Installation ID CPR.02-x Content 1. Safety instructions – please read carefully prior to initiation 22 2. Installation 23 3. 4. 2.1 Installation on flush-mounting box ......................................................................... 24 2.2 Installation with surface frame ID APR-A................................................................ 25 Reader-connection 3.1 Jumper and Switches...............................................................................
® OBID classic pro Installation ID CPR.02-x 1. Safety instructions – please read carefully prior to initiation • The device has to be used only for the purpose designed by the manufacturer. • The operation manual has to be stored available at any time and has to be handed over to each user. • Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries.
® OBID classic pro Installation ID CPR.02-x 2. Installation The Reader has been designed for wall installation on 60 mm flush-mounting box. For surface installation, the bottom part of the casing can be substituted by the surface frame ID APR-A, which is available as an attachment. NOTES: • The Reader must not be installed directly upon conductive materials as e.g. metal sur- faces, metal grids (reinforcements) or metallized surfaces, as these surfaces reduce the detection range of the Reader.
® Installation OBID classic pro ID CPR.02-x 2.1 Installation on flush-mounting box 1. Select installation place: The installation should be executed always on a surface as even as possible. 2. Connection: see chapter Reader-connection 3. Operation: • snap connection board into bottom part of casing (see Fig 2). • Put the top of the casing onto its bottom part. The pin board of the Reader electronic has to be inserted carefully into the socket board X3! • see chapter Installation 4.
® Installation OBID classic pro ID CPR.02-x 2.2 Installation with surface frame ID APR-A 1. Wall installation: • The installation should be executed always on a surface as even as possible. • Make openings into the bottom part of the casing for lead-in wire, eventually attach twisting sleeve and pull wire into the casing. • Screw bottom part of casing to surface. 2. Connection: see chapter Reader-connection 3.
® Installation OBID classic pro ID CPR.02-x 3. Reader-connection The connection of the Reader is executed via the connection board. (see: Fig 4) which is snapped into the bottom part of the casing. CLK DAT IN1 IN2 X1 X3 X2 +/~ -/~ CLS COM NO GND R/A T/B Fig 4: Connection board connector board name +/~ -/~ X2 X1 CLS COM NO GND function ID CPR.02-A ID CPR.
® Installation OBID classic pro ID CPR.02-x 3.1 Jumper and Switches Fig 5 shows the position of the jumpers and switches on the printed circuit board of the ID CPR.02-x. The jumpers and switches are only accessible at the opened device. X7 1 J1 J2 12345678 ON OFF S1 X1 X4 X3 X2 3 2 1 Fig 5: Jumper and Switches S1: DIP-switch to configure the Reader address. X1: Terminal for sticking up the connection board. X2 / X3 / X4: Jumper for termination resistors of the RS485 interface (only ID CPR.02-B).
® Installation OBID classic pro ID CPR.02-x 3.2 Power supply The power supply is effected via the connectors [+ / ~] and [- / ~]. The device may be supplied either with 12 - 24 V AC or DC. In case of DC supply, the polarity may be chosen freely. NOTE: The lead-in wire should not be laid directly parallel to other power supply- and low voltage wires. 3.3 Relay The device is equipped with an relay (normally open contact). The connection is executed via the connectors [NO] and [COM]. 3.
® Installation OBID classic pro ID CPR.02-x 3.6 RS485 Interface (ID CPR.02-B) With RS485 data buses, it can be necessary to use terminating resistors. For each installation, checks should be made as to whether it is necessary to use terminating resistors, because this e.g. is dependent on line lengths, bus structure, powering of the Readers and the employed host computer. Generally, a terminating resistor is only required at the end of the bus, i.e. on the last unit.
® Installation OBID classic pro ID CPR.02-x 3.7 Data-/Clock interface The connection of the data-/clock interface is executed according to Fig 11. If no CLS signal is required on host, this connection can be abandon. Host CLOCK DATA CLS GND CLK DAT CLS GND ID CPR.
® Installation OBID classic pro ID CPR.02-x 4. Operation 4.1 Address setting (Bus mode with RS485 interface) For Readers with RS232 interfaces usually no address setting is necessary. In case of units with RS485 interface, the unit address can be set either via the DIP-switch on the opened unit (see Fig 5), or via the host.
® Installation OBID classic pro ID CPR.02-x 5. Technical data casing Plastic material ASA colour bottom part of casing: similar to RAL 9002 (greyish white) top of casing: similar to RAL 7043 (traffic grey) weight approx. 120 g protective system IP 54 power supply 12 - 24 V AC/DC power consumption max.
® OBID classic pro Installation ID CPR.02-x 5.1 Approval When properly used this radio equipment conforms to the basic requirements of Article 3 and the other relevant provisions of the R&TTE Directive 1999/5/E6 of March 99.
® OBID classic pro Installation ID CPR.02-x 5.
® OBID classic pro Installation ID CPR.02-x 5.
® Installation OBID classic pro ID CPR.02-x 6. System delivery contents: 1 x bottom part of casing (concealed casing) 1 x top of casing with Reader electronic 1 x connection board 1 x adhesive label 1 x thread cutting screw 3,2 x 25 mm (for connecting parts of casing) 2 x thread cutting screws 3,2 x 15 mm (for wall installation) 1 x Installation instructions 6.1 Optional Accessories bottom part of casing for surface installation ID APR-A Order-No.: 1144.001.00 adhesive front label ID AKL.