FOBOOST Fiber Optical Cell Signal Booster Installation Guide NEED HELP ? fddiboost@163.
CATALOG Package Contents 1 Preparation 2 STEP 1: Master Unit and Remote Unit Placement 3 STEP 2: Mount Outside Antenna 4 STEP 3 : Route & Connect Outside Antenna To Master Unit 7 STEP 3 : Route & Connect Inside Antenna To Remote Unit 8 STEP 4: Connect Master Unit To Remote Unit 10 STEP 5: Power Up The Booster & Optimize The System 12 Measuring Booster Performance 13 Safety Guidelines 15 Specifications Warranty 16 17
Package Contents Master Unit (MU) Remote Unit (RU) Outside Omni Antenna Inside Panel Antenna 100ft Fiber Optic Cable 10ft Fiber Optic Jumper (×2) 30ft LMR240 cable (×2) Power Supply (×2) Wall Mount Bracket Pole Mount Bracket Protection box (×2) Lighting Surge Protector 1
Preparation You Will Need (tools not included) Make sure the following materials are prepared and ready for your installation. 1 to 2 hours 2 people p p p p Ladder Drill (if routing cable through wall) 1”-3” diameter existing pole for mounting Outdoor Antenna (Pole Mount can be purchased separately if needed) Recommended: Power Strip with surge protection NOTE: Please find the most optimal location for the Inside and Outside Antenna before permanently fixing it.
Step 1: Master Unit and Remote Unit Placement Place the Master Unit and Remote Unit in your desired location. NOTE: Do not connect booster to power until the system is fully installed. Choose right position for the Master Unit and Remote Unit • 1 feet away from any other metallic objects • 3 feet away from any windows • The distance between the Master Unit and the Remote Unit should be bigger than 100 feet. Because the length of fiber optic cable is 100ft.
Step 2: Mount Outside Antenna Pole mounting and wall mounting are included. Attach the Mount to the Outside Antenna and use the Bracket Clamps to attach the Antenna to a pole or exhaust pipe. ① ② ③ Make sure that the outside unit is mounted at least 3 feet away from any windows. Outdoor antenna must be installed over the roof line. NOTE: Mounting on existing roof exhaust pipe would be a good time-saver option. Watch out for power lines.
Install the outside antenna in the corner of the building and face it towards nearest cell phone tower. To find the nearest tower, use an app such as 'Open Signal'. This is the most critical step of the installation process because it will determine the overall performance of the booster system.
Keep enough distance between outside and inside antenna NOTE: The Outside Antenna must be at least 60 feet ( 18 meters) horizontal distance or 30 feet ( 9 meters) vertical distance from the Inside Antenna for best performance. The greater the separation between the Inside and Outside Antennas, the better performance you will get from the booster.
Step 3: Route & Connect Outside Antenna To Master Unit Connect the 30ft LMR240 cable to Outside Antenna and route cable into the home, secure the cable near the antenna. All connections should be finger tightened only. Route cable to the MU and connect to the port labeled 'OUTSIDE'.
Step 3: Route & Connect Inside Antenna To Remote Unit Connect the 30ft LMR240 cable to Inside Panel Antenna, and connect the other end of the cable to the 'INSIDE' port on the RU.
(STEP 3-A cont.) Wall Mounting Option Fasten bracket to back of Inside Antenna Secure bracket to wall Tap anchors in Drill holes Note: Choosing a location facing all over your home will help to maximize your coverage area.
Step 4: Connect Master Unit To Remote Unit Connect two 10ft Fiber Optic Jumpers to the ports labeled "FIBER OPTIC" on the MU and RU respectively. Insert the SC connector of the fiber optic jumper connecting the MU into the protective box. Snap the connector into one end of the protection box's SC-to-SC coupler. Insert the100ft fiber optic cable's SC connector into the opposite end of the protection box. Snap the connector into the other end of the SC-to-SC coupler.
Close the protection box, making sure both fiber-optic cables are threaded snuggly in the gaskets at the exit points. Repeat steps with the the fiber optic jumper connecting the RU.
Step 5: Power Up The Booster & Optimize The System Plug into the power supplys on MU and RU respectively, and connect them to the nearest power outlet. NOTE: We strongly recommend using a power strip with surge protection.
Measuring Booster Performance How To Get Signal Strength As A Number iPhone® Dial *3001#12345#* then press Call. 1 Hold down power button until you see 'Slide to Power Off'. 2 Then release the power button. 3 Hold the Home button until your main screen appears. If you want to check 3G/1x but your iPhone is picking up 4G/ LTE signal, go to Settings>Cellular>Cellular Data Options>En_x0002_able .LTE>Select Off.
How To Confirm That Your Installation Is Correct And Effective? Having an accurate measurement of signal strength in decibels (dBm) is crucial when installing your system. Decibels accurately measure the signal strength you are receiving. (MEASURING BOOSTER PERFORMANCE cont.
Safety Guidelines To uphold compliance with network protection standards, all active cellular devices must maintain at least six feet of separation distance from inside unit antenna and outside unit antenna and at least four feet of separation distance from inside unit. Use only the power supply provided in this package. Use of a non-FOBOOST product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 100 degrees Fahrenheit).
Specifications Model Number Fiber-Optical Booster FCC Connectors F-Female on the inside Antenna / F-Female on the Outside Antenna Noise figure 5 dB nominal Antenna lmpedance 75 Ohms / 75 Ohms Weight Frequency(Uplink) Frequency Band Gain(Max) 2.
(EN) This device complies with Industry Canada license-exempt RSS standard(s). promettre le fonctionnement. 3 YEAR WARRANTY The Booster is covered under a three-year product warranty for failures or defects that result from craftsmanship and/or materials. Dated proof of purchase should be retained for use in warranty cases. Contact the retailer/reseller directly with any warranty issues, or alternatively contact the manufacturer in cases where the reseller is no longer available to handle warranty claims.
Notes FOBOOST fddiboost@163.com 3-year manufacturer‘s warranty NEED HELP ? 18 fddiboost@163.