User's Guide

wearfauna.com
Quick User Guide
Welcome to Fauna, your audio glasses! Download the “Fauna“ app now.
Fauna overview
CONNECTION
CHA RGIN G
CONTACTS
CHA RGIN G
CONTACTS
CASE STATUS
GL ASS ES STATUS
TOUCH CONTROL
LEF T TEMPLE
WOOFER
USOUND MEMS
SPE AKER
TOUCH CONTROL
RIGHT TEMPLE
2 M ICROPHO NES
USOUND MEMS
SPE AKER
CHA RGING
CONTACTS
WOOFER
First steps
Using Fauna
L E F T
T E M P L E
R I G H T
T E M P L E
Tap & hold (4 sec.)
Force pairing
Slide back
Volume up
Slide forward
Volume down
Tap & hold (4 sec.)
Decline call
Skip to next song
Double tap
Active voice
assistant
Double tap
Accept call
End call
Play music
Pause music
Important information
Pairing with a device can be forced:
tap and hold for 4 seconds on the right
temple, then connect the host device to
Fauna via Bluetooth. Please note that force
pairing can not be used once Fauna is in
deep-sleep mode.
Fauna is only drip-proof. Please do not
keep it under running water.
Adjustments of frame, length of the temple
and lenses can be made by an optician.
Please leave this to a professional.
Fauna can only be recharged in the case.
Please do not charge any o
ther way.
Charging the glasses
The “glasses status“ LED in the Fauna
case indicates the status of the glasses.
This LED flashes yellow (low charge
level) or green (charge level above 30 %)
if the contacts are connected properly.
At 100 % charge, the LED glows green
for 10 seconds after opening the case.
Charging the case
The 4 LEDs on the outside show the
battery status of the Fauna case. When
the case is charged via USB-C cable,
they will flash. If they glow con
tinuously,
the Fauna case is completely charged.
More about your Fauna
Video user guide and detailed
manuals can be found under:
www.wearfauna.com/support
LED
glasses status
less than 100 %:
flashes green
less than 25 %
100 % charged
less than 75 %
less than 50 %
LED
case status
less than 30 %:
flashes yellow
100 % charged:
lights up green 10 sec.
Instructions for opticians
adjustment. Fauna is suitable for prescription lenses.
Attention:
Fauna contains electronics.
Please follow these
instructions to avoid
any damage.
Activate
Prior
the charging contacts and place the glasses
back in the case to be fully charged. To activate
Fauna, place it in the case and make sure the
LED “glasses status” is lit up. Close the case
and reopen it. Fauna has now been activated
and you will hear: “Hi! Fauna is on”. If Fauna is
not connected to a host device for more than
30 minutes, Fauna will automatically enter
deep-sleep. To wake Fauna up, place it into the
charging case, and after closing and opening the
case Fauna is ready to connect again.
Connect
Place the glasses in the case and close the lid.
Open the lid again, press Fauna against the
charging contacts of the case, make sure the
LED “glasses status” is on, you will hear the
message “Fauna is on, Fauna is pairing”, then
activate Bluetooth on your mobile device and
search for Fauna. The connection is confirmed
with “Great, Fauna is connected.” If you hear
“Please try pairing again,” repeat the proce-
dure. Fauna connects automatically with the
last host device.
Charge
If the
battery charge is below 30 %,
Fauna warns you: “Battery low”. To
charge your Fauna, put it in the
case making sure that the pins are
connected. Close the lid to start the
charging process. To indicate your
Fauna is connected correctly, after
closing the case, the left-most and
right-most of the 4 “case status” LEDs
will light up for 5 seconds. The Fauna
case serves as charging station.
When the Fauna battery level reaches 10%
heard and Fauna goes into deep-sleep.
Levia Black, Fabula Crystal Brown,
Memor Havana, Spiro Transparent Brown.