User Manual X7A Software Version: 1.0.
1 Picture Picture 1 - Desktop phone installation ............................................................................................... 5 Picture 2 - Connecting to the Device .................................................................................................. 6 Picture 3 - Instruction of Keypad ......................................................................................................14 Picture 4 - X7A default home screen ....................................................
Picture 37 – Enable the call forwarding and configure the call forwarding number ........................ 47 Picture 38 - Set call forward .............................................................................................................48 Picture 39 - Transfer interface ..........................................................................................................49 Picture 40 - Semi-Attended transfer ....................................................................................
Picture 75 - Set Private Hold Function Key ....................................................................................... 78 Picture 76 - SMS icon ........................................................................................................................80 Picture 77 - New Voice Message Notification ..................................................................................81 Picture 78 - Voice message interface..................................................................
Picture 113 - Firmware upgrade information display.....................................................................112 Picture 114 - Firmware upgrade .....................................................................................................113 Picture 115 - Reset to default .........................................................................................................114 Picture 116 - Service Port Settings ......................................................................
2 Table Table 1 - Hardware Interface Description ........................................................................................... 6 Table 2 - Keypad Icons ........................................................................................................................ 7 Table 3 - Status Prompt and Notification Icons .................................................................................. 7 Table 4 - DSSkey Icons ....................................................................
3 Safety Instruction Please read the following safety notices before installing or using this unit. They are crucial for the safe and reliable operation of the device. Please use the external power supply that is included in the package. Other power supply may Before using the external power supply in the package, please check the home power voltage. cause damage to the phone and affect the behavior or induce noise. Inaccurate power voltage may cause fire and damage.
4 Overview 4.1 Overview The Fanvil X7A enterprise android network phone is a high-end enterprise color phone with DSS intelligent display screen. With advanced design, high cost performance and paperless office, it can greatly improve the production efficiency of enterprises. The new DSS button design with dynamic intelligent color display screen can replace the traditional function of the extension board.
4.2 Packing Contents 4.2.
5 Install Guide 5.1 Use PoE or external Power Adapter X7A, called as ‘the device’ hereafter, supports two power supply modes, power supply from external power adapter or over Ethernet (PoE) complied switch. PoE power supply saves the space and cost of providing the device additional power outlet. With a PoE switch, the device can be powered through a single Ethernet cable which is also used for data transmission.
5.2 Desktop Installation 5.2.1 X7A Desktop Installation The device supports desktop use. If the phone is placed on the desktop, please follow the instructions in the picture below to install the phone. Picture 1 - Desktop phone installation Please connect power adapter, network, PC, handset, and headphone to the corresponding ports as described in below picture.
Picture 2 - Connecting to the Device Table 1 - Hardware Interface Description Interface Description ① Power Interface Connecting Power Adapter ② Network Interface Connecting to LAN or Internet ③ PC Port Network Interface for Connecting Computer ④ Headset Interface Connecting Headset ⑤ Receiver Interface Connecting Microphone Receiver Index 6
6 Appendix Table 6.
Headphone (HP) Mode Handset (HS) Mode Mute Microphone HD Audio The Voice encryption of calling Open Bluetooth SIP Hotspot Connecting WIFI Open Bluetooth Unread voice message USB insert tips Table 4 - DSSkey Icons Icons Description MWI Speed Dial Intercom Call Park Call forward 8
Key Event/DND Key Event/Call Hold Key Event/Call Transfer Key Event/Phonebook Key Event/Redial Key Event/Pickup Key Event/Join Key Event/Auto Redial On Key Event/Auto Redial Off Key Event/Call Forward Key Event/Call Logs Key Event/Flash Key Event/ Key Event/Headset Key Event/Release Key Event/Lock Phone Key Event/SMS Key Event/Call Back 9
Key Event/Hide DTMF Key Event/Power Light Key Event/Prefix Key Event/Hot Desking Key Event/Agent Key Event/End Key Event/Disposition Key Event/Escalate Key Event/Trace Key Event/Handfree Key Event/Answer Key Key Event/Private Hold URL & Action URL BLF List Multicast Unfold Collapse 10
6.2 Appendix II –Keyboard character query table Table 5 - Look-up Table of Characters Mode Icon Text Mode Numeric Key Button 1 2 3 4 5 6 7 8 9 0 ＊ Lower Case Alphabets # 1 2 3 4 5 6 7 8 9 0 ＊ # 11 Characters Of Each Press 1 2 3 4 5 6 7 8 9 0 * # @:;()<> abc def ghi jkl mno pqrs tuv wxyz (space) .
Upper Case Alphabets 1 2 3 4 5 6 7 8 9 0 ＊ Mixed type input # 1 2 3 4 5 6 7 8 9 0 ＊ # @:;()<> ABC DEF GHI JKL MNO PQRS TUV WZYX (space) .,*/+-:_= # ^!&$% 1 2abcABC 3defDEF 4ghIGHI 5jklJKL 6mnoMNO 7pqrsPQRS 8tuvTUV 9wzyxWZYX 0 .
6.3 Appendix III –LED Definition Table 6 - DSS KEY LED State Type Line Key BLF Presence DND MWI 13 LED Light LED State Off Line inactive Green On Line ready (Registered) Green Blinking Ringing Red Blinking Line is trying to register Red Blinking Line error (Registration failure) Red On Dialing/Line in use (Talking) Yellow Blinking Call holding Green On Subscription number is idle. Red On Subscription number is busy. Red On Subscription number is dialing.
7 Introduction to the User 7.1 Instruction of Keypad Instruction of the X7A Keypad 7.1.1 Picture 3 - Instruction of Keypad The above picture shows the keypad layout of the device. Each key provides its own specific function. User should refer to the illustration in this section about the usage of each key and the description in this document about each function.
triggered to provide special functions. #- Long presses this key to open the keyboard lock configuration. Navigate/OK The user can press the up/down navigation key to change the /Return Keys line or move the cursor in the screen list. On some Settings and text editing pages, the user can press the left/right navigation key to change options or move the cursor in the screen list to the left/right. 2 ○ A E OK key: Default is equivalent to soft button confirmation, user can customize the function.
7.2 Using Handset / Hands-free Speaker / Headphone Using Handset To talk over handset, user should lift the handset off the device and dial the number, or dial the number first, then lift the handset and the number will be dialed. User can switch audio channel to handset by lifting the handset when audio channel is opened in speaker or headphone.
information of the device;Slide up to exit the above information interface. Right slide can expand DSSkey, full screen display custom shortcut key information;Slide left to exit the above interface. Drag Long press the application icon in any interface, and you can drag it to any place. 7.4 Idle Screen Picture 4 - X7A default home screen The image above shows the default standby screen, which is the user interface in the most of the time.
7.
Picture 6 - WEB phone status 7.6 Application Instruction Table 8 - Application instruction Click this icon to enter the pre-dial number interface, and then dial the Dialer corresponding operation through the screen or keyboard. It has the function of sending and receiving email. After configuring the account, it can send and receive directly on the phone.Contacts for this Email account are automatically synchronized to the mailbox account.
Notes and records -- convenient for users to note events, and electronic post-it notes can be viewed at any time. Notepad Support search, add, delete, edit contacts and other functions. Contacts Support access to various websites. Browser Support call and non - call recording, and support export. Sound Recorder Display and view dates, create activity reminders, etc. Calendar There are four big options, including basic Settings, call Settings, advanced Settings and about the phone.
View configuration SD card, usb flash drive and system related files. Explorer Application management - you can install and uninstall android applications. Apkinstaller Turn on and off the disturb free configuration. DND When the answering machine is activated, the call will be automatically forwarded to the voicemail MWI Click this icon to enter the application list screen Application 7.7 Web Management Phone can be configured and managed on the web page of the phone.
Picture 7 - Landing page Users must correctly enter the user name and password to log in to the web page. The default user name and password are "admin". For the specific details of the operation page, please refer to page 11 Web configurations. 7.8 Network Configurations The device supports two kinds of network connection modes: wired network connection and wireless network connection. This section describes the wired network connection. For wireless network connection, refer to 10.5 wi-fi.
There are three common IP configuration modes about IPv4 Dynamic Host Configuration Protocol (DHCP) – This is the automatic configuration mode by getting network configurations from a DHCP server. Users need not to configure any parameters manually. All configuration parameters will be getting from DHCP server and applied to the device. This is recommended for most users.
Phone interface：To manually configure a line, the user can press the line key for a long time, or press the button in the function menu [Phone Settings] >> [Account] >> [Line] configuration, click “OK” to save the configuration. NOTICE! User must enter correct PIN code to be able to advanced settings to edit line configuration. (The default PIN is 123) The parameters and screens are listed in below pictures.
Picture 10 - Web SIP registration 25
8 Basic Function 8.1 Making Phone Calls Default Line The device provides twenty line services. If both lines are configured, user can make or receive phone calls on either line. If default line is configured by user, there will be a default line to be used for making outgoing call which is indicated on the top left corner. To change the default line, user can press left/right navigator buttons to switch between two lines.
Selecting a phone number from phonebook contacts (Refer to 10.2.1 Local contacts) Selecting a phone number from cloud phonebook contacts (Refer to 10.2.3 Cloud Phone Book) Selecting a phone number from call logs (Refer to 10.3 Call Log) Redialing the last dialed number Dial Number then Open Audio To make a phone call, user can firstly dial a number by one of the above methods.
Picture 13 - Open the voice channel and dial the number 28
Cancel Call While calling the number, user can press to end the audio channel by putting back the handset or pressing the hands-free button to drop the call. Picture 14 - Call number 8.2 Answering Calls When the phone is idle and there is a call, the user will see the call reminder screen as belowed.
pressing the hands-free button, or the [Answer] button. To divert the incoming call, user should press [Divert] button. To reject the incoming call, user should press [Reject] button. Talking 8.2.1 When the call is connected, user will see a talking mode screen as the following figure. Picture 16 - Talking interface Table 9 - Talking mode Number Name Description ① The current line The line currently used by the phone.
Call ④ ⑤ The duration of a call after it has established.Name on the other end Video Click to initiate video call.The duration of a call after it iconCall Record audio has been established. iconHD Click start recording and click end recording again.Call using G.722 voice coding calls when displayed HD voice icon. Make / Receive the Second Call The device can support up to two concurrent calls.
Picture 17 - The second call interface Second Outgoing Call To make a second call, user may press [Xfer] / [Conf] button to make a new call on the default line or press the line key to make new call on specific line. Then dial the number the same way as making a phone call. Another alternative for making second call is to pressing DSS Keys dial out from the configured Keys (BLF/Speed Dial).
Picture 18 - Two way calling User can press up/down navigator buttons to switch screen page, and switch call focus by pressing [Resume] button. Ending One Call User may hang up the current talking call by closing the audio channel or press [End] button. The device will return to single call mode in holding state. 8.
Picture 19 - Video interface WEB interface: enter [Phone Settings] >> [Features] >> [Basic Settings], and choose to configure the “Default Dial Mode” and “Default Ans Mode”.
Picture 20 - Video Settings 8.5 Redial Redial the last outgoing number: When the phone is in standby mode, press the redial button and the phone will call out the last number dialed. Call out any number with the redial key: Enter the number, press the redial key, and the phone will call out the number on the dial.
Picture 21 - Redial set 8.6 Dial-up Query Phone is defaulted to open the dial-up inquiry function, dial-out, enter two or more Numbers, dial the interface will automatically match call records, contacts in the number list, use the navigation key up and down keys can select the number, press the call out key or time out. 8.7 Auto-Answering User may enable auto-answering feature on the device and any incoming call will be automatically answered (not including call waiting).
Picture 22 - Line 1 enables auto-answering Picture 23 - The line has enabled auto-answering WEB interface： Log in the phone page, enter [Line] >> [SIP], select [SIP] >> [Basic settings], start auto-answering, and click apply after setting the automatic answering time.
Picture 24 - Web page to start auto-answering 8.8 Call Back The user can dial back the last call. If there is no call history, press the [Callback] button and the phone will say "can't process".
Picture 25 - Set the callback key on the phone Set the callback key through the web interface: Log in the phone page, enter the [Function Key] >> [Function Key] page, select the function Key, set the type as the function Key, and set the subtype as the callback, as shown in the figure: 39
Picture 26 - Set the callback key on the web page 8.9 Mute You can turn on mute mode during a call and turn off the microphone so that the local voice is not heard. Normally, mute mode will be automatically turned off at the end of a call. You can also turn on mute on any screen (such as the free screen) and mute the ringtone automatically when there is an incoming call. Mute mode can be turned on in all call modes (handles, headphones or hands-free). 8.9.
Picture 28 - Ringing mute Cancel ring tone mute: On the standby or incoming call screen, press the mute button again or volume up botton to cancel ring tone mute. It will no longer shows mute icon in upper right corner after cancel 8.10 .The phone mute icon is off Call Hold/Resume The user can press the [Hold] button to maintain the current call, and this button will become the [Resume] button, and the user can press the "resume" button to restore the call.
Picture 29 - Call hold interface 8.11 DND User may enable Do-Not-Disturb (DND) feature on the device to reject incoming calls (including call waiting). The DND can be enabled on line basis. Enable/Disable phone all lines DND, Methods the following： Phone interface：Default standby mode， 1) Press [DND] button to enter the DND setting interface, select line or phone to enable DND, the icon will become red . The phone status prompt bar will have a DND icon.
Picture 30 - Enable DND If the user wishes to enable/disable the uninterrupted function on a specific line, the user can set the uninterrupted function on the page of configuring the line. 1) Press [Phone Settings] >> [Call] >> [DND] button, Enter the [DND] editing interface. 2) Click the left/right navigation button to select the line to adjust the mode and state of "do not disturb", and then press the [OK] button to save.
Picture 33 - DND Settings The user turns on the DND for a specific route on the web page：Enter [Line] >> [SIP], select a [Line] >> [Basic settings], and enable DND.
Picture 34 - Line DND 8.12 Call Forward Call forward is also known as ‘Call Divert’ which is to divert the incoming call to a specific number based on the conditions and configurations. User can configure the call forward settings of each line.
number. Call Forward on Busy – When user is busy, the incoming call will be forwarded to the configured number. Call Forward on No Answer – When user does not answer the incoming call after the configured delay time, the incoming call will be forwarded to the configured number. Phone interface：Default standby mode 1) Press [Application] >> [Phone Settings] >> [Account] >> [Line] button, click any line to set up forward settings.
Picture 37 – Enable the call forwarding and configure the call forwarding number 4) Configure parameters by clicking Settings and enter the required information. When finished, press the [√] button to save the changes. WEB interface：Enter [Line] >> [SIP], Select a [Line] >> [Basic settings], and set the type, number and time of forwarding.
Picture 38 - Set call forward 8.13 Call Transfer When the user is talking with a remote party and wish to transfer the call to another remote party, there are three ways to transfer the call, blind transfer, attended transfer and Semi-Attended transfer. Blind transfer：Do not need to negotiate with the other side, directly transfer the call to the other side. Semi-Attended transfer.：When you hear the ring back, transfer the call to the other party.
Picture 39 - Transfer interface 8.13.2 Semi-Attended transfer During the call, the user presses the function menu button [transfer] or the transfer button on the phone to input the number to be transferred or press the contact button or the historical record button to select the number, and then press the call button. When the third party is not answered, press the transfer on the call interface to make the semi-attendance transfer or press the end button to cancel the semi-attendance transfer.
Picture 41 - Attended transfer 8.14 Call Waiting Enable call waiting: new calls can be accepted during a call. Disable call waiting: new calls will be automatically rejected and a busy tone will be prompted. Enable call waiting tone: when you receive a new call on the line, the tone will beep. The user can enable/disable the call waiting function in the phone interface and the web interface.
Picture 42 - Call waiting setting WEB interface: Enter [Phone Settings] >> [Features] >> [Basic Settings], enable/disable call waiting and call waiting tone.
Picture 44 - Web call waiting tone setting 8.15 Conference 8.15.1 Local Conference To conduct local conference, the user needs to log in the webpage and enter [Line] >> [SIP] >> [Basic settings].
Picture 45 - Local conference setting Two ways to create a local conference： 1） The device has two channels of communication. Press the conference button on the call interface. When selecting the conference number, select the other number that already exists.
8.15.2 Network Conference Users need server support for network conference.
then will enter the conference room. The two phones have established common calls. Press the conference button to invite new members to the conference. Follow the voice prompt to operate. Note: the upper limit of the number of participants in the network conference varies according to the server. 8.16 Call Park Call Park requires server support. Consult your system administrator for support.
Picture 50 - WEB set call park 8.17 Pick Up Picking-up requires server support. Consult your system administrator for support. You can use the Pick Up function to answer incoming calls from other users. The phone can pick up incoming calls by configuring DSSkey for BLF and setting the Pick Up code. In standby mode, click the "unfold" button and long press an editable key to enter the interface of function key setting.
incoming ring. Press the DSS key to pick up the phone. The caller picks up the call and speaks to it. WEB interface: Log in the phone webpage, enter the [Function Key] >> [Function Key] page, select a DSSkey, set the memory key type as memory key, the subtype as BLF/NEW CALL, and set the corresponding SIP line and pick up codes.
Picture 52 - WEB pick up setting 8.18 Anonymous Call 8.18.1 Anonymous Call The phone can set up anonymous calls to hide the calling number and the calling name. You can see anonymity in the context of [Phone Settings] >> [Account] >> [Line] >> [Advanced Settings] >> [Anonymous call edition]. The default is none, which is off, and RFC3323 and RFC3325 are optional. Select any one to open the anonymous call.
Setting to enable anonymous calls also corresponds to the SIP line. That is, the setting under the SIP1 page can only take effect on the SIP1 line. Picture 54 - Enable Anonymous web page call The following is a transcript of an anonymous call received by the phone. Picture 55 - Anonymous call log 8.18.2 Ban Anonymous Call The device can be set to prohibit anonymous calls, that is anonymous calls to the number will be directly rejected.
Picture 56 - Anonymous calls are not allowed on the phone On the web page [Line] >> [SIP] >> [Advanced Settings], also can disable anonymous calls. The setup to disable anonymous calls also corresponds to the SIP line. That is, the setting under the SIP1 page can only take effect on the SIP1 line.
Picture 57 - Page Settings blocking anonymous call 8.19 Hotline The device supports hotline dialing. After setting up the hotline dialing, directly pick up the handset, hands-free, earphone, etc., and the phone will automatically call according to the hotline delay time. In the phone [Phone Settings] >> [Account] >> [Line] >> [Basic Settings], click to enter. 61 Then set the hotline for each SIP line, which is off by default.
Picture 58 - Phone hotline setting interface On the website [Line] >> [SIP] >> [Basic Settings], can also set up a hotline. The setup hotline also corresponds to the SIP line. That is, the hotline set in the SIP1 webpage can only be activated in the SIP1 line.
9 Advance Function 9.1 BLF (Busy Lamp Field) 9.1.1 Configure the BLF Functionality Page interface: log in the phone page, enter the [Function key] >> [Function key] page, select a DSS key, set the function key type as memory key, choose subtype among BLF/NEW CALL, BLF/BXFER, BLF/AXFER, BLF/CONF, set BLF/DTMF value as the number which is subscribed, set the corresponding SIP line. The pickup number is provided by the server. The specific use of reference 8.17 Pick up.
Phone interface: Click unfold, long press a function key to enter the function key Settings interface, key function key types of memory, a subtype of BLF/NEW CALL, BLF/BXFER, BLF/AXFER, BLF/CONF, BLF/DTMF, the values to be subscription number, and set up corresponding SIP lines.
Use the BLF Function 9.1.2 The BLF, also known as a "busy light field," notifies the user of the status of the subscribed object and is used by the server to pick up the call. BLF helps you monitor the other person's status (idle, ringing, talking, off). BLF function： Monitor the status of subscribed phones. Call the subscribed number. Transfer calls to the subscribed number. Pick up incoming calls from subscribed number. 1） Monitors the status of subscribed phones.
Configure BLF List function: log in the phone page, enter the [Line] >> [SIP] >> [Advanced settings] page, open the BLF List, and configure the BLF List number. Picture 62 - Configure the BLF List functionality Use the BLF List function: when the configuration is completed, the phone will automatically subscribe to the contents of the BLF List group. Users can monitor, call and transfer the corresponding number by pressing the BLF List key.
Picture 63 - BLF List number display 9.3 Record The device supports recording during a call. 9.3.1 Local Record When using local recording, it is necessary to start recording on the phone page [Application] >> [Manage recording], select the local type and set the voice coding.
Picture 64 - WEB local recording Local recording steps: Open the recording on the web page, and set the recording type as local recording. Set DSSkey type as key event and type as record in the phone/web interface. Set up one line call and press the recording key (set DSSkey). End the recording. End the call. View local recording: Enter [Application] >> [Sound Recorder] Enter view the recording file.
selected. The web is as follows: Picture 65 - Web server recording Note: to be used with Fanvil recording software. Please refer to the documentation for specific usage: Call Recording Configuration and Use Description http://www.fanvil.com.cn/Uploads/Temp/download/20180928/5badccd249853.pdf 9.3.3 SIP INFO Record The phone is registered with a server that supports SIP INFO recording.
and Use Description http://www.fanvil.com.cn/Uploads/Temp/download/20180928/5badccd249853.pdf Picture 66 - Web SIP info recording 9.4 Agent Agent (Agent function) of the phone can be realized: when multiple people use a device for Agent services at different times, he or she can quickly register his or her SIP account on the same server. The Agent functions of the phone can be divided into Normal and Hotel Guest. The Hotel Guest mode requires server support.
Picture 67 - Configure the agent account in normal mode Picture 68 - Configure the proxy account-hotel Guest mode Table 11 - Agency mode Parameter Description Normal mode Number Set the proxy account number. User Set the proxy account number to verify the user name. Password Set the proxy account number to verify the password. Line Select the SIP line. CallLog Users can choose to save all types, or delete. Hotel Guest mode 71 Number Set the proxy account number.
The user can select the status of the number, the optional Status status is: login, logout, invalid, valid, SMS. Using agent functions: 1） When the phone has been configured on SIP server, fill in the correct number and user name password, click login and then the phone can be registered to the SIP server; 2） After registration, click logout and the phone can delete the user name and password, and log out of the SIP account.
Picture 70 - Web Intercom configure Table 12 - Intercom configure Parameter Description Enable Intercom When intercom is enabled, the device will accept the incoming call request with a SIP header of Alert-Info instruction to automatically answer the call after specific delay.
Picture 71 - Multicast Settings Page Table 13 - MCAST Parameters on Web Parameters Description Normal Call Priority Define the priority of the active call, 1 is the highest priority, 10 is the lowest. Enable Page Priority The voice call in progress shall take precedence over all incoming paging calls. Name Listened multicast server name Host: port Listened multicast server’s multicast IP address and port.
Click Apply. Set up the name, host and port of the receiving multicast on the web page of [Phone Settings] >> [MCAST]. Press the DSSKEY of Multicast Key which you set. Receiver will receive multicast call and play multicast automatically. 9.7 SCA（Shared Call Appearance） Users need the support of server end to use SCA function. You can refer to http://www.fanvil.com/Uploads/Temp/download/20180920/5ba38181e4e4b.
Picture 72 - Register BroadSoft account After the phone registers on the BroadSoft server, a server type needs to be set. Specifically, log in to the web page of the phone, choose [Line] >> [SIP] >> [Advanced Settings] and set Specific Server Type to BroadSoft, as shown in the following figure.
Picture 73 - Set BroadSoft server If a Fanvil phone needs to use the SCA function, enable it for the phone set. Specifically, log in to the webpage of the phone set, choose [Line] >> [SIP] >> [Advanced Settings], and select Enable SCA. If SCA is not enabled, the registered line is private line.
Picture 75 - Set Private Hold Function Key After each phone registered with the BroadSoft server is configured as above, the SCA function can be used. 2）LED Status To facilitate viewing the call status of a group, configure lines whose DSS Key is SCA. The following table describes the LEDs of lines in different states.
Bridge-active (Barge-in) Steady green Steady red Bridge-held Steady green Steady red 3） Shared Call Appearance(SCA) The following lists a couple of instances to facilitate understanding. In the following scenarios, the manager and secretary register the same SCA account and the account is configured based on the preceding steps. Scenario 1: When this account receives an incoming call, the phone sets of both the manager and the secretary will receive the call and ring.
Picture 76 - SMS icon Send messages: Go to [Application] >> [SMS]. Users can create new messages, select lines and send numbers. After editing is complete, click Send. View SMS: Use the navigation keys to select the standby icon [message] After selecting, press the navigation key [OK] to enter the SMS inbox interface. Select the unread message and press [OK] to read the unread message. Reply to SMS: Use the navigation keys to select the standby icon [Message].
Picture 77 - New Voice Message Notification Voice message icon To listen to a voice message, the user must first configure the voicemail number. After the voicemail number is configured, the user can retrieve the voicemail of the default line. When the phone is in the default standby state, The voicemail icon displays the number of unread voicemail messages.
Picture 79 - Configure voicemail number 9.9 SIP Hotspot SIP hotspot is a simple but practical function. With simple configurations, the SIP hotspot function can implement group ringing. SIP accounts can be expanded. Set a phone as a SIP hotspot and other phones (B and C) as SIP hotspot clients. When somebody calls phone A, phone A, B, and C all ring. When any phone answers the call, other phones stop ringing. The call can be answered by only one phone.
Picture 80 - Register SIP account Table 15 - SIP hotspot Parameters Parameters Description If your phone is set to “SIP hotspot server”, Device Table will display as Client Device Table SIP hotspot 83 Device Table which connected to your phone. If your phone is set to “SIP hotspot client”, Device Table will display as Server Device Table which you can connect to.
Enable hotspot Mode Monitor Type Monitor Address Remote Port Set it to be Enable to enable the feature. Choose hotspot, phone will be a “SIP hotspot server”; Choose Client, phone will be a “SIP hotspot Client” Either the Multicast or Broadcast is ok. If you want to limit the broadcast packets, you’d better use broadcast. But, if client choose broadcast, the SIP hotspot phone must be broadcast. The address of broadcast, hotspot server and hotspot client must be same. Type the Remote port number.
Picture 81 - SIP hotspot server configuration Configure SIP hotspot client: As a SIP hotspot client, no SIP account needs to be set. The Phone set will automatically obtain and be configured a SIP account. On the SIP Hotspot tab page, set Mode to Client. The values of other options are the same as those of the hotspot.
Picture 82 - SIP hotspot client configuration As the hotspot server, the default extension number is 0. When the phone is used as the client, the extension number is increased from 1, you can view the extension number through the [SIP Hotspot] page. Call extension number: The hotspot server and the client can dial each other through the extension number. For example, extension 1 dials extension 0.
10 Phone Settings 10.1 10.1.1 Basic Settings Language The user can set the phone language through the phone interface and web interface. Phone interface：After resetting the factory settings, the user needs to set the language; when setting the language during standby, go to [Settings] >> [Personal] >> [Language&input] Settings, as shown in the figure.
Picture 84 - Language setting on Web page The function box on the right side of the web interface language setting box is “Synchronize language to phone”; if selected, the phone language will be synchronized with the webpage language. If it is not selected, it will not be synchronized. 10.1.2 Time & Date Users can set the phone time through the phone interface and web interface.
0P icture 86 - Set time & date on webpage Table 16 - Time Settings Parameters Parameters Description Mode Auto/Manual Auto: Enable network time synchronization via SNTP protocol, default enabled.
Manual: User can modify data manually.
Picture 87 - Set screen parameters on phone 10.1.3.1 Brightness and backlight Set the brightness level in use from 1 to 16, [<] or [>] switch brightness level. Set the brightness level in the energy-saving mode from 0 to 16, [<] or [>] switch the brightness level. Set the backlight time to 30 seconds by default. You can turn it off or select 15 seconds /30 seconds /45 seconds /60 seconds /90 seconds /120 seconds. The screen saver can be turned on or off by default.
Picture 89 - Phone screen saver 10.1.4 Ring When the device is in the default standby mode, Enter [Phone Settings] >> [Media] >> [Sound] item till you find [Tone] item. Enter [Sound] >> [Tone] set promote tone The prompt tone contains Settings such as caller ring, notification ring, touch prompt tone, etc. 10.1.5 Voice Volume When the device is in the default standby mode, Enter [Phone Settings] >> [Media] >> [Sound] item till you find [Volume] item.
By default, the phone book is empty, and users can add manually or add contacts to the phone book from the call log (or cloud phone book). NOTICE! The device can save up to total 2000 contact records. Picture 90 - Local Phone book When there are contact records in the phone book, the contact records will be arranged in the alphabet order. User may browse the contacts with up/down navigator keys. The record indicator tells user which contact is currently focused.
Picture 91 - Add New Contact User can edit a contact by pressing [Option] >> [Edit] button. To delete a contact, user should move the record indicator to the position of the contact to be deleted, press [Option] >> [Delete] button and confirm with [OK]. 10.2.1.2 Add / Edit / Delete Group By default, the group list is empty. Users can create their own group, edit group names, add or remove contacts from the group, and delete groups. Add group.
Picture 92 - Group List 10.2.2 Black list The device supports blacklist, such as the number added to the blacklist, the number of calls directly refused to the end, the end of the phone shows no incoming calls. (Blacklisted Numbers can be called out normally) There are multiple ways to add a number to Blacklist on the device. It can be added directly on [Contacts] icon >> [Group] icon>> [Blacklist]. Select any number in the phone book (both local and network) for configuration addition.
Select any number in the phone book (both local and network) for configuration addition. Select any number in the call log for configuration addition. Picture 94 - Web Blacklist 10.2.3 Cloud Phone Book 10.2.3.1 Configure Cloud Phone book Cloud phonebook allows user to configure the device by downloading a phonebook from a cloud server. This is convenient for office users to use the phonebook from a single source and save the effort to create and maintain the contact list individually.
Picture 95 - Cloud phone book list 10.2.3.2 Downloading Cloud Phone book In cloud phone book screen, user can open a cloud phone book by pressing the network phonebook. The device will start downloading the phone book. The user will be prompted with a warning message if the download fails, Once the cloud phone book is downloaded completely, the user can browse the contact list and dial the contact number same as in local phonebook. Picture 96 - Browsing Contacts in Cloud Phone book 10.
Each call log record is presented with ‘call type’ and ‘call party number / name’. User can check further call log detail by pressing [Info] icon and dial the number with pressing the call log, or add the call log number to phonebook with pressing [Info] Icon >> [Add to Contact]. User can delete a call log by pressing [Delete] button and can clear all call logs by pressing [Delete All] button.
customized (expansion keys are not supported). After expansion, there will be 28 Function DSSkey, a total of four pages. Users can customize and configure each DSSKEY key on each page. Users can add/delete DSSkey pages through the webpage, and can use the page switch key to switch DSSkey pages. In addition, users can also long press each shortcut key, modify the corresponding key settings.
More detailed information refers to 12.23 Function Key and 6.3 Appendix III –LED Definition . 10.5 Wi-Fi The device supports wireless Internet access and has built-in Wi-Fi without external devices. When the device is in the default standby mode, Press [Application] till you find the [Settings] item. Enter [Wi-Fi] item. Enable the Wi-Fi to search the current wireless network automatically. Select to the available network, enter the user name and password to connect successfully.
10.6 10.6.1 Headset Wired Headset The device supports wired earphone with RJ9 interface, which can play incoming call sound and talk with earphone. After the phone is connected to the headset, the default DSS key of headset will be green light which indicates that the headset can be used normally. On the webpage [Phone settings] >> [Features], you can set the headset answering function, and the ring tone for headset. Picture 101 - Headset function settings 10.6.
external devices. When the device is in the default standby mode, Press [Application] till you find the [Settings] item. Press [Bluetooth] item to enter the setup interface. Enable Bluetooth and select Paired Device. Picture 102 - Bluetooth Settings Screen The use of Bluetooth headset can be divided into three types: call answering; Hang up; Bluetooth redial.
to cancel the call. Bluetooth redial When the Bluetooth headset is connected, double-click the answer button to redial the number dialed last time. NOTICE! some models do not support double - click redial function. Whether this function is supported or not, you can check the instruction of the headset, or connect the Bluetooth headset to the phone, and double-click the answer button to see whether it will redial. 10.7 10.7.
Picture 104 - Configure Advanced Line Options 10.7.2 Network Settings 10.7.2.1 Network Settings Phone access [Phone Settings] >> [Network] >> [Ethernet], you can configure the SIP line on the phone. There are 3 connection mode options: DHCP, PPPoE and Static IP. Picture 105 - DHCP network mode When using DHCP mode, phone will get the IP address from DHCP server (router). Obtain DNS Server automatically: It is enabled as default.
Picture 106 - PPPoE network mode When using PPPoE, phone will get the IP address from PPPoE server. User: PPPoE user name. Password: PPPoE password. Picture 107 - Static IP network mode When using Static IP mode, user must configure the IP address manually. IP Address：Phone IP address. Subnet Mask: sub mask of your LAN. IP Gateway：The gateway IP address. Phone could access the other network via it. Primary DNS：Primary DNS address. The default is 8.8.8.8, Google DNS server address.
10.7.2.2 QoS & VLAN Access [ Phone Settings]>> [Network]>> [ Advance] LLDP Link Layer Discovery Protocol. LLDP is a vendor independent link layer protocol used by network devices for advertising their identity, capabilities to neighbors on a LAN segment. Phone could use LLDP to find the VLAN switch or other VLAN devices and use LLDP to learn feature to apply the VLAN ID from VLAN switch to phone its self. CDP Cisco Discovery Protocol.
10.7.2.3 Web Server Type Access [Phone Settings]>> [ Network]>> [ Service Port] to configure the Web Server mode. Configure the Web Server mode to be HTTP or HTTPS and will be activated after the reboot. Then user could use http/https protocol to access pone web page. Picture 108 - The phone configures the web server type 10.7.3 Set The Secret Key When the device is in the default standby mode, Select [Phone Settings]>> [ System]>> [ Password] Click [ Password] to change password.
10.7.4 Maintenance Phone Webpage: Login and go to [System] >> [Auto provision]. Picture 110 - Page auto provision Settings LCD：Enter [Phone Settings] >> [System] >> [Maintain] >> [Auto Provision].
Picture 111 - Phone auto provision settings Fanvil devices support SIP PnP, DHCP options, Static provision, TR069. If all of the 4 methods are enabled, the priority from high to low as below: PNP>DHCP>TR069> Static Provisioning Transferring protocol: FTP、 TFTP、 HTTP、 HTTPS Details refer to Fanvil Auto Provision in http://www.fanvil.com/Uploads/Temp/download/20180920/5ba3816f8d5f0.
DHCP Option Confiugre DHCP option, DHCP option supports DHCP custom Option Value option | DHCP option 66 | DHCP option 43, 3 methods to get the provision URL. The default is Option 66. Custom Option Value Enable DHCP Option 120 Custom Option value is allowed from 128 to 254. The option value must be same as server define. Use Option120 to get the SIP server address from DHCP server. SIP Plug and Play (PnP) Whether enable PnP or not.
ACS User ACS server username (up to is 59 character) ACS Password ACS server password (up to is 59 character) Enable TR069 Warning If TR069 is enabled, there will be a prompt tone when Tone connecting. TLS Version TLS version (TLS 1.0, TLS 1.1, TLS 1.2) INFORM Sending Period INFORM signal interval time. It ranges from 1s to 999s STUN Server Address Configure STUN server address STUN Enable To enable STUN server for TR069 10.7.
Picture 112 - Web page firmware upgrade LCD interface: go to [Menu] >> [Maintain] >> [Upgrade] . Picture 113 - Firmware upgrade information display Table 19 - Firmware upgrade Parameter Description Upgrade server Enable automatic upgrade, If there is a new version txt Enable Auto Upgrade and new software firmware on the server, phone will show a prompt upgrade message after Update Interval. Upgrade Server Address1 Set available upgrade server address.
on hardware. All Spaces in the filename are replaced by underline. The URL requested by the phone is HTTP:// server address/vendor_Model_hw10 .txt：The new version and the requested file should be placed in the download directory of the HTTP server, as shown in the figure: TXT file format must be UTF-8 vendor_model_hw10.TXT The file format is as follows： Version=1.6.3 #Firmware Firmware=xxx/xxx.
10.7.6 Factory Reset The phone is in default standby mode. Press [Phone Settings] to find [System]>> [Maintain]>> [ Phone Reset]. Press the [Reset] button to select the file to be cleared. Press [OK] to clear after completion. When you select clear configuration file and clear all, the phone will restart automatically after clearing.
11 Web Configurations 11.1 Web Page Authentication The user can log into the web page of the phone to manage the user's phone information and operate the phone. Users must provide the correct user name and password to log in. 11.
Clear Configurations Select the module in the configuration file to clear. SIP: account configuration. AUTOPROVISION: automatically upgrades the configuration TR069:TR069 related configuration MMI: MMI module, including authentication user information, web access protocol, etc. DSS Key: DSS Key configuration Clear Tables Select the local data table to be cleared, all selected by default. Reset Phone The phone data will be cleared, including configuration and database tables. 11.
12 Network >> Basic This page allows users to configure network connection types and parameters. 12.1 Network >> Service Port This page provides settings for Web page login protocol, protocol port settings and RTP port. Picture 116 - Service Port Settings Table 20 - Service port Parameter Description Web Server Type Reboot to take effect after settings. Optionally, the web page login is HTTP/HTTPS.
RTP Port Quantity 12.2 Number of calls. Network >> Advanced Advanced network Settings are typically configured by the IT administrator to improve the quality of the phone service. For configuration, query the 10.7 advanced Settings. 12.3 Line >> SIP Configure the Line service configuration on this page. Table 21 - Line configuration on the web page Parameters Description Register Settings Line Status Display the current line status at page loading.
Server Port Enter the SIP server port, default is 5060 Transport Protocol Set up the SIP transport line using TCP or UDP or TLS. Registration Expiration Set SIP expiration date. SIP Proxy Server Address Enter the IP or FQDN address of the SIP proxy server. Proxy Server Port Enter the SIP proxy server port, default is 5060. Proxy User Enter the SIP proxy user. Proxy Password Enter the SIP proxy password. Backup Proxy Server Address Enter the IP or FQDN address of the backup proxy server.
the server Server Conference Number Set the conference room number when conference type is set to be Server Subscribe For Voice Message Enable the device to subscribe a voice message waiting notification, if enabled, the device will receive notification from the server if there is voice message waiting on the server Voice Message Number Set the number for retrieving voice message Voice Message Subscribe Period Set the interval of voice message notification subscription Enable Hotline Enable ho
Signal Retry Counts The number of attempts that the SIP Request considers proxy unavailable under multiple proxy scenarios. Codecs Settings Set the priority and availability of the codecs by adding or remove them from the list. Video Codecs Select video code to preview video. Advanced Settings Use Feature Code When this setting is enabled, the features in this section will not be handled by the device itself but by the server instead.
status of a group. Multiple BLF lists are supported. Response Single Codec If setting enabled, the device will use single codec in response to an incoming call request BLF Server The registered server will receive the subscription package from ordinary application of BLF phone. Please enter the BLF server, if the sever does not support subscription package, the registered server and subscription server will be separated.
Convert URI Convert not digit and alphabet characters to %hh hex code Use Quote in Display Name Whether to add quote in display name, i.e. “Fanvil” vs Fanvil Enable GRUU Support Globally Routable User-Agent URI (GRUU) Sync Clock Time Time Sync with server Enable Inactive Hold With the post-call hold capture package enabled, you can see that in the INVITE package, SDP is inactive.
with MAC or not. BLF Dialog Strict Match Whether to enable accurate matching of BLF sessions. PTime(ms) Set whether to bring ptime field, default no. SIP Global Settings Strict Branch Set up to strictly match the Branch field. Enable Group Set open group. Enable RFC4475 Set to enable RFC4475. Enable Strict UA Match Enable strict UA matching. Registration Failure Retry Time Set the registration failure retry time. Local SIP Port Modify the phone SIP port.
current call to a third party Blind Transfer on Onhook After the user enters the number, hang up the handle or turn off the hands-free function to transfer the current call to a third party. Attended Transfer on Onhook Hang up the handle or press the hands-free button to realize the function of attention -transfer, which can transfer the current call to a third party. Attended Transfer on Conference Onhook During a three-way call, hang up the handle and the remaining two parties remain on the call.
Prefix mode supports a maximum of 30 digits. Note: Two different special characters are used. x -- Matches any single digit that is dialed. [ ] -- Specifies a range of numbers to be matched. It may be a range, a list of ranges separated by commas, or a list of digits. Destination Set Destination address. This is for IP direct. Port Set the Signal port, and the default is 5060 for SIP. Alias Set the Alias. This is the text to be added, replaced or deleted. It is an optional item.
Picture 120 - Dial rules table (2) Example 3: Addition -- Two examples are shown. In the first case, it is assumed that 0 must be dialed before any 11 digit number beginning with 13. In the second case, it is assumed that 0 must be dialed before any 11 digit number beginning with 135, 136, 137, 138, or 139. Two different special characters are used. x -- Matches any single digit that is dialed. [] -- Specifies a range of numbers to be matched.
Table 25 - Set the line global configuration on the web page Parameters Description STUN Settings Server Address Set the STUN server address Server Port Set the STUN server port, default is 3478 Binding Period Set the STUN binding period which can be used to keep the NAT pinhole opened. SIP Waiting Time Set the timeout of STUN binding before sending SIP messages Certification File TLS Certification File Upload or delete the TLS certification file used for encrypted SIP transmission. 12.
Display Report Options on web Whether to display the VQ report data for the last call through the web page. 12.9 Phone settings >> Features Configuration phone features. Table 27 - General function Settings Parameters Description Basic Settings Enable Call Waiting Enable this setting to allow user to take second incoming call during an established call. Default enabled. Enable Call Transfer Enable Call Transfer.
Ban Outgoing If you select Ban Outgoing to enable it, and you cannot dial out any number. Hide DTMF Configure the hide DTMF mode. Enable CallLog Select whether to save the call log. Enable Restricted Incoming List Whether to enable restricted call list. Enable Allowed Incoming List Whether to enable the allowed call list. Enable Restricted Outgoing List Whether to enable the restricted allocation list. Enable Country Code Whether the country code is enabled.
without opening audio channel. If enabled, up to 10 simultaneous calls can exist Enable Multi Line on the phone, and if disabled, up to 2 simultaneous calls can exist on the phone. Line Display Format Custom line format：SIPn/SIPn：xxx/xxx@SIPn Contact As White List Type NONE/BOTH/DND White List/FWD White List Block XML When Call Disable XML push on call. When SIP notify enabled, the phone displays the information when it receives the relevant notify content.
the current call is intercom call, the phone will reject the second intercom call Response Code Settings DND Response Code Set the SIP response code on call rejection on DND Busy Response Code Set the SIP response code on line busy Reject Response Code Set the SIP response code on call rejection Password Dial Settings Enable Password Dial Enable Password Dial by selecting it, When number entered is beginning with the password prefix, the following N numbers after the password prefix will be hidden as
left/retained. Notification Popups Display Missed Call Popup No incoming call popup prompt after opening, no popup prompt when closing, open by default. Voice message popup prompt is not answered Display MWI Popup after opening, and it is opened by default if there is no popup prompt when closing. There is a popup prompt when the WIFI adapter Display Device Connect Popup is connected. There is no popup prompt when the WIFI adapter is closed. It is on by default.
Opus playload type Set Opus load type, range 96~127. Set Opus sampling rate, including opus-nb (8KHz) OPUS Sample Rate and opus-wb (16KHz). ILBC Payload Type Set the ILBC Payload Type, the value must be 96~127.
SIP signaling. You can specify up to 10 multicast listening addresses. Table 29 - Multicast parameters Parameters Description Normal Call Priority Define the priority of the active call, 1 is the highest priority, 10 is the lowest. Enable Page Priority The voice call in progress shall take precedence over all incoming paging calls. Name Listened multicast server name Host: port Listened multicast server’s multicast IP address and port. 12.
12-Hour Clock Set the time display in 12-hour mode Date Format Select the time/date display format Daylight Saving Time Settings Local Choose your local, phone will set daylight saving time automatically based on the local DST Set Type Choose DST Set Type, if Manual, you need to set the start time and end time. Fixed Type Daylight saving time rules are based on specific dates or relative rule dates for conversion. Display in read-only mode in automatic mode.
Picture 121 - Tone settings on the web 12.15 Phone settings >> Advanced User can configure the advanced configuration settings in this page. Screen Configuration. Enable Energy Saving Backlight Time Screen Saver LCD Menu Password Settings. The password is admin by default. Keyboard Lock Settings. Configure Greeting Words The greeting message will display on the top left corner of the LCD when the device is idle, which is limited to 16 characters. The default chars are ‘VOIP PHONE’.
To edit a contact, click on the checkbox in front of the contact, the contact information will be copied to the contact edit boxes, press “Modify” button after finished editing. To delete one or multiple contacts, check on the checkbox in front of the contacts wished to be deleted and click the “Delete” button, or click the “Clear” button with selecting any contacts to clear the phonebook.
Search Base (must) Access username (optional) Access password (optional) Note! Refer to the LDAP technical documentation before creating the LDAP phonebook and phonebook server. http://www.fanvil.com/Uploads/Temp/download/20180920/5ba382eb399eb.pdf Web page preview Phone page supports preview of Internet phone directory and contacts After setting up the XML Voip directory or LDAP, Select [Phone book] >> [Cloud phone book] >> [Cloud phone book] to select the type.
12.18 Phonebook >> Call List Restricted Incoming Calls： It is similar like a blacklist. Add the number to the blacklist, and the user will no longer receive calls from the stored number until the user removes it from the list. Users can add specific Numbers to the blacklist or add specific prefixes to the blacklist to block calls with all Numbers with this prefix. Allowed Incoming Calls： When DND is enabled, the incoming call number can still be called.
The user can also save the number in the call record to his/her phone book or add it to the blacklist/whitelist. Users can also dial the web page by clicking on the number in the call log. Users can also download call records conditionally and save them locally. 12.22 Function Key >> Function Key Function Key Configuration： One-key transfer Settings: establish new call, blind transfer, attention-transfer, one-key three-party, Play DTMF.
pressing Line Key. Key Event User can select a key event as a shortcut to trigger. For example: MWI / DND / Release / Headset / Hold / etc. DTMF It allows user to dial or edit dial number easily. URL Open the specific URL directly. Multicast Configure the multicast address and audio codec. User presses the key to initiate the multicast. Action URL The user can use a specific URL to make basic calls to the phone. XML browser Users can set the DSS Key for specific URL download and other operations.
/Pickup/MWI/Join/CallLog/Release/Missed/Pause/Dialed/ Headset/Video/Audio/Remote XML/DSS Key/ln/Next line /Prev line Ringing Answer/Forward/Reject/Mute/Release/Headset/Video/Audio/ DSS key Hold/Transfer/Conference/End/Mute/Release/New Call/ Talking Local Contacts/Listen/CallLog/Next call/Prev call/ Private/Headset/Video/Audio/DSS Key Transfer Alerting End/Transfer/Headset/Release/DSS Key Redial/Delete/Exit/2aB/Dial/Local Contacts/Transfer/ Transfer Dialer CallLog/Clear/Missed/Dialed/Pause/Headset/Vid
12.25 Application >> Manage Recording See 9.3 Record for details of recording. 12.26 Security >> Web Filter The user can set up a configuration management phone that allows only machines with a certain network segment IP access.
Picture 125 - Web Filter Table Add and remove IP segments that are accessible; Configure the starting IP address within the start IP, end the IP address within the end IP, and click [Add] to submit to take effect. A large network segment can be set, or it can be divided into several network segments to add. When deleting, select the initial IP of the network segment to be deleted from the drop-down menu, and then click [Delete] to take effect.
12.28 Security >> Device Certificates Select the device certificate as the default and custom certificate. You can upload and delete uploaded certificates. Picture 127 - Device certificate setting 12.
Picture 128 - Network firewall Settings Through this page can set whether to enable the input, output firewall, at the same time can set the firewall input and output rules, using these Settings can prevent some malicious network access, or restrict internal users access to some resources of the external network, improve security. Firewall rule set is a simple firewall module. This feature supports two types of rules: input rules and output rules.
similar to *.*.*.0, such as: 192.168.1.0. The destination address can be either the specific IP Dst Address address or the full address 0.0.0.0; It can also be a network address similar to *.*.*.0, such as: 192.168.1.0. Is the source address mask. When configured as Src Mask 255.255.255.255, it means that the host is specific. When set as 255.255.255.0, it means that a network segment is filtered. Is the destination address mask. When configured as Dst Mask 255.255.255.255, it means the specific host.
13 Trouble Shooting When the phone is not in normal use, the user can try the following methods to restore normal operation of the phone or collect relevant information and send a problem report to Fanvil technical support mailbox. 13.1 Get Device System Information Users can get information by pressing the [Menu] >> [Status] option in the phone.The following information will be provided: The network information Equipment information (model, software and hardware version), etc. 13.
Picture 131 - Screenshot 13.5 Network Packets Capture Sometimes it is helpful to dump the network packets of the device for issue identification. To get the packets dump of the device, user needs to log in the device web portal, open page [System] >> [Tools] and click [Start] in “Network Packets Capture” section. A pop-up message will be prompt to ask user to save the capture file.
device during the period have been dumped to the saved file.
Picture 132 - Web capture User may examine the packets with a packet analyzer or send it to Fanvil support mailbox. 13.6 Get Log Information Log information is helpful when encountering an exception problem.
source. 2. If you saw “POST MODE” on the device screen, the device system image has been damaged. Please contact location technical support to help you restore the phone system. Device could not register to a 1. Please check if device is well connected to the network. The service provider network Ethernet cable should be connected to the [Network] port NOT the [PC] port. If the cable is not well connected to the network icon [WAN disconnected] will be flashing in the middle of the screen. 2.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
