Installation Manual
Installation
................................................12
Trail Camera E2
User Manual
Content
Few Words From EZETAI
Product Introduction
Structure
Components
Parameter
Function
Operation
.........................1
..................................1
...................................................1
.............................................3
..................................................3
.....................................................4
...................................................9
Warranty
..................................................16
QA
...........................................................15
Precaution
...............................................15
Contact Us
................................................16
Few Words From EZETAI
First of all, thank you for choosing . We are grateful for your trust in our products.
EZETAI has been studied cameras for decades. We have continuously designed
several models of trail camera for different needs based on our research. We
engage to provide the right product to the right customer.
EZETAI believes in Connection. We would like to build a little lovely community
where we could connect with each other and share our lives, our emotions, our
experience, our joy, and our sadness. Thank you for joining us.
welcome to EZETAI.
To be continued...
Product Introduction
E2 Trail Camera is an advanced model for daily use. If you are interested
in wildlife monitoring or you would like to see who are the secret visitors in your
garden, E2 Trail Camera is the perfect choice for you.
1. Structure
2. Components
Micro USB Cable Fixation Kit Installation Belt
3. Parameter
Photo Series
You can set the photo quantity
when the camera is activated
1 photo
(default)
2 photos in
series
3
10 photos in
series
photos in
series
Video
Resolution
You can choose different video
resolution
2688*1520P
20FPS
1920*1080P
1280*720P
(default)
720*480P
640*480P
TL Video
(1)
Resolution
You can choose the resolution of
time lapse video
8MP (3840*
2160P)
3MP (2304*
1296P)
5MP(3072*
1728P)
default
Photo
Resolution
You can choose different photo
resolution
1
6
20MP
MP
12MP
8MP
5MP
(default)
Operation
1.
Getting Started
Installation
If you want to put the camera on the wall, the Fixation Kit is
ready for you：
3. Fix the Fixation Kit by following the picture;
4. Put the camera at the position you have chosen and fix the camera with screws;
2. Put the camera on the bottom of the tree;
3. Go to the other side of the tree, pass the belt through the buckles by following
the picture;
4.
Adjust the position of the camera then tighten the belt;
5. If you afraid that the camera would fall, you could also use the Fixation Kit and
the Installation Belt together to make sure that the camera is sturdily fixed on the
right position.
1. Mark the installation position with the help of the metal plate and make holes in
the wall;
2. Put the green components in the holes;
Working Temperature -22°F - 158°F
Memory Card Type
Up to 256G TF Card (Class
10),TF Card is not include
Power Supply Type Battery/External
Battery Type
AA Battery
Working Voltage 6V
External Power Supply DC 6V
Standby Time
Up to 6 Months;
Only be achieved if the power
supply is sufficient for 8pcs batteries
Photo Format JPEG
Photo Resolution 20MP/1
Image Sensor 4.0MP CMOS sensor
6MP/12MP/8MP/5MP
Video Resolution 2.7K/1080P/720P/D1/VGA
Detection Angle Up to 120 °
LCD size 2.4” LCD
Detection Distance 80ft (day), 65ft (night)
Fill Light LED Wavelength 940nm (No Glow)
Fill Light LED Quantity 48 pcs
Trigger Time 0.2s - 0.5s
Waterproof Level IP66
4. Function
Mode
You could choose the working
mode of E2
Photos
(default)
Videos
Photos &
Videos
Video
Length
You can adjust the video length
10 seconds
(default)
3 seconds min.
10 minutes
max.
Audio
Recording
You can decide if you want the
camera to record sounds
On (default)
Off
Shot Lag
The time interval between each
trigger
(2)
30 seconds
(default)
2 seco
n
ds min.
60 minutes
max.
Sensitivity
Motion
Sensors
You can adjust the sensitivity of
the motion detection sensor.
Low
Middle
(default)
High
Target
Recording
Time
(3)
You can set the camera to record
between a certain period
On (to set the
period)
Off (default)
Time
Lapse
(4)
Set up time lapse mode and the
length of the lapse.
Normal
TL video
Off (default)
Language
To set different language
English
(defalut),
Deutsch,
Dansk,
Suomi,
Svenska,
Español,
Français,
Italiano,
Nederlands
,
Portugués,
简体中文,
繁體中文,
日本語
Time &
Date
To set time and date. You can
also choose the time format
(24h or 12h) and choose the
date format (dd/mm/yyyy,
yyyy/mm/dd or mm/dd/yyyy)
Set Time &
Date
Time Format
Date Format
Endless
Capture
If Endless Capture mode is on,
the camera won’t stop recording
when the memory card is full but
will delete the oldest videos or
photos to keep recording
continuously
On
Off (default)
Photo
Stamp
To choose if there will be time
and date on the photo.
Time & Date
(default)
Date
Off
Password
Protection
Set up password to secure your
camera
On
Off (default)
Beep Sound
Turn on or turn off the operation
sound
On (default)
Off
Format
Memory
Card
Decision with caution! You will
lose all of the data in the
memory card if you decide to
format it
Yes
No (default)
Serial NO
To set up the serial number of
the camera
(5)
On
Off (default)
Reset
Settings
Reset all the settings to the
original settings
Yes
No (default)
Version Version of the system
12895
(default)
(1) TL Video: Time lapse video. Camera will first of all, take photos between certain
period (set up in “Target Recording Time” and “Time Lapse”), then the camera will
generate a video with these photos. This function usually used to record flower bloom.
(2) For example, we set the 1 minute video length and 30 seconds shot lag. When the
camera detect an animal, it will start to record a 1-minute video. However, the camera
will not detect continuously. When the video is done, the camera will
not detect
immediately. It will detect again 30 seconds after the video in order to save the battery.
(3) In order to use the “Target Recording Time” function, please make sure that you
have already turn off the “Time Lapse” function and set up the length of the lapse
between each photo.
(4) If you turn on the “Time Lapse” and turn off the “Target Recording Time”, the
camera will take photos until the memory card is full.
(5) If you use several cameras at the same t
ime and you want to recognize which
camera took which photos and videos, set up a serial number could help you. The
serial number will show on the bottom right of the photos or videos.
Precaution
Do not dip the camera in the water.
The camera can work under 158°F but please keep the camera far enough from
fire to protect batteries.
Alkaline batteries are strongly recommended because alkaline batteries are able
to provide strong and stable power to the camera.
Please do not mix old batteries and new batteries.
If an DC 6V power adapter is used to supply the camera, please make sure
there are no batteries in the camera in order to prevent the overcharge.
As the Trail Camera doesn't have built-in memory,a Micro SD memory card must
be inserted into the camera before using.
1.1.Open the camera by unlocking two side locks.
1.2.Open the battery compartment.
1.3.Place 4 or 8 AA 1.5V type alkaline batteries into slots.NOTE:Must be
alkaline.If you have only 4 AA alkaline batteries,and make sure to place them all in
the upper or lower half of the battery compartment.
1.4.Insert Micro SD memory card.
Please note:
Ÿ TF high-speed card (Micro SD memory card) of Class 10 is required for this
camera.
Ÿ This camera is compatible for using Micro SD (TF) cards with a capacity up to
256GB.
Ÿ Please format your Micro SD (TF) card before the first use.
Ÿ Camera must be turned off before inserting or taking out the memory card.
Ÿ Do not take out Micro SD (TF) card or disconnect the camera from USB port
while formatting the card or transferring data to your computer,otherwise
recorded data and memory card may become damaged.
As soon as you have inserted the batteries and a Micro SD card,the camera is
ready for work! All you need to do is to choose a position for it and turn it on by
setting the operating mode switch to ON.
The camera has the following default settings:
Ÿ Mode:Photo
Ÿ Photo resolution:5MP
Ÿ Photo series:1 photo
Ÿ Video resolution:1280x720P
Ÿ Video length:10 seconds
Ÿ Audio recording:On
Ÿ Shot lag:30 seconds
Ÿ Motion sensor sensitivity:Middle
Ÿ Target recording time:Off
Ÿ Time lapse:Off
With the default settings,the camera will first take 1 photos when its motion sensor
detects a moving object.Please note that If you want sharper image quality,you can
turn up the resolution,however photo and video files created with these settings will
take more space on memory card.
2.Operating
For instance,4GB Micro SD (TF) card can store about 140 photos plus 70 videos (10
sec each) with the default settings.Therefore if you are using a small capacity Micro
SD (TF) card,or considering to set your camera for a longer period of time,you might
want to reduce photo and/or video resolution in the Settings.
2.1.Positioning the Camera
If you want to Install the camera on a tree, you could simply
use the Installation Belt：
1. Pass the Installation Belt through the support on the back of the camera. If the
Belt is too long for the tree which you choose, there are 3 holes on each side the
support, you could pass the Installation Belt through several holes to shorten the
belt;
NOTE:Setting the camera too close to tree branches can result in many “empty”
photos as the motion sensor will detect movements of tree branches and leaves.You
can also adjust the sensor sensitivity to the lower level to avoid irrelevant triggering.
2.2.Turning on the Camera
To turn on the camera,set the operating mode switch to ON.You will see a blinking
blue indicator on the front panel.After 15 seconds the camera will start to operate
independently and will go into standby mode.As soon as any object enters the
detecting range of the motion sensor,the camera will be activated and will start
capturing photos and/or videos (depending on the selected setup).
When the object moves out of the detecting range of the motion sensor,the camera
will go back into standby mode.
In the nighttime,infrared LEDs will provide the required light for capturing photos/vid-
eos.The effective range of the IR LEDs is 10- 65ft.Pictures and videos taken at night
are black and white.
In TEST mode you can work out the best exposure angle and range of the motion
sensor.First put the operating mode switch to TEST,then align the camera as follows:
Fasten the camera to a tree or any other suitable object using the included strap and
align the camera in the desired direction.Then move slowly from one side of the
target area to another.While doing this,watch the indicator located between IR LEDs.
If the red indicator lights up,you have been detected by the motion sensor.This way
you can find the best position for the camera.The detecting range of the sensor is
120°.
For an automatic review of the photos and videos stored on the memory card,press
MENU in REPLAY mode,and select “Activate Slide Show”.Each photo/video will be
displayed for about 2 seconds.To stop the slide show and keep the current image on
the screen,press the OK button.
3.4.Write Protection
This function can be used to protect individual files from accidental deletion.When in
REPLAY mode,press MENU and select “Write protect,” then choose “Write-protect
current file” to protect the selected photo/video.Select “Write-protect all files” to
protect all recordings from accidental deletion.Select “Unlock current file” to remove
write protection for the selected recording.
Select “Unlock all files” to remove write protection for all saved recordings.
You can use this function to delete photos/video recordings from the memory
card.Find the file you want to delete in REPLAY mode,then press MENU key,select
“Delete current file” and press OK to delete the selected recording.
3.2.Delete All Files
You can delete all recordings from the memory card by pressing MENU key when in
REPLAY mode,then select “Delete all files” and press OK.
3.3.Activate Slide Show
3.1.Delete Selected Files
NOTE:During the night,camera will use more energy for IR LEDs.Therefore,if the
battery is low (Less than 1/2),the camera will not take photos or shoot videos at
night,while in the daytime,the camera will work normally even with a low battery.
You can quickly preview recorded photos and videos on LCD screen.Open the
camera by unlocking two side locks and set the operating mode switch to the TEST
position.Press REPLAY key and Up/Down navigation keys to review the photos/vid-
eos.To play videos,press OK key to start playing and press OK again to stop.Press
REPLAY key to return back to standby.
3.Playback
2. My camera is not taking photos or recording videos!
Check if the TF card is Class 10;
Check if the TF card works normally on other devices;
Format the TF card.
3. The camera doesn’t detect anything!
Please make sure that the camera is not behind the glass;
Please check the setting in the menu to adjust the detection distance and the
detection sensibility of the camera then try again.
4. Why the camera doesn’t record during the night but it
works well during day time!
Please check the battery level of the camera. If the battery is low (1/3 of the full
battery), the night vision function will automatically shut down. Please change the
batteries then the night vision function will restore.
5. My “Target Recording
Time” function doesn’t work!
Please check if you have also turned on the “Time Lapse” function and have
chosen the time lapse mode then set up the lapse length.
QA
1. I can’t turn on my camera!
Please check if the batteries is full power;
Please check if battery polarity is correct;
Please re-install the batteries.
Warranty
In the spirit of "high quality,service,and development",with the concept of
"quality products,reasonable prices,and considerate service" and the
principle of responsibility and openness.We solemnly promises you:We
guarantees that the manufactured products are produced and inspected
in accordance with the relevant national standards.Substandard products
will never leave the factory.Guarantee strict performance and fulfillment of
product warranty,and strictly enjoy the relevant regulations of professional
service.To get extra 12-month warranty,total 24 months,please contact
official service team: Email:yizetai@outlook.com ,and provide informa-
tion(order number,product name).When the trail camera is replaced,the
warranty will still be the original trail camera you bought.You may return
the product after first obtaining a Return Material Authorization number
and following any other guidelines.
1.Lens
2.Infrared LEDs
3.PIR motion sensor
4.2.4”LCD screen
5.Menu button
6.Replay button
7.Navigation buttons
8.Shot button
9.OK button
10.TF card slot
11.USB slot
12.Operating mode switch
13.Fixation port
14.6V 1.5A Power supply port
15.Baterry slots
1
2
7
4
5
8
9
15
10 11 12
14
13
6
3
Key Function
MENU Press to open or close the menu
REPLAY Press to preview photos and videos
on 2.4”LCD screen
Up Navigation Up (in Menu mode); View
previous photo/video (in Playback
mode); Switch to Video (in Setup mode)
Down Navigation Down (in Menu mode); View
next photo/video (in Playback mode);
Switch to Photo (in Setup mode)
Left Navigation Left (in Menu mode)
Right Navigation Right (in Menu mode)
SHOT Press to take picture/record video
(in Setup mode)
OK Start/Stop playing video file (Playback
mode); Confirm/Enter (in Menu mode)
yizetai@outlook.com
1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16