Data Transfer Unit Model: V519 4G/3G Industrial Router 4G/3G Serial Server User Manual Model：V519 -1-
Data Transfer Unit 1．Interface Model: V519 Front 1) RJ45 Jack: LAN0 2) RJ45 Jack: LAN1 3) DC Jack: DC7V~35V wide voltage, DC12V is better and recommended. Description: LAN0 can be used as WAN under regular router mode; DC: 2.1mm Standard Round Interface, 7V~35V, Internal:+, Outside: - Back 1) 3G/4G/WIFI Antenna: SMA external rotation internal hole interface. 2) RESET: press for >5s when it’s powered on, SYS indicator will flash quickly and it’ll reboot.
Data Transfer Unit GND TX RX Model: V519 DC+ Currently UART1 can only be used as RS232, it’s GND/TX/RX/DC+ from left to right. But for data transmission, only GND/TX/RX will be used, respectively connecting them to the 5PIN, 2PIN, 3PIN of computer’s serial port to establish serial communication. DC+ works as input and output connector of power supply. (E.g.: when input is 12V, then the output voltage is 12V too.
Data Transfer Unit Model: V519 2.5 Access router from browser Start a browser like Chrome, Firefox, Edge etc. Enter http://192.168.8.1 in the address column Enter username and password (admin by default) and it’s shown as below: After login, you will be able to configure and manage this router.
Data Transfer Unit Model: V519 In this page, it’s easier to view the status of router. Click the registered courier and you will see the detailed information of 4G as below: 4. Interface In this page, it’s easier to view status of 4G LTE, LAN, Switch as below: 5. Network 5.1 LTE In this page, it allows users to configure LTE. By default, it’s LTE Gateway mode for V519, just inserting 4G/3G SIM card, later router will auto recognize and register to corresponding network of 4G/3G.
Data Transfer Unit Model: V519 select ISP. 5.2 Custom APN Please enter the APN information provided by ISP. The APN information of the domestic three ISPs for your reference as below: ISP 3G/4G APN Dial Number User Password cmnet *99# blank blank 3gnet *99# blank blank ctnet *99# card card ctnet #777 card card TD-SCDMA China Mobile TD-LTE, GSM China WCDMA Unicom FDD-LTE, GSM China FDD-LTE Telecom 4G China CDMA2000, Telecom EVDO 3G/2G 6. Application 6.
Data Transfer Unit Model: V519 6.2 LTE GPS LTE GPS is one of optional features because it uses the GPS built-in the 4G modules. If it’s required to enable GPS, please go to Network-->LTE-->GPS and enable GPS. If it positions successfully, you will see the map below. 6.2.1 GPS Data Upload It allows users to upload GPS data to the assigned server: 6.2.2 GPS Server Once enabled, GPS data will be broadcasted via the assigned port.
Data Transfer Unit Model: V519 corresponding port to get the GPS information. 6.3 Serial Port Only 1ch RS232 can be supported. RS485 can be customized if required. The serial port can also be worked as GPS positioning, terminal command line, ModBus, data transparent transmission. 7. System 7.1 Device In this page, it allows users to change operation mode and system language.
Data Transfer Unit Model: V519 7.1.1Operation Mode 5x operation modes can be selected: LTE Gateway (By Default), Gateway, 2.4G WISP, AP, Mix. Please see below photo: 1. LTE Gateway By default, it’s LTE Gateway mode, all you have to do is to insert 3G/4G SIM card, then the router will auto recognize and register to the corresponding network of 3G/4G. You can also custom and select your ISP. 2.
Data Transfer Unit Model: V519 then the router will reboot. Later please access the router from browser again, and go to Network->LAN->Select “Static IP” from dropdown list of Dial Mode ->Enter IP address, Subnet Mask, Gateway, DNS and other parameters you get from ISP->Click “Confirm” 3) PPPoE Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot.
Data Transfer Unit wireless connection Model: V519 5) Set and 6) Click “Interface” and you’ll see it’s all connected to 4G and WiFi: - 11 - enter related parameters:
Data Transfer Unit Model: V519 7.6 Manage Server In this page, it allows users to configure parameters of remote management server. After configuration, the router can be connected to the remote server, through remote server, it’s okay to configure the router. But for remote management server, the customized integration protocol will be required. Please contact your seller for more details.
FCC Caution. § 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. § 15.
