Smart multi-channel weather station with wireless sensor Model: C6082A / C3126A User Manual * *Smart phone not included
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
TABLE OF CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSOLE. . . . . . . . .
-- Do not subject the unit to excessive force, shock, dust, temperature or humidity. -- Do not cover the ventilation holes with any items such as newspapers, curtains etc. -- Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth. -- Do not clean the unit with abrasive or corrosive materials. -- Do not tamper with the unit’s internal components. This invalidates the warranty.
OVERVIEW CONSOLE 1 6 11 7 12 13 14 2 8 3 4 5 15 9 10 16 1. 2. 3. 4. 5. 6. [ ALARM/SNOOZE ] key LCD display [ CHANNEL / + ] key [ MODE / ALARM ] key [ MAX / MIN / - ] key [ HI / LO ] slide switch 7. [ / CAL ] key 8. [ TIME SET ] key 9. Table stand 10. Battery door 11. Wall mounting hole 12. [ °C / °F ] key LCD DISPLAY 1. Time & Date 2. Temperature & humidity 3. Indoor temperature & humidity 1 2 3 5 13. [ Refresh ] key 14. [ RESET ] key 15. [ SENSOR / WI-FI ] key 16.
WIRELESS THERMO-HYGRO SENSOR 1. LED indicator 2. Wall mounting holder 3. Channel slide switch 1 4. [ RESET ] key 5. Battery compartment 2 3 4 5 INSTALLATION AND SETUP INSTALL WIRELESS THERMO-HYGRO SENSOR 1. Remove the battery door of the sensor. 2. Use the channel slide switch to set the channel number for the sensor (e.g. Channel 1) 3. Insert 2 x AA size batteries into the battery compartment according to the polarity marked on the battery compartment, and close the battery door. 4.
SETUP THE CONSOLE INSTALL THE BACKUP BATTERY Backup battery provides power to the console to retain clock time and date, max/min records and calibration value. Step 1 Step 2 Step 3 Remove the console battery door with coin Insert a new CR2032 button cell battery Replace the battery door. NOTE: -- The backup battery can back up: Time & Date, Max/Min records and calibration value. -- The built-in memory can back up: Router setting server settings.
ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL) The console can support up to 7 wireless sensors. 1. In the new wireless sensor, slide the Channel switch to a new CH number 2. Press the [ RESET ] key on the new sensor. 3. At the back of the console, press the [ SENSOR / WI-FI ] key enter sensor synchronization mode 4. Wait for the new sensor(s) to pair up with the console. (about 1 minute) 5. Once the new sensor(s) are connected to the console successfully, their temperature and humidity will be shown accordingly.
Step 1: At the home screen , tap the on the top right corner to add your console. Step 2: On "Add Manually" screen, choose "Sensors" in the left menu bar and then select "Temperature and Humidity Sensor(Wi-Fi)". Step 3: Make sure you select the 2.4G network and enter your Wi-Fi password then tap the "Next". Step 6: Once it success, the console icon will shown, and you can customize its information. Step 5: There will auto scan and register your device.
3. The console will automatically exit AP mode and return to normal operation once it's connected to Wi-Fi router. NOTE : - Smart weather station can only connect to 2.4G WI-FI network - Enable the location information in your mobile when you add your console to App. - User may press and hold [ SENSOR / WI-FI ] for 6 seconds to exit AP mode any time.
TO SET ALERT NOTIFICATION You can set the temperature and humidity high / low alarm. Step 1: Tap the "Setting" on the bottom of the "device Screen". Step 2: Tap the "Temperature Alarm" or "Humidity Alarm". Step 3: Tap the "INDOOR" or "CH 1 ~ 7 ". Step 4: Set the High / Low trigger values and slide the switch to activate the alert.
IOT APPLICATIONS Through the Smart life App, you can create the temperature and humidity trigger conditions to control other Smart Life compatible device(s) automatically. Step 1: Tap the " Smart" icon on Home screen, and follow the instruction to set condition and task.. Step 2: Tap the " Step 3: Tap one of below tag to set different trigger condition. " icon. NOTE : - Any tasks required or performed by third party devices are at user's own choice and risk.
FIRMWARE UPDATE The console can be updated through your WI-FI network. If new firmware is available, a notification or pop up message will be shown on your mobile when you open the App. Follow the instruction in the App to do the update. During the update process, the console will show the progress status percentage at the bottom of the screen. Once the update complete, the console screen will reset and back to normal mode.
ACTIVATING ALARM FUNCTION 1. In normal mode, press [ MODE / ALARM ] key to show the alarm time for 5 seconds. 2. When the alarm time displays, press [ MODE / ALARM ] key again to activate the alarm function. Alarm off Alarm on When clock reach the alarm time, alarm sound will start. Where it can be stopped by following operation: -- Auto-stop after 2 minutes alarming if without any operation and the alarm will activate again in the next day.
TREND INDICATOR The trend indicator shows the temperature or humidity trends of changes based on later 15 minutes. MAX / MIN DATA RECORD The console can record MAX / MIN readings both daily and since last reset. Daily MAX reading Daily MIN reading Rising Steady Falling MAX reading MIN reading since last since last reset reset TO VIEW MAX / MIN 1. In normal mode, press [ MAX / MIN ] key on the front side, to check the daily MAX records of current channel and indoor. 2.
SET LCD DISPLAY CONTRAST In normal mode, press [ / CAL ] key to adjust LCD contrast for best viewing on table stand or wall mounted. MAINTENANCE BATTERY REPLACEMENT When low battery indicator “ ” is displayed in CH section of the LCD display, it indicates that the current channel sensor battery power give wireless sensor shown is low respectively. Please replace with new batteries.
In Humidity Humidity unit % 1 ~ 20% RH ± 6.5% RH @ 25°C (77°F) Accuracy 21 ~ 80% RH ± 3.5% RH @ 25°C (77°F) 81 ~ 99% RH ± 6.5% RH @ 25°C (77°F) Resolution 1% WI-FI Communication Specification Standard 802.11 b/g/n Operating frequency : 2.