rS-350-eDPb Deluxe Keyless entry & remote Start June 25, 2013 Operation guide Temporary cover. Color cover is in a separate file.
Transmitter Overview THe TranSmiTTer 1 Part number: 147-03 Call your dealer or visit www.caralarm.com to order replacement transmitters.
Transmitter Functions (cont’d) TrunK releaSe / CHannel 2: Press the “TRUNK” button for 3 seconds� • THE SYSTEM WILL UNLOCK AND THE TRUNK WILL OPEN (IF EQUIPPED)� remOTe STarT: Press and release the “START” button twice within 5 seconds� (see user feature #17 for additional options) x2 • THE PARKING LIGHTS WILL FLASH ONCE AND THE STATUS LIGHT WILL FLASH RAPID GREEN� • THE SYSTEM WILL TURN ON THE IGNITIONS AND PROCEED TO START THE ENGINE� • ONCE THE ENGINE IS RUNNING, THE PARKING LIGHTS WILL TURN ON AND ST
Transmitter Functions (cont’d) CHannel 4: Press and hold the “LOCK” & “TRUNK” buttons for 3 seconds� • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4 OUTPUT� CHannel 5: Press and hold the “UNLOCK” & “START“ buttons for 3 seconds� • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5 OUTPUT� PaniC: Press and hold the “LOCK” or “UNLOCK” button for 3 seconds� • THE SIREN/HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED� OR SilenT lOCK / unlOCK: Press and rele
Transmitter Functions (cont’d) lOW vOlTage/TemP auTO STarT: Press and release the “START” button within 5 seconds of locking the system� 1 2 • THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE THE LOW VOLT/LOW TEMP(15 DEGREE ONLY) AUTOSTART IS ACTIVATED� SEE BELOW FOR MORE INFO� auXiliary FunCTiOnS 1-4: The actual operation of these functions will vary from car to car� They are designed to operate extra functions like automatic sliding doors or motorized hatches� Aux 1-4 are virtual outputs only available when
Other Remote Start Features (cont’d) Turbo Timer Feature This is recommended for vehicles equipped with a turbocharger. It allows the engine to idle after driving to cool the turbo. When this Installer Programmable Feature (#4) is enabled, the system will automatically keep the engine running as follows: • With the engine running, hold the brake pedal and engage the parking brake.
Using The Valet Switch Emergency Override If your controller becomes inoperable, you’d need to perform an emergency override to disarm the starter interrupt. To do so, use the following steps: STEP 1 - Enter the vehicle STEP 2 - Turn the ignition key to the “ON” position STEP 3 - Press the valet switch (located in the window-mount antenna) once NOTE: Enter your SecureCode at this time if programmed via user feature #1 STEP 4 - Turn the ignition “OFF”.
The Status Light The status lights, located in the antenna, provide a visual indication of the system’s status via GREEN (remote start status) and RED (system status) lights. SYSTEM STATUS (RED LIGHT): ON CONSTANT: The system is in valet mode. FLASHING FAST: One of the automatic locking features is in progress. AUTOMATIC TRANSMITTER VERIFICATION (RED LIGHT): Every time you turn on the ignition key, the status light will flash a number of times equal to the number of transmitters programmed to the system.
Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both). All are programmable, and must be turned on to operate. Once activated, the user has 53 seconds to cancel the Anti-Carjacking protection process (described below). If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition.
Programming Transmitters Standard Programming: This method to program additional or replacement transmitters does not affect the Unauthorized Transmitter Alert (UTA) feature. Before you begin, have all transmitters which are to operate the system at hand. Step 1 Then, turn the ignition “on”. Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times. The siren/horn will briefly sound, confirming that the system is ready to learn a transmitter code.
Programming Features Step 1 Turn the ignition key “ON”, then “OFF” Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user features (10 times to access installer features). ~ The siren/horn will sound and the status light will turn on. Step 3 Within 10 seconds of step 2, press the valet switch the number of times corresponding with the desired feature’s number. ~ The siren/horn will chirp, the status lights, and the parking lights will flash equal to the selected feature.
User Programmable Features (cont’d) Feature #3 - Automatic Rearming Off (press “lock” button to program) - DEFAULT On w/o doors locking (press “unlock” button to program) On w/ doors locking (press “trunk” button to program) Enhanced auto rearm (press “start” button to program) “Automatic Rearming”, described on page 7, rearms the starter interrupt if accidentally unlocked/disarmed. Options are to have Automatic Rearming operate with or without also locking the doors when the system does rearm.
User Programmable Features (cont’d) Feature #9 - Confirmation Chirp Volume Medium High (press “trunk” button to program) - DEFAULT Low (softest) (press “lock” button to program) Medium Low (press “unlock” button to program) High (loudest) (press “start” button to program) This feature allows the choice of four different volume levels of the system’s confirmation chirps, and when programming it, the buttons can be repeatedly and sequentially pressed, thus making it easy to hear and choose the setting
User Programmable Features (cont’d) Feature #17 - Remote Start Activation Press “start” button 2 times (press “lock” button to program) - DEFAULT Press “start” button 1 time (press “unlock” button to program) Press Lock & Unlock (press “trunk” button to program) This feature changes how the remote start feature is activated using the controller or transmitter.
Installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming. These features have a direct affect upon the system’s operations related to the installation and vehicle type AND SHOULD ONLY BE CHANGED BY THE INSTALLER!!! Feature #1 - Doorlocking Functions 0.
Installer Programmable Features (cont’d) Feature #6 - Engine Detection Method (press “lock” button to program) - DEFAULT Tachless Hi Tachless Lo (press “unlock” button to program) Tach Wire (press “trunk” button to program) Data Tach (press “start” button to program) Crank Only (press “lock” & “unlock” to program) This feature selects the method in which the remote start monitors the engine’s running condition in remote start mode.
Installer Programmable Features (cont’d) Feature #10 Gasoline Or Diesel Engine Gasoline (press “lock” button to program) - DEFAULT Diesel 15 Sec. Delay (press “unlock” button to program) Diesel 20 Sec. Delay (press “trunk” button to program) Diesel 30 Sec. Delay (press “start” button to program) This feature changes the system’s timing of the ignition and starter output sequence for gas or diesel engines. Gasoline: the starter output will occur 3 seconds after the ignitions turn on.
Programmable Features Matrix User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button 1 Secure Code 1, 0 (default) 2 Last Door Arming 3 Automatic Rearming ”START” button Unlock button Trunk button Off On w/o lock On w/ Lock Off On w/o lock On w/ Lock Enhanced Rearm 4 Starter Interrupt Functions W/ Lock Anti-Grind Only Lock+Anti-Grind Automatic 5 Ignition Override On Off 6 Ignition Lock/Unlock Off Lock w/ IGN ON Unlock w/ IGN Off Lock + Unlock w/ IGN On