Technical Manual

ManualsBrandsEWT ManualsElectronicsRFID READER MODULE

East Wind Technologies, Inc.

EWTJ680F-K-01 Module

General Technical Manual

(Revision 1.00)

East Wind Technologies, Inc.

June 13, 2022

Summary of content (70 pages)

PAGE 1
East Wind Technologies, Inc. EWTJ680F-K-01 Module General Technical Manual (Revision 1.00) East Wind Technologies, Inc.
PAGE 3
East Wind Technologies, Inc. 1 Introduction 1.1 Features ￭ NFC Function ￭支援 ISO 14443A, ISO 15693, FeliCa Lite-S (RCS966) ￭支援 ISO-DEP(ISO 14443-4) ￭頻率：13.56 MHz (±20PPM) ￭輸入電壓：5V – 12V (±0.5V) ￭平均電流：110mA (±10mA) ￭感應距離：5.5cm (±0.5cm, ISO 14443A 卡 (MF1 IC S50) ) ￭介面：RS-232 ￭天線、讀卡機分離￭主板尺寸：35mm x 51mm ￭ RF cable 最大長度可達：60cm ￭含金屬罩￭儲存溫度：-40℃~95℃ ￭操作溫度：-40℃~85℃ ￭操作濕度：90% 無凝固￭含 LED 燈￭ Baud Rate: 19,200bps ￭ RF connector：I-PEX, U.
PAGE 4
East Wind Technologies, Inc. Warning: Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 5
East Wind Technologies, Inc. FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only.
PAGE 6
East Wind Technologies, Inc. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host Copyright © 2022 East Wind Technologies, Inc. All rights reserved.
PAGE 7
East Wind Technologies, Inc. will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
PAGE 11
East Wind Technologies, Inc. 1.3 Pin Configurations Pin Function Type Description 1 GND Power GND 2 VCC Power VCC 3 RESET-IO Input Initial low(0V - 0.9V), pull-high(2.4V – 3.3V) to reset hardware 4 ICC Output Card in/out indicate 0: card in; 1: card out 5 TXD/SDA Input/Output RS232C TXD / UART TXD / IIC SDA 6 RXD/SCL Input RS232C RXD / UART RXD / IIC SCL 仰視圖(Bottom View) K Copyright © 2022 East Wind Technologies, Inc. All rights reserved.
PAGE 15
East Wind Technologies, Inc. 1.5 Basic Mode EWTJ680F-K is a slave device; the "ask & answer" is the basic working mode. That means EWTJ680F-K received a command from master machine, and then to execute the command and answer to master machine. This is a command cycle. A new command will not be accepted while the module is executing a command. So when you develop the application program, you MUST be sure the last command cycle is finished, then to send the next command. 1.
PAGE 16
East Wind Technologies, Inc.  1.7.2 Checksum: 1 byte, Exclusive OR (XOR) results from length byte to the last byte of data. Data returned format   Success: Length Command Data Failure: Length Invert Command Checksum Checksum NOTE: "Failure" means that the communication between module and card failed. 1.8 Data Returned Time Slaves begin to execute the command once received host's commands. The executive time is normally less than 100ms, depand on the command type.
PAGE 17
East Wind Technologies, Inc. 2 Communication Interface 2.1 RS232C interface 2.1.1 Physical Interface RS232C is the UART interface which belongs to RS232C-level. The communication between RS232C and PC is via TXD, RXD and GND pins. The host TXD pin connects to the device RXD pin, meanwhile the host RXD pin connects to the device TXD pin. The communication protocol is byte oriented. Both sending and receiving bytes are in hexadecimal format.
PAGE 18
East Wind Technologies, Inc. 3 Application-layer Protocol 3.1 Overview This chapter will introduce the communication protocol application level commands and data structures in detail, the application level protocol only introduce the commands and the data. We illustrate each command in the following format: Frame Command Data Checksum Frame Header: 1 byte length information, all the bytes except Checksum byte. Checksum: Exclusive OR (XOR) results from length byte to the last byte of data.
PAGE 19
East Wind Technologies, Inc. 3.2 System commands 3.2.1 Module reset to factory default Function: Reset all configuration of the module to factory default setting. The new setting will effect after re-power on. Host send: Frame 0x0F 52 45 53 45 54 Checksum Success: Frame 0x0F Checksum Frame 0xF0 Checksum Failure: send: 0x07 0F 52 45 53 45 54 5D return: 0x02 0F 0D 3.2.2 Set LED Function: set the LED ON or OFF.
PAGE 20
East Wind Technologies, Inc. Success: Frame 0x1B Checksum Frame 0xE4 Checksum Failure: 3.2.4 Set Automatic Detecting Card Interval Time Function: set interval time of automatic detecting card function. The default is 100ms. Settings will save in the module; it will be not lost after power OFF. Host sends: Frame 0x1C Time Checksum Time: 1 byte, 0x00 to 0xFF, unit is 10mS, 0x01 means 10mS. Success: Frame 0x1C Checksum Frame 0xE3 Checksum Failure: 3.2.
PAGE 22
East Wind Technologies, Inc. 3.3 ISO14443A/B CPU Card Commmands 3.3.1 ISO14443 TYPE A Request Function: ISO14443A request cards, cards include MIFARE and other ISO14443A cards. In the returned results, user could judge the length of serial number via the returned data package length, and judge the card type by ATQA, also judge whether the card supports ISO14443-4 by SAK. If automatic detect card function was opened, then this command is only to read the result of automatic detect card.
PAGE 23
East Wind Technologies, Inc. Success: Frame 0x60 Info. Checksum Info: total 13 bytes, 12 bytes of ATQB: 0x50 (1 byte), PUPI (4 bytes), application data (4 bytes), protocol information (3 bytes), 1 byte answer to Attribute. For more details, please reference to ISO14443-3 "ATQB Response" part. Failure: Frame 3.3.4 0x9F Checksum Request Card according to EMV and PBOC Function: Card Request according to EMV and PBOC standards and to set the communication parameters between the module and card.
PAGE 24
East Wind Technologies, Inc. Failure: Frame 3.3.6 0xCE Checksum ISO14443-4 TYPE B Card Halt Function: To let the current ISO14443B card enters into halt status. Not all of the cards support this command, most don't support, especially the new card. Host sends: Frame 0x62 PUPI Checksum PUPI: 4 bytes, PUPI of the card that will be halt. Success: Frame 0x62 Checksum Frame 0x9D Checksum Failure: Copyright © 2022 East Wind Technologies, Inc. All rights reserved.
PAGE 25
East Wind Technologies, Inc. 3.4 MIFARE 1K/4K/mini Card Commands 3.4.1 MIFARE Request MIFARE series cards request, please refer to ISO14443 TYPE A Request. 3.4.2 MIFARE 1K/4K Data Block Read Function: Read MIFARE 1K/4K one block data.
PAGE 26
East Wind Technologies, Inc. Data: Failure: Frame 0x2A Data blocks * 16 bytes card data per block Frame 3.4.4 0xD5 Checksum Checksum MIFARE 1K/4K Data Block Write Function: Write the data to a block of MIFARE 1K/4K. Host sends: Frame 0x22 Key ID Block Key Data Checksum Key ID: 1 byte, Key identifier; Block: 1 byte, Block number to be written; Key: 6 bytes, the key of the card; Data: 16 bytes data to be written. Success: Frame 0x22 Checksum Frame 0xDD Checksum Failure: 3.4.
PAGE 27
East Wind Technologies, Inc. MIFARE 1K/4K’s default. The card's key block and block 0 could not be used as a purse. For more details about MIFARE 1K/4K card, please reference the datasheet. Host sends: Frame 0x23 Key ID Block Key Value Checksum Key ID: 1 byte, Key identifier; Block: 1 byte, Block number to be initialized; Key: 6 bytes, the key of the card; Value: 4 bytes, initialized value, LSB first. Success: Frame 0x23 Checksum Frame 0xDC Checksum Failure: 3.4.
PAGE 28
East Wind Technologies, Inc. Frame 0x25 Checksum Frame 0xDA Checksum Failure: 3.4.9 MIFARE 1K/4K Purse Decrement Function: Purse decrement of MIFARE 1K/4K. The format of the purse uses MIFARE 1K/4K’s default. Purse decrement means the decrement on the basis of the original number. Purse decrement only needs the “read authority” of the key.
PAGE 29
East Wind Technologies, Inc. Host sends: Frame 0x28 Checksum Frame 0x28 Checksum Frame 0xD7 Checksum Success: Failure: 3.4.12 Download MIFARE 1K/4K Card Key into Module Function: Download the MIFARE 1K/4K card key into module. There are 32 key memory spaces in the module that could storage 32 different keys. While using the downloaded key in the module, this key wouldn’t appear on the pin-outs of the PCD. So it could be more safety.
PAGE 30
East Wind Technologies, Inc. 3.4.13 About KEY Identifier There is a byte of KEY identifier in command of MIFARE 1K/4K cards. This byte will identify the way to get the card key. KeyIdentifier BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 BIT0 = 0: KEY A; authenticate Key A of the card. BIT0 = 1: KEY B; authenticate Key B of the card. BIT1 = 0: Using the following 6 bytes Key in command. BIT1 = 1: Using the downloaded Key by command.
PAGE 31
East Wind Technologies, Inc. 3.5 MIFARE Ultralight/Ultralight C/Ultralight EV1 Card Commands 3.5.1 MIFARE Ultralight/Ultralight C/Ultralight EV1 Request For MIFARE UltraLight/UltraLight C card request, please refer to ISO14443 TYPE A Request. 3.5.2 MIFARE Ultralight/Ultralight C/Ultralight EV1 Card Read Function: Read the data from MIFARE UltraLight/UltraLight C cards. A read command will read 4 blocks data from the card.
PAGE 32
East Wind Technologies, Inc. of authentification is controled by the module. Host sends: Frame 0x43 Key Checksum Key: 16 bytes UltraLight C key Success: Frame 0x43 Checksum Frame 0xBC Checksum Failure: 3.5.5 MIFARE UltraLight C Ek (RndB) Read Function: To read encrypted RndB this is generated by Ultralight C card. Command 0x44 and 0x45 are the separation commands to authenticate Ultralight C.
PAGE 33
East Wind Technologies, Inc. CBC, then to compare result with RndA. 3.5.7 If equality, authentication is passed. Ultralight EV1 GET_VERSION Function: The GET_VERSION command is used to retrieve information on the MIFARE family, product version, storage size and other product data required to identify the Ultralight EV1 card. Host sends: Frame 0x46 Checksum Frame 0x46 Version Success: Checksum Version: 8bytes Ultralight EV1 Card version. Failure: Frame 0xB9 Checksum As follows: 3.5.
PAGE 34
East Wind Technologies, Inc. Data: 3 bytes Ultralight EV1 counter data. Failure: Frame 3.5.10 0xB7 Checksum Ultralight EV1 INCR_CNT Function: The INCR_CNT command is used to increment one of the 3 one-way counters of the Ultralight EV1. The two arguments are the counter number and the increment value. Host sends: Frame 0x49 Address Data Checksum Address: 1byte, Ultralight EV1 counters address. Data: 3 bytes, Ultralight EV1 INCR_CNT data.
PAGE 35
East Wind Technologies, Inc. Failure: Frame 3.5.13 0xB4 Checksum Ultralight EV1 CHECK_TEARING_EVENT Function: The CHECK_TEARING_EVENT command enables the application to identify if a tearing event happened on a specified counter element. It takes the counter number as single argument and returns a specified valid flag for this counter. If the returned valid flag is not equal to the predefined value, a tearing event happened.
PAGE 36
East Wind Technologies, Inc. 3.6 MIFARE Plus Card Commands EWTJ680F-K reader module support MIFARE Plus card operation. NXP MIFARE Plus cards are used to instead MIFARE 1 card. We provide application commands are based on Level 3. In the card level 3, the authentication use AES encryption algorithm. In the communication process between module and card, all are using encrypted data + command with MAC + response with MAC mode. So the security of RF communication is extremely high.
PAGE 37
East Wind Technologies, Inc. using this command, please use MIFARE Plus Write Perso command to write all AES key and the initial value of all the blocks, then make the changed data effect. Host sends: Frame 0x34 Checksum Success: Frame 0x34 Status Checksum Status: status code returned from the card. Please reference: MIFARE Plus Returned Status Code. Failure: Frame 3.6.2.
PAGE 38
East Wind Technologies, Inc. 3.6.3.2 MIFARE Plus Data Block Read Function: Level 3 command, reading operation of data block; before reading, the relevant block need to be authorized. Host sends: Frame Start Block: Blocks: Success: 0x37 Start Block Blocks Checksum Data Checksum 2 bytes (MSB first). 1 byte, blocks to be read Frame 0x37 Status Status: status code returned from the card. Please reference: MIFARE Plus Returned Status Code. Data: block * 16 bytes Failure: Frame 3.6.3.
PAGE 39
East Wind Technologies, Inc. 3.6.3.5 MIFARE Plus Purse Read Function: Level 3 command, reading the balance of the purse. Host sends: Frame 0x3A Block Checksum Block: 2 bytes (MSB first), block number. Success: Frame 0x3A Status Value Checksum Status: status code returned from the card. Please reference: MIFARE Plus Returned Status Code. Value: 4 bytes balance of the purse. Failure: Frame 3.6.3.
PAGE 40
East Wind Technologies, Inc. sector. Host sends: Frame 0x3D Source Target Checksum Source: 2 bytes (MSB first), source block number Target: 2 bytes (MSB first), target block number Success: Frame 0x3D Status Checksum Status: status code returned from the card. Please reference: MIFARE Plus Returned Status Code. Failure: Frame 3.6.3.9 0xC2 Checksum MIFARE Plus First Authenticate Function: Level 1/3 Command.
PAGE 41
East Wind Technologies, Inc. 3.6.4 MIFARE Plus Returned Status Code There is a status code after MIFARE Plus card response; this table indicates the possible value. HEX Status Explanation 0x90 OPERATION_SUCCESS Normal operation ends 0x06 AUTHENTICATION_ERROR Authentication conditions are not met; No exist block; The block is visited in a numeric 0x07 COMMAND_OVERFLOW Plaintext R&W in a task Overflow. 0x08 INVALID_MAC MAC error.
PAGE 42
East Wind Technologies, Inc. 3.7 DESFire Card Commands We are here to provide a separate operation for DESFire card. DESFire card authentication and communication use DES encryption algorithm. The encryption of communication between EWTJ680F-K and DESFire cards is set by users. If the user sets the RF communication process is encrypted then the card data security is extremely high. Use the following command allows the user to quickly start DESFire card R&D works.
PAGE 43
East Wind Technologies, Inc. Failure: Frame 3.7.1.5 0x6F Checksum DESFire Authenticate first step Get ekNo (RndB) Function: Authentication is initiated by the module. Get the ekNo (RndB) from the card. Host sends: Frame 0x8E KeyNo Checksum KeyNo: 1 byte. Success: Frame 0x8E Status ekNo (RndB) Checksum Status: status code returned from the card. Please reference: DESFire Returned State Code. If the status code is 0xAF, it's correct.
PAGE 44
East Wind Technologies, Inc. 3.7.1.7 DESFire Select Application Function: Select the specified card application. The following operation will effect to this application. Host sends: Frame 0x98 AID Checksum Status Checksum AID: 3 bytes (LSB in first). Success: Frame 0x98 Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 3.7.2 0x67 Checksum DESFire Initialization Commands 3.7.2.
PAGE 45
East Wind Technologies, Inc. 3.7.2.3 DESFire Change Key Settings Function: Modify the master key/application master key configuration setting. DES/3DES encryption and CRC checksum will be used in the process of instruction execution. Host sends: Frame 0x91 KeySettings Checksum KeySettings: 8 bytes encrypted key settings. Success: Frame 0x91 Status Checksum Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 3.7.2.
PAGE 46
East Wind Technologies, Inc. 3.7.2.6 DESFire Get Key Version Function: Get the key version information. Host sends: Frame KeyID: 1 byte. Success: Frame 0x94 KeyID 0x94 Checksum Status Version Checksum Status: status code returned from the card. Please reference: DESFire Returned State Code. Version: 1 byte. Failure: Frame 0x6B Checksum 3.7.2.7 DESFire Delete Application Function: Delete the specified application.
PAGE 47
East Wind Technologies, Inc. Success: Frame 0x97 Status AID Checksum Status: status code returned from the card. Please reference: DESFire Returned State Code. AID: Application identifier length is 3 bytes, the length is 3* identification number. Failure: Frame 0x68 Checksum 3.7.2.10 DESFire Get File IDs Function: Get all file identifier of current application. Host sends: Frame 0x9B Checksum Frame 0x9B Status Success: FID Checksum Status: status code returned from the card.
PAGE 48
East Wind Technologies, Inc. Host sends: Plaintext: Frame 0x9D File ID Comm.Sett AccessRight 0x9D File ID EncryptedSetting Checksum Cryptograph: Frame Checksum File ID: 1 byte. Comm.Sett: 1byte, 0: Plaintext; 1: MAC code checksum; 3: DES/3DES encryption. AccessRight: 2 bytes (LSB in first). EncryptedSetting: 8 bytes, 1 byte communication setting + 2 bytes file permission + 2 bytes CRC + 3 bytes 0x00 got via encryption.
PAGE 49
East Wind Technologies, Inc. Frame 0x9F Status Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 0x60 Checksum Checksum 3.7.2.15 DESFire Create Value File Function: Create Value File in current application, support backup mechanism. Host sends: Frame 0xA0 FID Comm. Sett Access Right Lower limit Upper limit Value Limited Credit enable Checks um FID: 1 byte. Comm.Sett: 1byte, 0: Plaintext; 1: MAC code checksum; 3: DES/3DES encryption.
PAGE 50
East Wind Technologies, Inc. 3.7.2.17 DESFire Create Cyclic Record File Function: Create Cyclic Record File in the current application. Host sends: Frame 0xA2 Comm. Sett FID Access Right Record Size Max Records Checksum FID: 1 byte. Comm.Sett: 1byte, 0: Plaintext; 1: MAC code checksum; 3: DES/3DES encryption. AccessRight: 2 bytes (LSB in first). Record Size: 3 bytes (LSB in first), bytes of single record. Max Records: 3 bytes (LSB in first), total record numbers of the file.
PAGE 51
East Wind Technologies, Inc. Status: status code returned from the card. Please reference: DESFire Returned State Code. Data: data returned from the card. Failure: Frame 0x5B Checksum 3.7.3.2 DESFire Write Data Function: Write specified Data File (Standard Data File or Backup Fata File) in current application. For Backup Data File, Commit is needed to take effect after write, refer to: DESFire Commit Transaction please. Host sends: Frame 0xA5 FID Offset Length FID: 1 byte.
PAGE 52
East Wind Technologies, Inc. Host sends: Frame 0xA7 FID Data Checksum FID: 1 byte. Data: There are two lengths, depending on whether encryption. Plaintext: 4 bytes value (LSB in first). Encryption: 8 bytes encrypted data, After decryption: 4 bytes value (LSB first) + 2 bytes CRC + 2 bytes 0x00. Success: Frame 0xA7 Status Checksum Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 3.7.3.
PAGE 53
East Wind Technologies, Inc. Frame 0xA9 Status Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 3.7.3.7 0x56 Checksum Checksum DESFire Write Record Function: Write data to specified Data File in current application. The data file could be Linear Record or Cyclic Record file. This command appends one record at the end of the record file. The status will show an error when the linear record file is full.
PAGE 54
East Wind Technologies, Inc. 3.7.3.9 DESFire Clear Record File Function: Clear specified Record File of current application. Commitment is needed to take effect after this operation, refer to: DESFire Commit Transaction please. Host sends: Frame 0xAC FID Checksum 0xAC Status Checksum FID: 1 byte. Success: Frame Status: status code returned from the card. Please reference: DESFire Returned State Code. Failure: Frame 0x53 Checksum 3.7.3.
PAGE 55
East Wind Technologies, Inc. 3.7.
PAGE 56
East Wind Technologies, Inc. 3.8 SR176 Card Commands 3.8.1 SR Serial Cards 1 Slot Initiate Card Function: SR serial cards (SR176/SRI512/SRI1K/SRI2K/SRI4K/SRIX4K, the same below) single channel initiate card. Before read/write card, it needs to use the command of “SR serial cards select” to select the card. More detailed card operations please refer to the card manual please. Host sends: Frame 0x63 Checksum Success: Frame 0x63 Card ID Checksum Card ID: 1 byte. It is a random ID. Failure: Frame 3.8.
PAGE 57
East Wind Technologies, Inc. 3.8.4 SR176 Card Read Function: Read data block of SR176 card. Host sends: Frame StartBlock: BlockNumbers: Success: Frame 0x68 StartBlock BlockNumbers Checksum 1 byte. 1 byte; the quantity of blocks to be read. 0x68 Data Checksum Data: 2 bytes * BlockNumbers, data from the card. Failure: Frame 3.8.5 0x97 Checksum SR176 Card Write Function: Write into the data block of SR176 card. After wrote, module will read the data to compare. If not equal, then return failure.
PAGE 58
East Wind Technologies, Inc. 3.9 SRI512/1K/2K/4K Card Commands 3.9.1 SRI Serial Cards 1 Slot Initiate Card Please reference: SR serial cards 1 slot initiate card. 3.9.2 SRI Serial Cards 16 Slots Initiate Card Function: SR serial cards (SRI512/SRI1K/SRI2K/SRI4K/SRIX4K, the same below) 16 channels initiate card.
PAGE 59
East Wind Technologies, Inc. 3.9.6 SRI Serial Cards Read Function: Read data block of SRI serial card. Host sends: Frame StartBlock: BlockNumbers: Success: Frame 0x6B StartBlock BlockNumbers Checksum 1 byte. 1 byte; the quantity of blocks to be read. 0x6B Data Checksum Data: 4 bytes * BlockNumbers, data from the card. Failure: Frame 3.9.7 0x94 Checksum SRI Serial Cards Write Function: Write data block of SRI serial card. After write, module will read the data to compare.
PAGE 60
East Wind Technologies, Inc. 3.9.9 SRI Serial Cards Read UID Function: Read UID of SRI serial card. Host sends: Frame 0x6E Checksum Success: UID: Frame 0x6E UID 8 bytes, UID of CURRENT CARD. Checksum Failure: Frame 3.9.10 0x91 Checksum SRIX Serial Cards Authentication Function: SRIX serial card authentication; Anti clone function of the SRIX serial card. Host sends: Frame 0x6F Data: 6 bytes, data input. Success: Frame 0x6F Data Checksum Result Checksum Result: 3 bytes, result return.
PAGE 61
East Wind Technologies, Inc. 3.10 ISO15693 Operation Commands 3.10.1 ISO15693 Inventory Function: Find a card in RF effective field. If success, to set the tag as CURRENT TAG. If automatic detecting card function was turned on, then this command is to take the result of automatic detecting card, not to detect card after received the command. Host sends: Frame 0x5C AFI Checksum AFI: 1byte AFI, detect card equal to AFI only.
PAGE 62
East Wind Technologies, Inc. refers to the data sheet of the card. Failure: Frame 0xA1 3.10.4 Checksum ISO15693 Reset to Ready Function: Set a stay quiet TAG reset to ready. Host sends: Frame 0x5F UID Checksum Data: 8 bytes, UID of the tag to reset to ready. Success: Frame 0x5F Checksum Frame 0xA0 Checksum Failure: 3.10.5 ISO15693 Read Blocks Function: Read data blocks of CURRENT TAG.
PAGE 63
East Wind Technologies, Inc. 3.10.7 ISO15693 Lock Block Function: Lock a block of CURRENT TAG. Host sends: Frame 0x56 BlockNumber Checksum BlockNumber:1 byte, block number to be locked. Success: Frame 0x56 Checksum Frame 0xA9 Checksum Failure: 3.10.8 ISO15693 Write AFI Function: Write AFI to CURRENT TAG. Host sends: Frame 0x57 AFI Checksum AFI: 1 byte, AFI value to be written. Success: Frame 0x57 Checksum Frame 0xA8 Checksum Failure: 3.10.
PAGE 64
East Wind Technologies, Inc. Frame 0x59 DSFID DSFID: 1 byte, DSFID value to be written. Success: Checksum Frame 0x59 Checksum Frame 0xA6 Checksum Failure: 3.10.11 ISO15693 Lock DSFID Function: Lock DSFID of CURRENT TAG. Host sends: Frame 0x5A Checksum Frame 0x5A Checksum Frame 0xA5 Checksum Success: Failure: 3.10.12 ISO15693 Get Blocks Security Function: Get blocks security information of CURRENT TAG.
PAGE 65
East Wind Technologies, Inc. 3.11 I.CODE 1 Operation Commands 3.11.1 I.CODE1 Inventory Function: Search I.CODE1 card in RF effective field. Host sends: Frame 0x80 Checksum Frame 0x80 SNR 0x7F Checksum Success: Checksum SNR: 8 bytes. Failure: Frame 3.11.2 I.CODE 1 Read Function: Read data from I.CODE1. Host sends: Frame BlockNumber: Success: 0x81 BlockNumber Checksum 1byte, value: 0x00 to 0x0F. Frame 0x81 Data Frame 0x7E Checksum Checksum Data: 4bytes. Failure: 3.11.3 I.
PAGE 66
East Wind Technologies, Inc. 3.11.4 I.CODE 1 Stay Quiet Function: I.CODE1 stay quiet. Host sends: Frame 0x83 Checksum Frame 0x83 Checksum Frame 0x7C Checksum Success: Failure: Copyright © 2022 East Wind Technologies, Inc. All rights reserved.
PAGE 67
East Wind Technologies, Inc. 3.12 Felica Card Commands 3.12.1 Send APDU to Felica card Function: Use this command to send / receive APDU to / from Felica card. Host sends: Frame 0x2F APDU command Checksum APDU: Please refer to Felica user manual for detailed APDU command. Success: Frame 0x2F Response Checksum Response: Felica card answers. Response length depends on each command. Failure: Frame 0xD0 Checksum 3.12.2 Polling Function: Use this command to acquire and identify a card.
PAGE 68
East Wind Technologies, Inc. becomes 0001b. • Manufacture Parameter (PMm) PMm consists of IC Code (2 Bytes) and the maximum response time parameters (6 Bytes). o IC Code (2 Bytes) This is the information to identify a product. IC code consists of two components, i.e., ROM Type and IC Type. o Maximum response time parameters (6 Bytes) The timeout time is determined, based on the period of time necessary to process the commands.
PAGE 69
East Wind Technologies, Inc. Response: Felica card answers. Failure: Frame 0xD0 Checksum Example: Send: 0x22 2F 20 08 01 2E 3D 23 BA 07 5C 45 01 09 00 01 80 00 11 22 33 44 55 66 77 88 11 22 33 44 55 66 77 88 Response: 0x0E 2F 0C 09 01 2E 3D 23 BA 07 5C 45 00 00 19 Copyright © 2022 East Wind Technologies, Inc. All rights reserved.