Product Information

©2019 HEALTHE INC. ALL RIGHTS RESERVED
HEALTHE_SunLyncManual_02112019_v6kk.pdf
Included:
SunLync, USB Charger,
USB-A to USB-C Cable
FCC: 2AJFLACC07015
INITIAL SETUP BUTTON COLOR CODE
1
Via Wired Switch
Locate a spot where a GPS signal
can easily be acquired and plug your
SunLync into the included USB charger.
Turn off the light fixture
Turn on the light fixture for 2 seconds then turn off.
Turn on the light fixture for at least 5 seconds
Repeat the above three steps (up to 4 times, depending on current
setting) until the light fixture flashes once, indicating AUTO mode
has successfully been entered.
2
Press and hold the button until it turns
GREEN, then release the button.
The green lit button will begin flashing.
3
Wait until the button remains green
for 5 seconds.
Solid Green
4
Color Meaning
You have successfully setup SunLync,
it will take it from here.
The SunLync is working properly.Flashing Green
Every 6 seconds when plugged in
or every minute otherwise
The SunLync is looking for a GPS signal.Flashing Green
Every 3 seconds
5
See the reverse side for setting up your
SunTrac Lighting product(s).
The SunLync has successfully acquired
a GPS signal.
Solid Green
For 5 seconds
The SunLync is working properly but the
battery is low. Plug it into the USB charger.
Flashing Red
Every minute
The SunLync has been plugged in
and is charging.
Solid Blue
For 5 seconds
Either the SunLync was unable to locate
a signal or the battery is low.
Plug it in for at least 10 minutes, then proceed
to an outdoor location and try again.
Solid Red
For 5 seconds
Via Paired SunTrac Switch App
Tap the ‘AUTO’ button after tapping ‘Advanced’ button. The ‘AUTO’ button
will be highlighted yellow.
The light fixture will flash once, indicating AUTO mode has successfully
been entered.
Via Paired SunTrac Wireless Switch
Press and release the S1 button three times as shown
in the image below.
The light fixture will flash once, indicating AUTO mode has
successfully been entered.
Turn On Light (S1)
Welcome to your smart (and healthy) lighting solution!
As part of the SunTrac™ lighting ecosystem, SunLync
enables you to experience the right light at the right
time of day with the simple touch of a button.
SunLync
™
In order to run the preconfigured light show, SunTrac lights need to be in
AUTO mode. If you manually adjust the spectrum or intensity of the
lights they will remain at that manual setting until you return to AUTO
mode and are again paired with your SunLync.
For detailed product information,
support and other Healthe solutions,
visit www.healthelighting.com
RF Exposure Information and Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna
or transmitter.
Changes or modifications made to this equipment not expressly approved by the manufacturer may void the
FCC authorization to operate this equipment.