ELECTRIC SKATEBOARD Remote Model:R2B
REMOTE SCREEN GUIDE A B C 175mm 66T Trip: 0 90% D E F km/h G 0.0 km H A. Speed mode E. Gear Setting B. Bluetooth Connection F. C. Board Battery G. Speedometer D. Remote Battery H.
REMOTE MENU CONTROLS To access the menu, turn the remote on, then double tap the ON/OFF BUTTON. When in the menu use MODE 1 and MODE 2 to navigate/scroll through menu lists. Use the ON/OFF BUTTON to confirm selections.
PAIRING / SYNCING THE REMOTE 1. Turn the skateboard on. 2. Turn the remote on. 3. Press and hold the MODE 1 BUTTON on the remote for one second or until the Bluetooth symbol begins to flash. 4. Once paired, the Bluetooth symbol will switch to a solid symbol and the battery display will show a reading. This means you are ready to ride! 1 2 3 4 175mm 66T ON / OFF MODE 1 x1 1 Sec ON / OFF Trip: x1 0 90% km/h 0.
CHANGING SPEED MODES ON THE REMOTE Once your remote is on and paired to your skateboard it will begin in ‘SAFE MODE’ as the first speed mode setting. Now press either MODE 1 or MODE 2 button once, this will change the speed from SAFE MODE to the previous speed setting of your last ride. MODE 1 BUTTON MODE 2 BUTTON Each time you press the MODE 1 BUTTON, this will INCREASE the speed mode from ECO MODE through to CUST MODE.
Each time you press the MODE 1 or MODE 2 button to change your speed settings the remote will vibrate one time giving warning the speed mode has changed. The speed mode is clearly displayed in the top left corner of your LCD screen. ECO SPEED MODE Economical cruising mode with 75% of top speed. Best for beginners and longest ride times. PRO SPEED MODE Fast acceleration, can reach top speed, good for smaller hills and short grass.
SAFETY SWITCH The SAFETY SWITCH is located under the accelerator trigger. It must be pressed by your 2nd and/or 3rd finger as you engage the accelerator trigger to begin riding. The speed mode display on the LCD screen will turn a solid color once you press in the SAFETY SWITCH. IF YOU DO NOT PRESS THE SAFETY SWITCH IN AS YOU ENGAGE THE ACCELERATOR TRIGGER, THE BOARD WILL NOT MOVE.
HOW TO ACCELERATE With the safety switch depressed, pull the ACCELERATOR trigger slowly and you will begin to move forward. The further you pull the trigger in, the faster you will go. Once over 5km/h you can release the safety switch. For more information refer to the SAFETY SWITCH section.
HOW TO BRAKE Push the brake trigger forward SLOWLY and you will begin to slow down. The further you push the trigger, the stronger the braking will be. When riding very slowly the brakes will be softer than when you are riding at a higher speed. Have your weight on the back foot when you apply the brake function to stop you from flying forward when applying the brakes.
CONTROLLING THE BOARD The board is controlled by a combination of the rider and remote. The rider operates the remote which controls accelerating and braking. Turning and stability is dependent on the rider. To turn the board the rider must lean in the direction they wish to turn. To keep stable, it is recommended to stay relaxed, so that your body can absorb bumps and movements created by the terrain or remote input.
CHANGING WHEEL AND GEAR SETTINGS Be sure to select the right wheel and gear combination you are riding with, as this will give you an accurate speed and trip distance display on your remote. The wheel and gear settings are displayed in the top left corner of the LCD screen. 1. From the default screen, double-tap the ON/OFF BUTTON. This will now display the menu screen. 2. Wheel Setting will be the first option, press the ON/OFF BUTTON to select it.
SELECT KMH OR MPH 1. From the default screen, double-tap the ON/OFF BUTTON. This will now display the menu screen. 2. Scroll down by pressing the MODE 2 BUTTON until you reach ‘Options’, then press the ON/OFF BUTTON. 3. Press the ON/OFF BUTTON to change the unit of measurement for your region (KMH or MPH). 4. Once selected, press the MODE 2 button to move the highlighted box to the ‘Return’ selection, then press the ON/ OFF BUTTON.
BATTERY INDICATOR DISPLAY When the remote is connected to the board, it will display how much battery is left in the skateboard and remote in real time. The battery of the skateboard is displayed as a small percentage symbol (%) in the top right-hand corner of the LCD screen, and as a small battery bar under the percentage symbol for the remote battery. 175mm 66T Trip: 0 90% SKATEBOARD BATTERY % REMOTE BATTERY % km/h 0.
CHANGE BATTERY INDICATOR DISPLAY You have the option to change the skateboard battery percentage display to a skateboard battery bar if you prefer. 1. Double-tap the ON/OFF BUTTON. This will now display the menu screen. 2. Scroll down by pressing the MODE 2 BUTTON until you reach ‘Options’, then press the ON/OFF BUTTON. 3. Use the MODE BUTTONs to scroll through to the ‘Battery’ selection then press the ON/OFF BUTTON to change from ‘Dig’ (percentage) to ‘Bar’ or vice versa. 4.
LOW BATTERY WARNINGS ON THE REMOTE There are low battery warnings set on the remote that provide you with notice of when to expect the skateboard to run out of power. See below at what stage the warnings come on: 1. At 10% the remote will vibrate quickly one time. 2. At 5% the remote will vibrate once every 5 seconds. 3. At 1% the remote will vibrate for 5 seconds with a brief pause then continue to vibrate. 4. At 0% the remote will continue to vibrate then go into ECO MODE.
TRIP METER The trip display will show your distance travelled for your current ride only. Once you turn your board off the trip meter will reset itself and return to 0 value. 175mm 66T Trip: 0 90% km/h 0.0 km TRIP METER NOTE - FOR BEST ACCURACY, BE SURE TO HAVE SELECTED THE CORRECT WHEEL AND GEAR SETTING SIZE ON YOUR REMOTE. IF THE INCORRECT SELECTION IS BEING USED ON THE REMOTE, THE REMOTE WILL GIVE THE INCORRECT SPEED AND TRIP DISTANCES.
AUTO SAFE FUNCTION The auto safe function is a feature of the remote that is designed to detect any potential issues with the control of the board. This can relate to anything to do with the battery performance, motor controller performance and remote operational control. The auto ‘Safe’ mode will be activated if any of the above is disturbed, even if it’s minor, the remote will detect and make the control go to safe mode.
POWER SAVE FUNCTION To maximize the battery run time in the remote, there is a power save function that makes the remote screen turn off when the remote is at a low angle. Power save will automatically activate one minute after the remote is turned on. When the rider lifts the remote to a more level position, it will turn back on. To deactivate/reactivate this function, go into the ‘Options’ section of the remote menu and change the settings for ‘Power Save’.
SPEED LIMITER The speed limiter has been designed to cap top speeds for certain country laws as well as for those riders who are happy only to ride at a certain speed. The power and torque is still exactly the same when the limiter is activated, however the top speed is limited. To access the speed limiter, follow these steps: 1. Double click the ON/OFF BUTTON on your remote. This will bring you into the main menu screen. 2.
R2 TRIGGER RESET PROCEDURE If for some reason you are experiencing symptoms such as difficulty changing speed modes, unable to turn the remote off before the board and ability to brake but not accelerate, this is usually caused by knocks to the remote which then moves the triggers from its original position within the remote case. In most cases this can be resolved by resetting the acceleration and brake trigger settings bringing it back to factory settings.
4. Perform the following sequence of button presses: Double click ON/OFF BUTTON. Double click MODE 2. Double click MODE 2 again. A B C MODE 2 MODE 2 x2 x2 ON / OFF x2 The remote should now be in the trigger setting screen 5. With ‘Set ACC Min’ highlighted, pull and hold the ACCELERATOR TRIGGER all the way in. Press the ON/OFF BUTTON once to set the value.
7. With ‘Set Brake Min’ highlighted, release the BRAKE LEVER entirely and press the ON/OFF BUTTON once to set the value. A B C Acc Trigger: XXXX Brake Trigger:XXXX Throttle: X Set Acc Min: Set Acc Max: Set Brake Min: Set Brake Max: return XXXX XXXX XXXX XXXX ON / OFF x1 8. With ‘Set Brake Max’ highlighted, press and hold the BRAKE LEVER all the way in. Press the ON/OFF BUTTON once to set this value. Once the ON/OFF BUTTON is pressed the BRAKE LEVER can be released.
OTHER REMOTE OPERATION FUNCTIONS AND TIPS • If you accidentally press both the accelerator trigger and brake trigger at the same time, the brake function will work and cancel out the accelerator. • If you hold down the accelerator and brake triggers then let the brake trigger go it will not accelerate. • As you are riding and holding down the accelerator or brake trigger, you will not be able to change speed modes or turn the remote off until you let the triggers go.
HEAT PROTECTION WARNING To protect the entire electric system from over heating, we have created software that is designed to reduce the board performance. This forces it to cool down and prevent the rider continuing to put stress on the electric system. If ever the system does reach this protection mode, the remote will automatically go to PRO speed mode and will vibrate one time and the km/hr reading will change to a red colour.
ERROR CODES If ever the board experiences an operational issue, an error message will be detected by the remote and displayed in the ‘More Info’ screen. See below the list of Error Codes: ‘BATT ERR’ This error code may be displayed if there is an error in communication between the BMS and motor controller. In the event this occurs, the board will limit the speed mode to SAFE MODE to reduce the risk of damage to the battery.
MAINTENANCE GUIDE If you regularly clean and maintain your electric longboard, it will last a long time and ride at its best: • Always clean your bearings for best roll and quietest/ smoothest ride. Bearings get dirty and affect ride quality which may reduce battery performance and cause possible bearing failure. • Always check all screws/nuts throughout the skateboard are tight (truck nuts, wheel nuts etc). You are responsible for this.
BATTERY CARE Your battery and therefore your board, should always be stored at room temperature. Excessive heat can permanently affect or damage the battery. The board does have heat protection software in place should this occur whilst riding to prevent the battery from overheating. If left in a hot car, hot environment or exposed to other factors that may cause excessive heat, the heat protection software can’t reduce temperatures, and your battery may be affected.
TROUBLE SHOOTING This manual is a quick start guide only. For detailed information regarding tips, maintenance and trouble-shooting, please visit WWW.EVOLVESKATEBOARDS.COM. Here you will find links to your local distributor for detailed information. WARRANTY THIS BOARD IS COVERED BY A 12 MONTH MANUFACTURERS WARRANTY (TIME PERIOD MAY BE DIFFERENT IN OTHER COUNTRIES SUCH AS USA AND EUROPE) THAT COVERS DEFECTS IN WORKMANSHIP AND MATERIAL.
/48
FCC Statement: This device complies with part 15 of the FCC rules Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.