027-0001B, 027-0002B, 027-0003B, 027-0004B, 027-0006B Original Instructions GB2438285 Original written in UK English Date Published:25/07/2018
www.evolutionpowertools.
www.evolutionpowertools.com (1.2) INTRODUCTION IMPORTANT Please read these operating and safety instructions carefully and completely. For your own safety, if you are uncertain about any aspect of using this equipment please access the relevant Technical Helpline, the number of which can be found on the Evolution Power Tools website. We operate several Helplines throughout our worldwide organization, but Technical help is also available from your supplier. EN (1.3) CONTACT: Web: www.
www.evolutionpowertools.com SPECIFICATIONS MACHINE SPECIFICATIONS CCSL Motor EU/AUS (220-240V ~ 50 Hz) 1200W Motor UK (110V ~ 50 Hz) 1200W No-Load Speed (min-1/rpm) 3700 Weight 4.2kg Dust Port Diameter Ø 30mm Max. Blade Bevel Angle (degrees) 450 Power cable length 3m CUTTING CAPACITIES CCSL Mild Steel Plate (Max Thickness) 3mm Mild Steel Box Section (Max.
www.evolutionpowertools.com VIBRATION (1.5) Note: The vibration measurement was made under standard conditions in accordance with: EN 62841-1: 2015, EN 62841-2-5: 2014 Warning: Wear hearing protection! The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. The declared vibration total value may also be used in a preliminary assessment of exposure.
www.evolutionpowertools.com (1.9) INTENDED USE (1.8) Symbol Description V Volts A Amperes Hz Hertz Min-1 /rpm Speed ~ Alternating Current no No Load Speed OF THIS POWER TOOL WARNING: This product is a Hand Operated Circular Saw and has been designed to be used with special Evolution blades. Only use accessories designed for use in this machine and/or those recommended specifically by Evolution Power Tools Ltd.
www.evolutionpowertools.com (1.13) OUTDOOR USE WARNING: For your protection if this tool is to be used outdoors it should not be exposed to rain, or used in damp locations. Do not place the tool on damp surfaces. Use a clean, dry workbench if available. For added protection use a residual current device (R.C.D.) that will interrupt the supply if the leakage current to earth exceeds 30mA for 30ms. Always check the operation of the residual current device (R.C.D.) before using the machine.
www.evolutionpowertools.com A wrench or key left attached to a rotating part of a power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
www.evolutionpowertools.com You should always: • Work in a well-ventilated area. • Work with approved safety equipment, such as dust masks that are specially designed to filter microscopic particles. h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
www.evolutionpowertools.com d) Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback. e) Blade depth and bevel adjusting locking levers must be tight and secure before making a cut. If the blade adjustment shifts while cutting it may cause binding and kickback. f) Use extra caution when sawing into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
www.evolutionpowertools.com (4.2) ITEMS SUPPLIED Description CCSL Instruction Manual 1 Multi-Material TCT Blade 1 Hex Key (Blade Change) 1 Parallel Edge Guide 1 Dust Port Adapter 1 Dust Hose Adapter 1 EN 4.3) Evolution Instruction Manuals Evolution Power Tools provides each product with an Instruction Manual. Each dedicated manual is carefully constructed and designed to provide easily accessible and useful information regarding the safe use, care and maintenance of the product.
www.evolutionpowertools.com MACHINE OVERVIEW 1 16 15 2 14 3 13 4 12 5 11 10 6 9 7 8 1. CUT MATERIAL EJECTION PORT 10. DEPTH SCALE 2. THUMB LEVER 3. MULTI-MATERIAL TCT BLADE 11. REAR HANDLE INCORPORATING SAFETY START ON/OFF SWITCH 4. LOWER BLADE GUARD 12. UPPER BLADE GUARD 5. PARALLEL EDGE GUIDE 13. PRECISION ENGINEERED SOLE PLATE 6. ERGONOMIC FRONT HANDLE 14. THUMB LEVER 7. CARBON BRUSHES 15. PROTRACTOR SCALE 8. ALLEN KEY (BLADE CHANGE) 16. ARBOR LOCK BUTTON 9.
www.evolutionpowertools.com (10) PREPARATION (All R185 CCS Machines) WARNING: Always disconnect the machine from the power source before making any adjustments. Note: These machines are equipped with an approved power cord and plug for the intended country of use. Do not alter or modify the power cord. EN (10.1) INSTALLING/REMOVING A BLADE WARNING: Use only genuine Evolution blades (or those approved by Evolution Power Tools), which are designed for use in these machines.
www.evolutionpowertools.com • Safely store the outer blade flange and associated fixings. • Rotate the lower blade guard up into the upper blade guard using the manual thumb lever. (Fig. 5) • Carefully remove the blade (if fitted) from the machine. • Thoroughly clean inner and outer blade drive flanges. Fig. 5 Fig. 6 Note: The inner blade flange can be left in place if desired, but it should be checked and thoroughly cleaned.
www.evolutionpowertools.com WARNING: It is potentially dangerous to install, and try to use the Edge Guide with the arm passing through only one (1) of the machined rectangular sole plate slots. Adjust the edge guide so that it is at the required distance from the blade and tighten the adjusting screw. Check that the edge guide is parallel to the saw blade.
www.evolutionpowertools.com If a very precise bevel angle is required, then the blade setting should be checked using a vernier angle gauge (not supplied) and adjusted accordingly. • Loosen the Bevel Locking Mechanism found at the front of the machine, by pulling the lever upwards. (Fig. 13) • Tilt the blade to the required angle as indicated on the quadrant protractor scale. (Fig.
www.evolutionpowertools.com (15) PPE • The operator should wear all relevant PPE (Personal Protection Equipment) necessary for the task ahead. This could include safety glasses,,full face mask, dust masks, safety shoes etc. Note: All CCS series machines are equipped with a cutting line debris blower. This directs air from a motor driven fan towards the area to the front of the blade, thus keeping the cutting line relatively debris free.
www.evolutionpowertools.com (17) CUTTING ADVICE A thumb operated lever is provided on the lower blade guard. With care, a skilled operator can retract the blade guard manually, either partially or fully, allowing plunge cuts to be made. WARNING: The operator must always be aware of the position and routing of the power cable. The cable must be routed in such a way that there is no possibility of the blade coming into contact with the mains cable.
www.evolutionpowertools.com Note: The lower blade guard should be rotated (manually) up into the upper blade guard. This will help accurate positioning of the engineers square and thus aid the checking process. If adjustment is required: CCSL Turn the adjustment screw (Fig. 16) clockwise or counter clockwise using a Hex Key (not supplied) until the blade is at exactly 900 to the sole plate. (19) CHECKING AND REPLACING EN Fig.
www.evolutionpowertools.com (20) GENERAL MAINTENANCE & CLEANING Note: All maintenance must be carried out with the machine switched off and disconnected from the power supply. • Check that all safety features and guards are operating correctly on a regular basis. Only use this machine if all guards/safety features are fully operational. • All motor bearings in these machines are lubricated for life. No further lubrication is required.
www.evolutionpowertools.com EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below.
AUS FR T: 03 9261 1900 T: +33 (0)5 57 30 61 89 UK USA T: +44 (0)114 251 1022 T: 866-EVO-TOOL Total Tools (Importing) Pty Ltd 20 Thackray Road Port Melbourne Vic 3207 Evolution Power Tools SAS 61 Avenue Lafontaine 33560, Carbon-Blanc Bordeaux Evolution Power Tools Ltd Venture One, Longacre Close Holbrook Industrial Estate Sheffield, S20 3FR Evolution Power Tools LLC 8363 Research Drive Davenport, IA 52806 DE +44 (0)114 251 1022 ES +34 91 114 73 85 NL +44 (0)114 251 1022 PL +48 33 822 09 22 PT +34
