Integration Manual

ManualsBrandsEVOLIS ManualsElectronicsRFID module CP013463

Table Of Contents

RFID Module CP013463 INTEGRATION MANUAL

2021-10-15

1/6

RFID module CP013463 FCC Certification

The OEM Integrators are responsible for ensuring that the end-user has no manual

instructions to remove or install module.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

Authorized antennas:

The antenna is fixed and integrated in the reader. It cannot be removed..

The module is limited to OEM installation ONLY

This modular is used exclusively by Evolis

This equipment complies with FCC’s radiation exposure limits set forth for an

uncontrolled environment under the following conditions:

1. This equipment should be installed and operated such that a minimum separation

distance of 20cm is maintained between the radiator (antenna) and user’s/nearby

person’s body at all times.

2. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

The RF module has been certified for mobile and fixed applications. If the module will be

used for portable application the device must undergo SAR testing or MPE evaluation.

In this case, a separate approval is required for all other operating configurations.

Any changes or modifications to this module not expressly approved by Evolis may

cause, harmful interference and void the FCC authorization to operate this equipment

Summary of content (6 pages)

PAGE 1
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 RFID module CP013463 FCC Certification The OEM Integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Moreover, the host equipment must be labelled as follows: Contains Transmitter Module FCC ID : ZFX0011 or Contains FCC ID : ZFX0011 “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Additional information RFID module CP013463 should only be used on Evolis printer. RFID module CP013463 should only be installed by a Evolis technician. 1) The shielding of RF is provided by the printer frame. The printer frame is made of XC steel or plastic carbon force. 2) Power supply regulation is provided by the motherboard. The motherboard provides +3.3 volts.
PAGE 4
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 RFID module CP013463 IC Certification This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 5
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Cet équipement est conforme aux limites d’expositions de la CNR102 applicables pour un environnement non contrôlé aux conditions suivantes : 1. Cet équipement devra être installé et fonctionner de telle manière qu’une distance minimale de séparation de 20 cm soit maintenue entre la partie rayonnante (l’antenne) et l’utilisateur / les personnes à proximité à tout moment.
PAGE 6
RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Spécificité du module RFID CP013463 Le module RFID CP013463 ne doit être utilisé que sur des imprimantes EVOLIS. Le module RFID CP013463 ne doit être installé que par un technicien Evolis. 1) Le blindage de la zone RF est assuré par le châssis de l’imprimante qui est soit métallique (Acier XC) ou en plastique chargé carbone. 2) L’alimentation régulée 3.3 volts est assurée par le carte mère de l’imprimante.