User's Manual

ManualsBrandsEverspring Industry ManualsCamera & PhotoBaby Camera

Installation and Operating Instruction

Product Layout

Camera

(Fig. 1)

① Low battery indicator LED

② Power indicator LED

③ Microphone

④ Infrared LEDs

⑤ Lens

⑥ Keyholes

⑦ Battery compartment

⑧ 6V DC power adaptor jack

⑨ Learn button

⑩ Power On/Off switch

⑪ Channel selection switch

Fig. 1

Monitor

(Fig. 2)

① Sensitivity level control

② Volume/power control

③ Brightness/contrast ratio control

④ Speaker

⑤ LEDs indicator

⑥ 6V DC power adaptor jack

⑦ Hang up hole

⑧ Keyholes

⑨ Swiveling pivot

Fig. 2

Kit Content

1 x Camera 4 x 1.5V AA-size Battery (for

Monitor)

1 x Monitor All Fixing Screws

1 x AC/DC Adaptor (for Camera) This manual

Summary of content (9 pages)

PAGE 1
Installation and Operating Instruction Monitor (Fig. 2) Product Layout ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ Camera (Fig. 1) ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ Low battery indicator LED Power indicator LED Microphone Infrared LEDs Lens Keyholes Battery compartment 6V DC power adaptor jack Learn button Power On/Off switch Channel selection switch Sensitivity level control Volume/power control Brightness/contrast ratio control Speaker LEDs indicator 6V DC power adaptor jack Hang up hole Keyholes Swiveling pivot Fig.
PAGE 2
Introduction Camera. The specification of AC/DC adaptor is 6V/500mA with regulator. (Fig. 4) Note: The AC/DC adaptor shall remain readily operable. This package is designed to facilitate the users who intend constant observation of the particular place where continuous caring or surveillance is needed. Both Camera and Monitor units are suitable for indoor use only. R O Either 4 AA-size batteries or an AC/DC adaptor can be used as their power source.
PAGE 3
Operating the Camera interference or other problems occur, refer to the Troubleshooting. You may need to select a different location in the room for mounting the Camera. 1. The ON/OFF slide switch is for turning on and off the power. (Fig. 9) 2. Up to four cameras can be connected to the Monitor. Set the channel switch (numbered 1~4) that matches to that of the Monitor you plan to observe. (Fig. 9) 1. Decide on the appropriate mounting location. Drill two holes 32mm apart in a line and fit wall plugs.
PAGE 4
There are 6 auxiliary infrared LEDs adjacent to the camera lens. They are designed to enhance low light level visibility. When the ambient light level is lower than 10 Lux, the infrared LEDs will start operating automatically, while if it is higher than 200 Lux, the infrared LEDs will shut down automatically. Keep a minimum distance of 30cm between infrared LEDs and observed object. Otherwise the camera is liable to make wrong judgement. 5. When the low battery LED lights up, replace batteries immediately.
PAGE 5
Operating the Monitor 1. Fig. 12 Free standing the Monitor The Monitor has the swiveling pivot which allows flexible angle adjustment for free standing installation. 1. Adjust the swiveling pivot to an appropriate angle for best viewing condition. (Fig. 13) Note: To meet various applications, the angle of swiveling pivot can attain 80° and 50°. 2. Place the Monitor to an ideal location. 2. Fig. 13 Hanging up the Monitor On the top of the rear of Monitor, penetrate a string through the hole. 3.
PAGE 6
the mode selection button (Fig. 15) on the front of Monitor. a. Audio/video mode: The Monitor is on continuously, emitting sound and image. Under this mode, both and LEDs will not illuminate. (Fig. 15) No matter what mode it is, simply enter Audio/video mode for impromptu surveillance. b. Audio mode: The Monitor only delivers audio and LED will light up. (Fig. 15) c. Audio-activated mode: This audio-activated mode allows you to set the sensitivity of audio level that will trigger the Monitor.
PAGE 7
LED Off Off On On LED off on off on Mode Audio/video Audio Audio-activated Auto scan 2. Volume/Power control: It allows you to adjust the audio level received from the Camera. (Fig. 14a) Note: The audio level can vary between 0 to 9. A value of 0 gives minimum level, a value of 9 gives maximum level. 3. CH selection button: 4 channels are available by pressing CH selection button on the front of the Monitor. (Fig.
PAGE 8
Monitor learnt the ID code successfully, but Monitor screen reveals “no signal” When learning the ID code from the Camera, interference by RF has occurred “No signal” is shown on the Monitor a. Interference by bluetooth or radio frequency or too far distance between Camera and Monitor b. Same channel has been set between Cameras c. Camera and Monitor do not set the same channel d. Does not proceed with learning the ID code c.
PAGE 9
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. - Reorient or relocate the receiving antenna.