User's Manual

ManualsBrandsEverspring Industry ManualsCamera & PhotoBaby Camera

Installation and Operating Instruction

Product Layout

Camera (Fig. 1)

? Low battery indicator LED

? Power indicator LED

? Microphone

? Infrared LEDs

? Lens

? Keyholes

? Battery compartment

? 6V DC power adaptor plug

? A/V IN

? Channel selection switch

? Night/color/power off switch

Fig. 1

Monitor (Fig. 2)

? Sensitivity level control

? Volume/power control

? Brightness/contrast ratio control

? Speaker

? LEDs indicator

? A/V OUT

? 6V DC power adaptor plug

? Hang up hole

? Keyholes

? Swiveling pivot

Fig. 2

Kit Content

1 x Camera 2 x AC Adaptor

1 x Monitor All Fixing Screws

2 x A/V cable This manual

Summary of content (7 pages)

PAGE 1
Installation and Operating Instruction Product Layout Monitor (Fig. 2) Camera (Fig. 1) ? ? ? ? ? ? ? ? ? ? ? ? Low battery indicator LED Power indicator LED Microphone Infrared LEDs Lens Keyholes Battery compartment 6V DC power adaptor plug A/V IN Channel selection switch Night/color/power off switch ? ? ? ? ? ? ? ? ? Sensitivity level control Volume/power control Brightness/contrast ratio control Speaker LEDs indicator A/V OUT 6V DC power adaptor plug Hang up hole Keyholes Swiveling pivot Fig.
PAGE 2
Introduction This package is designed to facilitate the users who intend constant observation of the particular place where continuous caring or surveillance is needed. Both Camera and Monitor units are suitable for indoor use only. Either 4 AA-size batteries or an AC adaptor can be used as their power source. When the battery level falls below an acceptable level, the “LOW BATTERY” indicator on the front of the Camera and Monitor will light up.
PAGE 3
1. 2. Operating the Camera Decide on the appropriate mounting location. Drill two holes 32mm apart in a line and fit wall plugs. (Fig. 6) Insert fixing screws until almost fully home and hang the Camera over these screws using the two keyhole slots in the rear of the Camera. (Fig. 6) 1. Set the channel switch (numbered 1~4) that matches to that of the Monitor you plan to observe. (Fig. 9) Fig. 6 Clipping on the Camera 1. 2. Use the clip as supplied for fixing the Camera on the crib or table edge.
PAGE 4
Loading the Batteries Installing the Monitor 1. 3 types of installation can be made, such as wall mount, table stand and hang up by string. Remove the power cavity from the rear of the Monitor. (Fig. 10) Wall Mounting the Monitor 1. 2. 2. 3. Decide on the appropriate mounting location. Drill two holes 48mm apart in a line and fit wall plugs. (Fig. 12) Insert fixing screws until almost fully home and hang the Monitor ove r these screws using the two keyhole slots in the rear of the Monitor. (Fig.
PAGE 5
Fig. 13 Hanging up the Monitor On the top of the rear of Monitor, penetrate a string through the hole. Operating the Monitor 1. Upon reception from the Camera, 3 modes can be selected by pressing the mode selection button on the front of Monitor. a. Audio/video mode: The Monitor is on continuously, emitting sound and image. Under this mode, both and LEDs will not illuminate. (Fig. 14) b. Audio mode: The Monitor only delivers audio and LED will light up. (Fig. 14) c.
PAGE 6
4. 5. Brightness/Contrast Ratio Control: The brightness and contrast ratio control for the Monitor can be adjusted by pressing the below button: (Fig. 14) : Increase brightness : Reduce brightness : Increase contrast ratio : Reduce contrast ratio When the battery level drops, the LED will be in red. Battery replacement should be taken as soon as possible. If everything is ok, the LED will be in green. device for signal transmission. (Fig. 17) 2.
PAGE 7
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.