User's Manual

ManualsBrandsEverspring Industry ManualsElectronicsOn/Off Plug with power meter

AN163 ON/OFF MODULE

This plug-in ON/OFF Module is a transceiver which is a Z-Wave

enabled device

and is fully compatible with any Z-Wave

enabled network. Z-Wave

enabled

devices displaying the Z-Wave

logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave

enabled

networks. Remote On/Off control of the connected load is possible with other

manufacturer’s Wireless Controller. Each module is designed to act as a repeater.

Repeaters will re-transmit the RF signal to ensure that the signal is received by its

intended destination by routing the signal around obstacles and radio dead spots.

This plug-in ON/OFF Module is able to detect current wattage (5~1440W) and

overload wattage of connected non-dimmable lights or appliances. When detecting

overload state, the Module will be disabled and its On/Off button will be locked out of

which LED will flash quickly for 30 seconds. However, unplug and re-connect the

Module will reset its overload condition to normal status.

Include to or Exclude from a Z-Wave

Network

In the front casing, there is an On/Off button with LED indicator which is used to carry

out inclusion, exclusion, reset or association. Toggle On/Off button between On and

Off. When first power is applied, its LED flashes on and off alternately and repeatedly

at 2-second intervals. It implies that it has not been assigned a node ID and cannot

work with Z-Wave enabled devices. Please get familiar with the terms below before

starting the operations.

Function Description

Inclusion Add a Z-Wave enabled device (e.g. On/Off Module) to Z-Wave network.

Exclusion Delete a Z-Wave enabled device (e.g. On/Off Module) from the network.

Function Description

Association After inclusion, you have to define the relationship between devices.

Through association, device can be assigned as master/slave, and specify

which slave is going to be controlled by which master.

Reset Restore On/Off Module to factory default.

The table below lists an operation summary of basic Z-Wave functions. Please refer

to the instructions for your Z-Wave

Certificated Primary Controller to access the

setup function, and to include/exclude/associate devices. The module executes the

function of auto inclusion when…

Auto Inclusion

The function of auto inclusion will be executed as long as the module does not have

a node ID and in situations where…

1. The power is first applied.

2. The execution of exclusion/reset is successful where the stored node ID is

cleared.

Note: Auto inclusion timeout is 4 minutes during which the node information of

explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as

shown in the table below, the execution of auto inclusion is free from pressing the

tamper switch on the unit.

Function Description LED Indication

No node ID The Z-Wave Controller does not allocate

a node ID to the Module.

2-second on, 2-second off

Inclusion 1. Have Z-Wave Controller entered

inclusion mode.

Press On, for on

Press Off, for off

2. Pressing On/Off button three times

within 1.5 seconds will enter

inclusion mode.

Exclusion 1. Have Z-Wave Controller entered

exclusion mode.

Press On, for on

Press Off, for off

2. Pressing On/Off button three times

within 1.5 seconds will enter

exclusion mode.

Node ID has been excluded. 2-second on, 2-second off

Reset 1. Pressing On/Off button three times

within 1.5 seconds will enter

inclusion mode.

Press On, for on

Press Off, for off

On /Off knob

Controllable outlet

Pass-through outlet

Summary of content (6 pages)

PAGE 1
Function Association AN163 ON/OFF MODULE This plug-in ON/OFF Module is a transceiver which is a Z-WaveTM enabled device and is fully compatible with any Z-WaveTM enabled network. Z-WaveTM enabled devices displaying the Z-WaveTM logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-WaveTM enabled networks. Remote On/Off control of the connected load is possible with other manufacturer’s Wireless Controller.
PAGE 2
. 3. Association Within 1 second, press On/Off button again for 5 seconds until LED is off. IDs are excluded. 1. Have Z-Wave Controller entered association mode. Or Pressing On/Off button three times within 1.5 seconds will enter association mode 2. There are two groupings - 1 and 2. Refer to Z-Wave’s Groups as described on page 3 & 4. 4. After putting it into use, the body of Module will become a little bit hot of which phenomenon is normal.
PAGE 3
1-2 BASIC_SET / SWITCH_BINARY_SET Upon receipt of the following commands from a Z-Wave Controller, the load attached to the Module will turn on or off. ALARM_REPORT Command: [Command Class Alarm, Alarm Type = 0x02, Alarm Level = 0x01] 2-1-2 On/Off Event Report (TRUE STATE) When toggling between “on” and “off ” button, it will send Switch Binary Report to the nodes of Grouping 1.
PAGE 4
. Meter Command Class 3. Z-Wave’s Configuration Configuration Function Parameter 1 Size Value Unit Default 0-120 100ms 10 The Module will report its instant or accumulated power consumption to Z-Wave Controller. If the calculation of accumulated power consumption is needed, the Z-Wave Controller needs to be sent Meter Reset Command to the Module, enabling to reset to zero.
PAGE 5
Rate Type = 0x01 Meter Type = 0x01 Precision = 2 Scale = 0x00 (KWh) Size = 4 (4 bytes Meter Value) Meter Value 1 = (W) MSB Meter Value 2 = (W) Meter Value 3 = (W) Meter Value 4 = (W) LSB * COMMAND_CLASS_METER_V2 * COMMAND_CLASS_ALARM * COMMAND_CLASS_CONFIGURATION Troubleshooting Symptom The Module not working and LED off Example: Scale = 0x00 (KWh) Precision = 2 Size = 4 (4 Bytes KW/h) Meter Value 1 = 0x00 Meter Value 2 = 0xB8 Meter Value 3 = 0x1A Meter Value 4 = 0x12 Cause of Failure 1.
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.