User Manual

ManualsBrandsEverFocus ManualsCamera & Photo2 Megapixel True Day/Night Outdoor IR Ball Camera, 2.8-12mm Lens

Table Of Contents

EBA1280 eZ.HD Series

1080p FHD IP66 IR Dome Camera

User’s Manual

Release Date: May, 2019

All the images including product pictures or screen shots in this document are for example

only. The images may vary depending on the product and software version. Information

contained in this document is subject to change without notice.

EverFocus Taiwan:

2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan

TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw

Summary of content (8 pages)

PAGE 1
EBA1280 eZ.HD Series 1080p FHD IP66 IR Dome Camera User’s Manual Copyright © EverFocus Electronics Corp. Release Date: May, 2019 All the images including product pictures or screen shots in this document are for example only. The images may vary depending on the product and software version. Information contained in this document is subject to change without notice. EverFocus Taiwan: 2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist.
PAGE 2
1. Introduction EverFocus eZ.HD series cameras – EBA1280 deliver 1080p full HD image quality. The model provides 2.8-12mm lens with ICR. Featured with Digital Wide Dynamic Range (D-WDR), the camera can provide clear images even under backlight circumstances where intensity of illumination can vary excessively. The EBA1280 supports both NTSC and PAL scanning systems and is IP66 certified. 1.
PAGE 3
1.3 Dimensions 60.2mm / 2.37" 98mm / 3.86" 120mm / 4.72" 1.4 Optional Accessory BA-E320 Color / Material: White / Metal Size (Φ x H): 138 x 54mm / 5.43”x2.13” Weight: 700g / 1.5lb BA-EB45 Color / Material: White / Metal Size (W x D x H): 245x160x163mm / 9.65”x6.3”x6.42” Weight: 2.1kg / 4.63lb 1.5 Cable Description 1 Power Cable 2 Video Output Cable No. Name Descriptions 1 Power Cable Connects to a 12VDC power source. 2 Video Output 1080p output, using 75 Ohm BNC-type coaxial cable.
PAGE 4
2. Installation 1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw positions. Drill four holes on the surface and insert the supplied 4 Screw Anchors into the screw holes. If you want to run the cable through the surface, drill a hole within the 4 screw area. 2. Unscrew the Outer Housing by twisting it counterclockwise and then remove it from the Camera Base. Camera Body Outer Housing Camera Base 3. Screw the Camera Base to the surface with the supplied four Screws. a.
PAGE 5
b. If you want to wire the cables through the surface: Attach and screw the Camera Base to the surface with the supplied 4 Screws, and then attach the Camera Body to the Camera Base. Camera Base Wall Camera Body 4. Screw back the Outer Housing and adjust the camera angle simultaneously. 180° 180° 360° 5. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a monitor or DVR. 6. For the first time installation, check whether the camera is properly focused.
PAGE 6
7. You can use the Joystick on the cable to configure camera OSD settings or switch to different video formats. Remove the Protection Cap from the Joystick before using it. Switching Video Format: • UP • • • Push the joystick up for 5 sec. to switch to AHD. Push the joystick right for 5 sec. to switch to TVI. Push the joystick down for 5 sec. to switch to CVI. Push the joystick left for 5 sec. to switch to CVBS. Configuring OSD Settings: • • • Push the Joystick up / down to select among menu items.
PAGE 7
3.
PAGE 8
9 10 11 Version Reset Save & Exit Exit Return Color Red/Green/Blue Transparency On/Off Return 7