EVS200A/EVS200AW User’s Manual Copyright © EverFocus Electronics Corp, Release: Sept. 2009 Rev.
EVS200A/EVS200AW Product Name: EVS200A/EVS200AW EverFocus 2CH Video Encoder Model Number(s): EVS200A/EVS200AW FCC Notice "Declaration of Conformity Information" RF Declaration should be added. Please check Safety team. This found to to comply with the the limits for afor Class A digital This equipment equipmenthas hasbeen beentested testedand and found comply with limits a Class device, pursuant part 15 of Rules. TheseRules.
EVS200A/EVS200AW EVS200A/EVS200AW complies with CE and FCC. About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notice -These limits are designed to provide reasonable protection.
EVS200A/EVS200AW remove, use a mild detergent and wipe gently. Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperature within 0℃ ~ +40℃ / 32℉ ~ 104℉ and a humidity below 90%. The input power source for this appliance is 12 VDC & PoE. Use only the recommended power supplies.
EVS200A/EVS200AW TABLE OF CONTENTS 1. INTRODUCTION....................................................................................................6 2. FEATURES ..............................................................................................................6 3. ACCESSING THE CAMERA MENU ...................................................................7 4. SETTING................................................................................................................10 4.
EVS200A/EVS200AW 1. INTRODUCTION The EVS200A/EVS200AW features H.264, MPEG-4 and MJPEG video signals, at up to 30fps, per channel, over IP networks. The video signals can be received and displayed with a standard web browser or Nevio Express management software. The EVS200A/EVS200AW provides Dual Streaming. It is able to generate in total 4 independently configurable H.264, MPEG4 or MJEPG video streams (2 per input).
EVS200A/EVS200AW Ultra-compact size for space-saving applications 3. ACCESSING THE CAMERA MENU Step 1.Start an Internet Explorer browser. Step 2. Enter the IP address or host name of the camera in the Location/Address field of your Internet Explorer browser. (Please refer to EVS200A/EVS200AW Installation Guide for how to find the IP address) Step 3. Input “Username” and “Password”. Default Username is “user1” and default password is “11111111”. Step 4. Click “Login” button. Step 5.
EVS200A/EVS200AW 1. Press button to display the "Live" page. Double click on the image to show a full screen display, double click again or press ESC to return normal display. 2. Press Playback button to start playback. 3. Press button to enter Setting page. In Setting page, there are 8 sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event] and [System]. Please refer to “4. SETTING” for further information. 4. Press button to close the network page. 5.
EVS200A/EVS200AW image file is saved can be specified in Setting -> User’s Config. Please refer to “4.2 User Config” for further information. Note: Record segment is limited to 1 min. If you need to do long time recording, please set schedule recording. For more details about schedule recording, please see “4.7 Event”. 9. Snapshot The Snapshot button saves a snapshot of the video image currently being displayed. The location where the snapshot data is saved can be specified in Setting -> User’s Config.
EVS200A/EVS200AW about Motion setup. 4. SETTING Click this button to display the setup menu. 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab. 4.1.1 Information System Information: Firmware version, MAC address, Video Type, Model number.
EVS200A/EVS200AW 4.1.2 Log System Log: Date/Time: displaying date and time of the log. Log message: all information and event message, including login, user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records.
EVS200A/EVS200AW Press button to export system log into “.txt” file and select the location where the exported log file will be saved to. 4.2 User Config Live view configuration is to be set by user. Each login user can make his/her own settings for the following items: Text Setting Check the box for text of Machine name, Date/Time or Frame Rate to be displayed on the screen.
EVS200A/EVS200AW change. Date/Time Format Used in Text Select Date/Time Format from the following options: Time Format: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snapshot Export Setting Enable Event Recording to PC: Allow event video recorded to users' PC if any events have been set to record to PC. Export folder: Select Export folder by clicking on folder to be exported.
EVS200A/EVS200AW English. To add a new language which is not listed in the original configuration, press the Browse button to locate the new language file (.evb) and then click the Load button. Note: Upload a new language file will reboot system automatically. Please reconnect IP camera after reboot. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.
EVS200A/EVS200AW the network administrator or your Internet service provider. • IP Type • IP address • Subnet mask • Gateway (when using the gateway server/router) • Primary DNS, Secondary DNS (when using DNS) IP Type DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for the settings of the server. Default: DHCP. Static IP: User can manually set the static IP for network connection.
EVS200A/EVS200AW If your ISP provides you an IP address secondary DNS, please set it here. Username Enter User name of the account (used only for PPPoE). Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.2 DDNS DDNS setting When accessing the camera via the Internet from the network environment of which the global IP address is obtained using DHCP, the DDNS function is necessary.
EVS200A/EVS200AW ○ www.no-ip.com Enable: Check the box to enable DDNS setting. Service ISP: If you choose EverFocus DDNS server, you can obtain a free account name from EverFocus ”www.everfocusddns.com”. Enter an IP Cam Account Name: Press .everfocusddns.com button to register or update DDNS account. If you wish to get a domain name from other DDNS provider, it is necessary to configure Record ID, FQDN, Username and password and register in DDNS server.
EVS200A/EVS200AW Max. Client Limit: enter a value here to restrict the number of clients accessing the camera. This is useful if you need to save on bandwidth. Up to 32 clients is allowed to see live video simultaneously. Subsequent viewers will see a blank image. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.
EVS200A/EVS200AW User name: Input the login user ID if the SMTP server requires Authentication. Password: Input the password if the SMTP server requires authentication. Receiver Address: Input the e-mail address for receiving e-mail message when the EVENT is enabled and triggered. Please use “;” to separate address. Sender Address: Input sender’s e-mail address, so that receiver can recognize the sender when an event message is sent out. Send Test Mail: Press address.
EVS200A/EVS200AW 4.3.5 Network Alarm (reserved for PowerCon) Set Network Alarm This function is reserved for PowerCon software, for the detail setting please refer to PowerCon network alarm protocol.
EVS200A/EVS200AW 4.3.6 Wireless Wireless Setting Enable Wireless (Default: disable) SSID: Name of the wireless network the camera is configured for. The field accepts up to 32 alphanumeric characters. (Default: default) Network Type: Infrastructure or Ad-Hoc (Default: Infrastructure) “Infrastructure” Make the Network Camera connect to the WLAN via an Access Point. “Ad-Hoc” Make the Network Camera connect directly to a host equipped with a wireless adapter in a peer-to-peer environment.
EVS200A/EVS200AW “Shared” – allows communication only with other devices with identical WEP settings. Key Length: 64 or 128 bits (Default: 64 bits) Key Format: HEX or ASCII (Default: HEX) Network Key: Entering a key in either hexadecimal or ASCII format. Confirm Key: double confirm network key. When selecting WPA-PSK/WPA2-PSK: WPA (Wi-Fi Protected Access) key should follow either one of the following rules: - As 64 hexadecimal (0-9, A-F) characters. - As 8 to 63 ASCII characters.
EVS200A/EVS200AW 4.4.1 Multi Streaming Stream Setting The system can output 4 video streams simultaneously. For each of them, user can set compression format, resolution, quality and frame rate individually. Stream 1 is always enabled for live view. Check “Enable” box to enable other streams. Format: Select encode format from H.264, MPEG4 and MJPEG.
EVS200A/EVS200AW Note: Total frame rate cannot exceed 60 fps. System performance may be influenced if user enables 4 video streams simultaneously. Press Apply to apply the setting changes or Reset to reset without saving the change. Video Recording Setting User can set video recording by selecting one of the enabled video streamings. This will allow user to view live images as well as to record video of the other video streaming. Video Stream: Select video recording stream from any enabled stream.
EVS200A/EVS200AW 4.4.2 Video - Display Setting Select a channel: add channel selection. Channel title: add channel title. PTZ function: select PTZ function ON or OFF Brightness/ Contrast/Hue: add the adjustment to brightness, contrast and hue Note: 1. There is no Apply button, whenever the above three picture parameters are adjusted, the values will be set to the channel 2. Click “Reset” to reload to the original value when just jump into this page 4.
EVS200A/EVS200AW Audio Check Enable Audio box to enable audio function. Audio Input: Audio from an internal microphone or a line source can be connected to the Audio connector of EVS200A/EVS200AW. The audio source can be selected from Internal Microphone, External Audio Input L and External Audio Input R. Audio Input volume: Adjust the Audio Input Volume for the audio input devices connected to the camera if there are problems with the sound input being too low or high.
EVS200A/EVS200AW User Information Maximum 10 users can be set for using the IP camera. The user information displays the authorized users and access levels: • Supervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menu and can determine the registration of all other users. However, administrator is not allowed to change supervisor’s account and password. • User- a user can view the Live View page, system info, network, video, audio, and adjust user config settings.
EVS200A/EVS200AW to be performed. The event type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event type. Event Type Action Type Alarm Input Manual Trigger Motion Detection Schedule Recording Trigger Alarm x x x Send Mail notification x x x Upload to FTP** x x x Record to SD Card x x x x x Record to PC* x x x x x Network Alarm x x x Re-trigger x x x Pre/Post-Alarm x Note: 1.
EVS200A/EVS200AW Press button to add an event condition. To modify the event list, click on the event and it will be highlighted. Press button to modify the setting. To remove an event from event list, click on the event and it will be highlighted. Press button to remove the event. Check Enable checkbox to activate event actions when the event occurs in the specified time zone. To change the priority of events, click on the event and it will be highlighted. Press or button to move between events.
EVS200A/EVS200AW This example describes how to set the camera to upload images to FTP when someone press Manual trigger button: button in Event page. 1. Click 2. Enter an event name for the event, e.g. Event 1 3. Select “Manual Trigger” as event type. 4. Select “Upload to FTP” as action type. 5. Check “Enable Pre-alarm Buffer” and “Enable Post-alarm Buffer”. For pre-and post alarm buffer setting, please refer to “4.7.3 Alarm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask.
EVS200A/EVS200AW 4.7.2 Motion Motion Detection First, select the channel for motion detection setting. User can define the motion area to be detected by left clicking the mouse to draw lines. Every click is an end point of the line. When the detection area is formed, double click the mouse to have all the lines connected. To remove the selection, simply right click the mouse, the selected polygon will be deleted. Press All Areas to have the entire screen selected for motion detection.
EVS200A/EVS200AW Alarm Output Setting Contact Type: Normal Close, Normal Open Duration Time: Select duration time of alarm output from 5 sec, 10 sec, 20 sec, 30 sec, 60 sec, 2 min, 3 min and 5 min. Press Apply to apply the setting changes or Reset to reset without saving the change. Pre/Post Alarm Setting This function is used to check what happened immediately before and after a trigger, e.g. 5 seconds before or after a motion has been detected.
EVS200A/EVS200AW Re-trigger Filter: Set a re-trigger filter time, if another event is triggered during this time, this triggered event will be ignored. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.7.4 Time Mask Time Mask Setting Time mask setting allows you to schedule event actions. Select Always for event action to be taken continuously. Press button to add new time period. Mask name: Input a mask name for the new time period.
EVS200A/EVS200AW 1. 2. 3. 4. Click from time mask setting. Enter Mask name, e.g. Weekend. Check “Sun” & “Sat” boxes. Select “Start time” and “End time” or “Full day”. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.8 SYSTEM Date/Time, Daylight Saving, SD card and Maintenance settings can be performed on this page. The "System" page has 4 tabs of the [Date/Time] tab, the [Daylight Saving] tab, the [SD card] tab and the [Maintenance] tab. 4.8.
EVS200A/EVS200AW in the status display area. Press Apply to apply the setting changes or Reset to reset without saving the change. Set Time Zone Time Zone: Select a time zone according to the location where the camera is in use. Set Date/Time Manually Date: Click the calendar and pick the date. Press << to go previous year, < to go previous month, > to go next month and >> to go next year. Time: Click on Hour, Minute, Seconds, am/pm; then use up arrow to increase value and down arrow to decrease value.
EVS200A/EVS200AW 4.8.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving. Set the start time to daylight saving time. Set the start week of daylight saving time: 1st / 2nd / 3rd / 4th / Last Set the start date of daylight saving time: Sunday / Monday / Tuesday / Wednesday / Thursday / Friday / Saturday Set the start month of daylight saving time: January / February / March / April / May / June / July / August / September / October / November / December.
EVS200A/EVS200AW “End” time when daylight saving ends. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.8.3 SD Card Setup SD Card Notification: Notification will be made via e-mail when the remaining space of the SD memory card reached the value selected from the following. 50%, 20%, 10%, 5%, 2%, 0% Notes: ‧ When "50%" is selected, e-mail notification will be made each time the remaining space reaches 50%, 20%, 10%, 5%, 2% and 0%.
EVS200A/EVS200AW record event video to SD card. Overwrite: Select ON for overwriting data when SD card memory is full. Select OFF for not overwriting SD card data. Press Apply to apply the setting changes or Reset to reset without saving the change. SD Card Utility The total size and available size of the SD memory card will be displayed. Depending on the state of the SD memory card, the size indications will differ as follows.
EVS200A/EVS200AW 4.8.4 Serial Communication Add Serial Communication setting. -Channel 1 ID: This entry is used to assign channel 1 camera own ID code. -Channel 2 ID: This entry is used to assign channel 2 camera own ID code. -Baud Rate: This field is to set the speed at which is used to transmit instruction or information through the RS485 port on the camera. There are six different speeds, 2400/4800/9600/19200/38400/57600.
EVS200A/EVS200AW 4.8.5 Maintenance Maintenance Server Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reboot button if the unit is not behaving as expected. Restore: The unit is restarted and most current settings are reset to the factory default values by pressing Restore button. The only settings saved are: • • IP setting DDNS setting Default: The Default button should be used with caution.
EVS200A/EVS200AW the Load button. The settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EVS200A/EVS200AW with the latest firmware. Press Browse button to search firmware file. Press Upgrade button to upgrade the firmware. Note 1: Do not disconnect power to the unit during the upgrade. The unit reboots automatically after the upgrade has completed. (1-5 minutes.) 2. During upgrading process, all event recording actions will be stopped.
EVS200A/EVS200AW 5. SPECIFICATIONS VIDEO STREAMING Video Compression Video Resolution Video Quality Frame Rate Video Source H.264/MPEG-4/M-JPEG 4CIF, VGA, CIF, QVGA, QCIF 8 levels adjustable Up to 30fps 1 BNC composite, 1 V p-p / 75Ω NTSC/PAL auto-sense AUDIO Compression Method Operation Mode NETWORK IMA ADPCM (Pulse Code Modulation) 2 way audio Interface 10Base-T/100Base-TX auto-negotiation, RJ-45 socket Support MDI/MDI-X auto crossover function Supported Protocols Bandwidth Control Max.
EVS200A/EVS200AW EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan China Office: Room B-05D-1, KESHI PLAZA, Shangdi Information Industry Base,Haidian TEL: 886-2-26982334 FAX: 886-2-26982380 www.everfocus.com.tw District, Beijing China 100085 TEL: +86-10-62973336/37/38/39 FAX: +86-10-62971423 USA Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. www.everfocus.com.