PRODUCT SPECIFICATION ST-001-B1 User Manual 1
CONTENT FCC Statement...................................................................................................................................3 PRODUCT FEATURES ......................................................................................................................6 PRODUCT SPECIFICATIONS...........................................................................................................7 PIN ASSIGMENT.............................................................................
FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
4.The Third party will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. 5. The Third party will ensure the Module is programmed in the factory with compliant transmit power not exceeding the levels specified in this document. ST-001-B1 requests that the Third party acknowledge its receipt of this document and the above instructions. You may contact EverComm Opto Ltd.
PRODUCT FEATURES Star operation with up to Multiple active piconets with background scan and support for Star mode Does not support frequency hopping, this module uses a fixed frequency transmission method Low power consumption for meeting worldwide energy standards Operate at ISM frequency Band 2.4G Support 1-15 channel,2405-2475MHz Programmable Output Power up to 20dBm 2.4-GHz IEEE 802.15.
Intelligent Lighting Systems PRODUCT SPECIFICATIONS MAIN CHIPSET Texas Instruments CC2538 FUNCTIONAL SPECIFICATIONS 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver Interface UART:4800,9600,19200,38400,115200 12-Bit ADC With 8 Channels and Configurable Resolution Frequency Range 2405MHz – 2475MHz Transmit Output Power Output Power up to < +20dBm Receiver Sensitivity –97 dBm Data Rate 250KHz Antenna Type 2.
PIN ASSIGMENT Pin Pin Define I/O Description 1 GND G Ground 2 VIN I Input Voltage Maxima :+5V±5% Supply module voltage 3-9 GND G Ground 10 PD0 I/O GPIO port D pin 0 11 PA7 I/O 12 PA6 I/O 13 PA5 I/O 14 PA4 I/O 15 GND G Ground 16 GND G Ground 17 PA3 I/O 18 PA2 I/O 19 PA1 GPIO port A pin 7, ADC3 analog input AIN7 GPIO port A pin 6, ADC3 analog input AIN6 GPIO port A pin 5, ADC3 analog input AIN5 GPIO port A pin 4, ADC3 analog input AIN4 GPIO port A pin 3, ADC3 a
22 PC1 I/O GPIO port C pin 1 23 GND 24 PC4 I/O GPIO port C pin 4 25 PC5 I/O GPIO port C pin 5 26 PB0 27 RST 28 PB1 29 PB2 30 PB3 31 PB4 32 PB5 33 Ground I/O I/O I/O GPIO port B pin 0 SYSTEM Reset PIN GPIO port B pin 1 I/O GPIO port B pin 2 I/O GPIO port B pin 3 I/O GPIO port B pin 4 I/O GPIO port B pin 5 GND G Ground 34 +3.
MODULE PINOUT 10
MECHANICAL PCB Thickness:1.2mm Module Thickness:3.
ENVIRONMENTAL OPERATING Operating Temperature: 0 to 50 C (32 to 122 F) Relative Humidity: 5-90% (non-condensing) STORAGE Temperature: -40 to 80 C (-40 to 176 F) Relative Humidity: 5-95% (non-condensing) 12
