SKU # 1001187540, 1001187555 1000026697, 1000026692 Model # AUTOJ100A2, AUTOJ100A3 J100A3, J200A3 USE AND CARE GUIDE SHALLOW WELL JET PUMP Questions, problems, missing parts? Before returning to the store call Everbilt Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-844-241-5521 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this shallow well jet pump.
Table of Contents Table of Contents ............................................................. 2 Performance ..................................................................... 2 Safety Information............................................................ 2 Warranty ............................................................................. 3 Pre-Installation ................................................................. 4 Installation ...........................................................
Safety Information (continued) IMPORTANT: This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris may cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump problems and remedies. IMPORTANT: Ensure the electrical power source is adequate for the requirements of the pump.
Pre-Installation APPLICATION This unit is a single stage jet pump designed for shallow water well applications, where the water level is less than 25 ft. deep. If the water level to the pump is deeper than 25 ft., a convertible jet pump or a deep well submersible pump should be used. A pressure switch pre-set at 30psi “on”, 50psi “off” has been installed on the pump. The pressure switch will automatically turn the pump on and off based on the system pressure.
Pre-Installation (continued) PACKAGE CONTENTS A SKU #1001187540 SKU # 1001187555 Part Description A Pump B Pressure tank SKU #1000026697 SKU # 1000026692 Part Description A Pump SPECIFICATIONS Power supply 115V/230V, 60 HZ., 20/10Amp circuit Liquid temp. range 32°F to 77°F(0°- 25°C) Discharge size 1 in. FNPT SKU # 1001187540:1 in. FNPT SKU # 1000026697, SKU # 1000026692, SKU # 1001187555: 1-1/4 in. FNPT 25 ft. Suction size Water level 5 HOMEDEPOT.
Installation WARNING: ELECTRICAL SAFETY Capacitor voltage may be hazardous. To discharge the motor capacitor, hold the insulated handle screwdriver BY THE HANDLE and short capacitor terminals together. Do not touch the metal screwdriver blade or capacitor terminals. If in doubt, consult a qualified electrician. CAUTION: Do not touch an operating motor. Modern motors are designed to operate at high temperatures.
Installation (continued) WELL POINT (DRIVEN POINT) INSTALLATION Drive the well, using drive couplings and a drive cap. Drive fittings are threaded all the way through and allow the pipe ends to butt against each other so that the driving force of the maul is carried by the pipe and not by the threads. The ordinary fittings found in hardware stores are not threaded all the way through the fitting and can collapse under impact.
Installation (continued) CASED WELL INSTALLATION, 2 IN. ORLARGER CASING Mount the pump as close to the well as possible. Assemble the foot valve, strainer, and well pipe. Make sure that the foot valve works freely. Lower the pipe into the well until the strainer is 5 ft. above the bottom of the well. It should also be at least 10 ft. below the well’s water level while the pump is running in order to prevent the pump from sucking air. Install a sanitary well seal.
Installation(continued) INSTALLATION FOR SURFACE WATER The pump should be installed as close to the water as possible, with the fewest possible fittings (especially elbows) in the suction pipe. The suction pipe should be at least as large as the suction port on the pump. Assemble a foot valve and suction pipe. Make sure that the foot valve works freely. Use Teflon tape on threaded pipe joints. Protect the foot valve assembly from fish, trash, etc, by installing a screen around it.
Discharge Pipe and Pressure Tank Connections PRE-CHARGE TANK CONNECTION Install two tees in the pump discharge port. The pipe size must be at least as large as the discharge port. NOTE: A pre-plumbed pump-on-tank system only requires one tee. Run a pipe or reinforced hose from one arm of the first tee to the port on the pre-charged tank. Connect the other discharge tee to your plumbing system. Check the pre-charge of air in the tank with an ordinary tire gauge.
Discharge Pipe and Pressure Tank Connections (continued) STANDARD TANK CONNECTION Install a tee in the pump discharge port. Run a pipe from the pump discharge port to the inlet port of your tank. The pipe size must be at least as large as the discharge port. Install a tee with reducing bushings in the suction pipe as shown. Install a barbed fitting in the smallest bushing(1/8" NPT).
Pressure Switch Assembly Instructions WARNING: Before wiring the pressure switch, turn off the power source to which you are connecting to avoid potentially life threatening electrical shock. WARNING: It is recommended all electrical work be performed by a licensed electrician. WARNING: When wiring from the power source to the pressure switch, it is recommended that you use either a 14-gauge or 12-gauge cord. To complete the installation, you must connect the power source to the pressure switch.
Priming WARNING: Never run the pump against a closed discharge. To do so can boil water inside the pump, causing hazardous pressure in the unit, risk of explosion and possibly scalding persons handling the pump. CAUTION: Never run the pump dry. Running the pump without water may cause the pump to overheat, damaging the seal and possibly causing burns to persons handling the pump. Fill the pump with water before starting. Remove the priming plug from the priming tee and fill the pump.
Troubleshooting Problem Possible Cause Corrective Action The motor will not run. 1. The disconnect switch is off. 2. The fuse is blown or circuit breaker tripped. 3. Wires at the motor are loose, disconnected, or wired incorrectly. 4. Pressure switch contacts are dirty. 1. Ensure the switch is on. 2. Replace the fuse or reset circuit breaker. 3. DISCONNECT POWER; check and tighten all wiring. 4. DISCONNECT POWER and clean the electrical contacts. The motor runs hot and the overload kicks off. 1.
Troubleshooting (continued) Problem The pump does not deliver water to full capacity. The pump delivers water but does not shut off or the pump cycles too frequently. Possible Cause Corrective Action 1. The water level in the well is lower than 1. A deep well jet will be needed if your well estimated. 2. Steel piping (if used) is corroded or limed, causing excess friction. 3. Piping is too small in size. 4. The well point is packed. 1.
Questions, problems, missing parts? Before returning to the store call Everbilt Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-844-241-5521 HOMEDEPOT.
SKU# 1001 187 540, 1001 187 555 1000 026 697, 1000 026 692 Model# AUTOJ100A2, AUTOJ100A3 J100A3, J200A3 GUÍA DE USO Y DE MANTENIMIENTO BOMBAS TIPO “JET” PARA POZOS POCO PROFUNDOS ¿Preguntas, problemas, piezas que faltan? Antes de devolverla a la tienda, llame a Servicio al Cliente de 8:00 AM a 6:00 pm EST de Lunes a Viernes. 1-844-241-5521 HOMEDEPOT.COM ¡GRACIAS! Nosotros agradecemos la confianza que Usted ha puesto en Everbilt por la compra de esta bomba de sumidero sumergible.
Table Des matières Tubería de Descarga y Conexiones del Tanque de Presión ................................................................................. 26 Instrucciones para Montaje de Interruptor de Presión ................................................................................. 28 CEBADO .............................................................................. 29 Solución de Problemas ................................................... 30 Table Des matières .............................
Información De Seguridad (seguido) CAUTELA: Siga sus códigos de seguridad eléctrica local, especialmente los del Código Eléctrico Nacional (NEC) y en el lugar de trabajo. El Acta de Seguridad y Salud Ocupacional. (OSHA). IMPORTANTE: Asegure que la fuente de electricidad es adecuada para los requisitos que exige la bomba. IMPORTANTE: El motor de la bomba tiene un protector térmico automático de reajuste que se apaga si la bomba se recalienta.
Pre-Montaje Aplicación Esta unidad es una bomba de chorro de una etapa para aplicación con pozos poco profundos. La bomba puede bombear agua donde el agua está ubicada menos de 25 pies (7.62 metros) verticales de la bomba. Si el agua está más profundo que 25 pies (7.62 metros), una bomba de chorro convertible o una bomba sumergible de pozo profundo se debería usar. Un interruptor de presión preprogramado a 30psi “ON” (PRENDIDO) y 50psi “OFF” (APAGADO) se ha instalado en la bomba.
Pre-Montaje (seguido) CONTENIDO DEL PAQUETE A SKU # 1001187540 SKU # 1001187555 Parte Descripción A Bomba B manómetro SKU # 1000026697 SKU # 1000026692 Parte Descripción A Bomba Especificaciones Voltaje 115V, 60 HZ., Circuito de 10/20 Amperios Rango de Temperatura de Líquido 0°C a 25°C (32°F a 77°F) Tamaño de descarga NPT Hembra de 1 pg. SKU # 1001187540: NPT Hembra de 1 pg. SKU # 1000026697, SKU # 1000026692, SKU # 1001187555: NPT Hembra de 1-1/4 pg. 25 pies (7.
Montaje ADVERTENCIA: El voltaje del capacitor puede ser peligroso. Para descargar el capacitor del motor, tome un desatornillador con mango aislado POR EL MANGO y ponga en corto las terminales del capacitor. No toque la superficie de metal del desatornillador ni las terminales del capacitor. Si tiene alguna duda, consulte a un electricista calificado. PRECAUCIÓN: No toque un motor en operación. Los motores modernos están diseñados para operar a temperaturas altas.
Montaje (seguido) Utilice el menor número de conexiones posible (especialmente codos) al conectar la tubería desde el punto del pozo al orificio de succión de la bomba. La tubería de succión debe ser por lo menos del mismo tamaño que el orificio de succión en la bomba (incluya una válvula "check" si su equipo no está equipado con una).
Montaje (seguido) INSTALACION DE POZO RECUBIERTO CON UN RECUBRIMIENTO DE 2" OMAS Monte la bomba tan cerca del pozo como sea posible. Instale la válvula de retención, el filtro y la tubería del pozo. Asegúrese de que la válvula de retención funcione libremente. Baje la tubería hacia el pozo hasta que el filtro se encuentre a cinco pies sobre el fondo del pozo.
Montaje (seguido) Instalacion para agua superficial La bomba se debe instalar lo más cerca del agua que sea posible, con el menor número posible de conexiones (especialmente codos) en la tubería de succión. La tubería de succión debe ser por lo menos del mismo tamaño que el orificio de succión de la bomba. Instale una válvula de retención y la tubería de succión. Asegúrese de que la válvula de retención funcione libremente.
Tubería de Descarga y Conexiones del Tanque de Presión CONEXIÓN PARA TANQUEPRE-CARGADO Instale dos "T"s en el puerto de descarga de la bomba. El tamaño de la bomba debe de ser por lo menos tan grande como el puerto de descarga. NOTA: Un sistema de bomba sobre tanque con la plomería preparada solamente requiere un Te. Instale un tubo o una manguera reforzada desde un brazo de la primera "T" al puerto en el tanque pre-cargado. Conecte el otro Te de descarga a su sistema de plomería.
Tubería de Descarga y Conexiones del Tanque de Presión (seguido) CONEXIÓN PARA TANQUE ESTÁNDAR Instale una "T" en el puerto de descarga de la bomba. Ponga una bomba desde el puerto de descarga al puerto deentrada de su tanque. El tamaño del tubo debe ser por lomenos tan grande como el puerto de descarga. Instale un Te con manguitos reductores en la tubería de aspiración según se ilustra. Instale un accesorio dentado en el manguito más pequeño(1/8" NPT).
Instrucciones para Montaje de Interruptor de Presión ADVERTENCIA: Antes de cablear el interruptor de presión, apague la fuente a que Usted está conectando para evitar un shock eléctrico ADVERTENCIA: Es recomendado que todo trabajo eléctrico sea hecho por un electricista licenciado. ADVERTENCIA: Cuando cablee de la fuente de electricidad al interruptor de presión, es recomendado que Usted use un cable de calibre-14 o calibre-12.
Cebado ADVERTENCIA: No haga la conexión a tierra en una línea de suministro de gas. Nunca ponga a funcionar una bomba hacia una descarga cerrada. Hacerlo puede ocasionar que el agua en el interior de la bomba ebullicione, produciendo una presión peligrosa en la unidad, riesgo de explosión y posibles quemaduras con el agua a la persona que esté manejando la bomba. PRECAUCIÓN: Nunca ponga a funcionar la bomba enseco.
Solución de Problemas PROBLEMA CAUSA(S) PROBABLE(S) ACCIÓN CORRECTIVA El motor no enciende 1. El interruptor de desconexión está apagado 2. El fusible está quemado o el circuito interruptor se abrió 3. Los cables en el motor están sueltos, desconectados o conectados incorrectamente. 4. Los contactos del interruptor de presión están sucios 1. Asegúrese de que el interruptor esté encendido 2. Reemplace el fusible o vuelva a cerrar el circuito interruptor 3.
Solución de Problemas (seguido) PROBLEMA CAUSA(S) PROBABLE(S) ACCIÓN CORRECTIVA La bomba entrega agua pero no seapaga o los ciclos de bombeo son muy frecuentes 1. El interruptor de presión está desajustado o los contactos están soldados juntos 2. Se dejaron las llaves abiertas 3. El venturi, la boquilla o el impulsor están tapados 4. El nivel de agua en el pozo profundo es menor de que se calculó 5. El tanque de presión estándar está tapado por agua y no tiene amortiguador de aire 1.
¿Preguntas, problemas, piezas que faltan? Antes de devolverla a la tienda, llame a Servicio al Cliente de 8:00 AM a 6:00 pm EST de Lunes a Viernes. 1-844-241-5521 HOMEDEPOT.