User manual ReliaGATE 10-14 Multi-service IoT Edge Gateway - NXP i.MX8, LTE Cat 1 Rev.
Trademarks All trademarks, registered trademarks, logos, trade names, products names contained in this document are the property of their respective owners. Intended audience of this document This document is intended for system integrators: skilled persons with a thorough knowledge in linking together, physically or functionally, different computing systems and software applications to operate as a coordinated whole in compliance with the applicable regulations.
ReliaGATE 10-14 User manual Rev. 0-10 How to get started HOW TO GET STARTED To get started with the ReliaGATE 10-14, follow these steps: 1. Read carefully and understand the instructions and warnings contained in this manual. To lower the risk of personal injury, electric shock, fire, or damage to equipment, observe the instructions and warnings contained in this manual. For more information see: "Safety instructions" on page 9.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 Contents CONTENTS Trademarks Intended audience of this document Revision history 2 2 2 How to get started 3 Contents 5 1 Safety instructions 1.1 Warning messages 1.1.1 Warning messages for harm to persons 1.1.2 Warning messages for damage to property 1.2 Warning: power supply safety 1.3 Caution: wireless safety 1.4 Caution: product's surfaces may become hot 9 9 9 10 10 10 11 2 Consignes de securite 2.1 Messages d’avertissement 2.1.
Contents ReliaGATE 10-14 User manual Rev. 0-10 7.2.2 FCC Class B Digital Device Notice 7.2.3 FCC restrictions on 5 GHz Wi-Fi usage 7.2.4 ISED Canada Regulatory Notices 7.2.5 ISED Class B Digital Device Notice 7.2.6 Responsible parties: Canadian Representative contact information 7.2.7 RF Radiation Exposure Statement 7.2.8 Labeling Information 7.3 Antennas list 7.4 REACH compliance 32 33 34 34 34 34 35 35 35 8 Interfaces overview 8.1 LED Indicators overview 8.2 Top Side Interfaces overview 8.
ReliaGATE 10-14 User manual Rev. 0-10 9.11.2 The RTC backup supercap 9.12 Case Intrusion 9.13 TPM 9.14 Watchdog Contents 58 58 58 58 10 The Software 10.1 The Linux OS Distribution 10.2 Ensure power supply during installation and update 10.3 Docker 10.4 Microsoft IoT Edge 10.5 System Firewall 10.6 Partition layout 59 59 59 59 59 59 60 11 How to access the Administration Console 11.1 Default credentials 11.2 Login Messages 11.3 How to login via the Serial Console 11.
Contents ReliaGATE 10-14 User manual Rev. 0-10 15 Power supply. How to turn ON/OFF and reset the product 15.1 Power supply specifications 15.2 Power IN connector specifications 15.3 How to supply power and turn ON the product 15.4 How to turn OFF the product 15.5 How to reduce the power consumption of the product 15.6 How to hardware reset the product 83 83 83 84 85 85 85 16 How to maintain the product 16.1 How to safely remove the power supply 16.2 How to verify the installation of the product 16.
ReliaGATE 10-14 User manual Rev. 0-10 1 1 Safety instructions SAFETY INSTRUCTIONS IMPORTANT: Read carefully and understand the instructions and warnings contained in this document before installing / using the product. Keep this document for future reference. To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the instructions and warnings contained in this document.
1 Safety instructions 1.1.2 ReliaGATE 10-14 User manual Rev. 0-10 Warning messages for damage to property To indicate potential risks of damage to the supported product (or to other property), the following message is used: NOTICE Sign (if necessary) 1.
ReliaGATE 10-14 User manual Rev. 0-10 1.4 1 Safety instructions Caution: product's surfaces may become hot Depending on the operating environment temperature, product's surfaces may become hot, creating a burn hazard. Always allow the product's surfaces to cool before touching them.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 2 2 Consignes de securite CONSIGNES DE SECURITE IMPORTANT: Lire attentivement et bien respecter les instructions et les avertissements contenus dans ce document avant d'installer / d'utiliser le produit. Conserver ce document pour s'y référer à l'avenir. Pour éviter les risques de blessures, de choc électrique, d'incendie ou de détérioration du matériel, bien suivre les instructions et les avertissements contenus dans ce document.
2 Consignes de securite 2.1.2 ReliaGATE 10-14 User manual Rev. 0-10 Messages d’avertissement relatifs aux dommages matériels Pour signaler les risques potentiels de détérioration du produit (ou des produits annexes), le message suivant est utilisé: AVIS Signal (si besoin) 2.
ReliaGATE 10-14 User manual Rev. 0-10 2.4 2 Consignes de securite Attention: les surfaces du produit peuvent devenir chaudes Selon la température ambiante lors de l’utilisation, les surfaces du produit peuvent devenir brûlantes, engendrant un risque de brûlure. Laisser toujours les surfaces du produit refroidir avant de les toucher.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 3 How to receive technical assistance 3 HOW TO RECEIVE TECHNICAL ASSISTANCE 3.1 How to ask for technical support To ask for technical support, complete the following steps 1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/ 2. Submit a support request 3. Wait for the reply from the Eurotech Technical Support with the information you required 3.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 4 Comment obtenir une assistance technique 4 COMMENT OBTENIR UNE ASSISTANCE TECHNIQUE 4.1 Comment contacter le support technique Pour demander un support technique, procéder comme suit: 1. Se connecter au Support Eurotech sur: https://support.eurotech.com/ 2. Envoyer une demande d’assistance 3. Attendre la réponse de l'équipe de support avec les informations requises 4.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 5 CONVENTIONS USED 5.1 Conventions for signal names 5.2 Convention Description GND Ground # Active low signal + Positive signal; Positive signal in differential pair - Negative signal; Negative signal in differential pair 3.3 3.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 6 Product overview 6 PRODUCT OVERVIEW 6.1 Product description The ReliaGATE 10-14 is a Multi-service IoT Gateway that has been designed to deliver LTE connectivity (with 3G and 2G1 fallback) to industrial and lightly rugged applications. Based on the i.MX 8M Mini Quad Cortex-A53 1.
6 Product overview 6.2 ReliaGATE 10-14 User manual Rev. 0-10 Intended use and not allowed uses of the product The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). 6.2.
ReliaGATE 10-14 User manual Rev. 0-10 6.3 6 Product overview Technical specifications The ReliaGATE 10-14 family is available in several -XY versions, for example: ReliaGATE 10-14-35 (where: X = 3, Y = 5). The technical specifications are the following, according to the respective versions: Specifications Description according to -XY versions -32 Processor -35 -36 -37 CPU i.MX 8M Mini Quad Cortex-A53 1.
6 Product overview ReliaGATE 10-14 User manual Rev.
ReliaGATE 10-14 User manual Rev. 0-10 6.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 7 7 Regulatory information (preliminary information) REGULATORY INFORMATION (PRELIMINARY INFORMATION) This section provides regulatory information for the ReliaGATE 10-14 (hereafter referred to as "this "product"). Upon request, Eurotech can provide the product Declaration of Conformity. For details and more information contact the Eurotech Technical Support (see "How to receive technical assistance" on page 17).
7 Regulatory information (preliminary information) 7.1.5 ReliaGATE 10-14 User manual Rev. 0-10 RoHS 3 compliance This product has been manufactured in compliance with the following Directives: l Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
ReliaGATE 10-14 User manual Rev. 0-10 7.1.6.
7 Regulatory information (preliminary information) 7.2 FCC/ISED Regulatory Notices 7.2.1 FCC marking ReliaGATE 10-14 User manual Rev. 0-10 Some versions of this product are FCC marked (for more information see "Technical specifications" on page 25). They comply with the regulatory information reported in the following sections. Eurotech is not responsible for the use of the product together with equipment (for example: power supplies, personal computers, etc.
ReliaGATE 10-14 User manual Rev. 0-10 l l l l 7.2.3 7 Regulatory information (preliminary information) Réorienter ou déplacer l'antenne de réception Augmenter la distance entre le produit et le récepteur Brancher l'appareil sur une prise de courant différente de celle à laquelle le récepteur est raccordé Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide.
7 Regulatory information (preliminary information) 7.2.4 ReliaGATE 10-14 User manual Rev. 0-10 ISED Canada Regulatory Notices This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ReliaGATE 10-14 User manual Rev. 0-10 7 Regulatory information (preliminary information) autre antenne ou un autre émetteur, sauf en conformité avec les procédures du produit multi-émetteur de la FCC. 7.2.8 Labeling Information The following information is stated on the product label(s): Les informations suivantes sont indiquées sur l'étiquette (les étiquettes) du produit: l Contains FCC ID: UKMMRG1014 l Contains IC: 21442-MRG1014 l Contains FCC ID: RI7LE910CXNF l Contains IC: 5131A-LE910CXNF 7.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 8 Interfaces overview 8 INTERFACES OVERVIEW 8.1 LED Indicators overview The LED Indicators are as follows: Figure 8.
8 Interfaces overview 8.2 ReliaGATE 10-14 User manual Rev. 0-10 Top Side Interfaces overview The Top Side Interfaces are as follows: Figure 8.2 - Top Side Interfaces layout Ref# Description 1 COM 0/1 connector 2 Digital IN/OUT, Analog IN connector 3 Antenna connector for 2.
ReliaGATE 10-14 User manual Rev. 0-10 8.3 8 Interfaces overview Bottom Side Interfaces overview The Bottom Side Interfaces are as follows: Figure 8.3 - Bottom Side Interfaces layout Ref# Description 1 Power IN connector 2 DisplayPort 3 USB0 connector 4 USB1 connector 5 Ethernet ETH0 connector 6 Ethernet ETH1 connector Table 8.
8 Interfaces overview 8.4 ReliaGATE 10-14 User manual Rev. 0-10 Right Side Interfaces overview The Right Side Interface is as follows: Figure 8.4 - Right Side Interfaces layout Ref# Description 1 Expansion connector Table 8.
ReliaGATE 10-14 User manual Rev. 0-10 8.5 8 Interfaces overview Service Panel overview (Left Side) The Service Panel is placed on the Left Side and includes the Service Interfaces. 8.5.1 Ref# Description 1 Service Panel: includes the Service Interfaces Anti-Tamper Function The ReliaGATE 10-14 is equipped with anti-tamper detection: when the Service Panel (or the case) is opened, the intrusion event is timestamped and recorded by the RTC.
8 Interfaces overview 8.5.2 ReliaGATE 10-14 User manual Rev. 0-10 How to remove the Service Panel cover NOTICE The IP grade is not maintained when the Service Panel cover is removed. Do not use the product for extended periods of time with the Service Panel cover removed, otherwise dust and other particulates may enter the system. If it is necessary to have extended access to the Service Panel, take appropriate precautions to stop any particulates from entering.
ReliaGATE 10-14 User manual Rev. 0-10 8.5.3 8 Interfaces overview Service Interfaces overview The Interfaces available in the Service Panel are as follows: Figure 8.
8 Interfaces overview 8.5.3.1 ReliaGATE 10-14 User manual Rev. 0-10 DIP-switches meaning Default DIP switch configuration is OFF; this means no resistors inserted.
ReliaGATE 10-14 User manual Rev. 0-10 8.5.4 8 Interfaces overview MicroSD and MiniSIM card holders Both the MicroSD card holder and the dual MiniSIM cards holder are placed on the top side of the circuit board in the Service Panel: l The MicroSD card holder is a push-push type. The MicroSD card holder allows you to insert a MicroSD card for additional data storage. l The dual MiniSIM cards holder is a push-pull type. Insert SIM1 in the top holder.
8 Interfaces overview 8.6 ReliaGATE 10-14 User manual Rev. 0-10 Rear Side overview The Rear Side is as follows: Figure 8.7 - Rear Side layout Ref# Description 1 Product Label position 2 DIN Rail Mounting Clip 3 Earth connection terminal Table 8.
ReliaGATE 10-14 User manual Rev. 0-10 9 Interfaces in detail 9 INTERFACES IN DETAIL 9.1 Wi-Fi and Bluetooth The ReliaGATE 10-14 integrates a dual-band (2.4 & 5GHz), 1-stream (1x1) 802.11ac Wi-Fi and Bluetooth (BT/BLE4.2) module. The antenna connector is placed on the top side. 9.1.1 Wi-Fi and Bluetooth specifications Feature RF Spec Description l l Interfaces l l l l l l Support Data Rate l l l l l Transmission Power l l l l l l l 9.1.2 Wi-Fi - 802.11 a/b/g/n/ac (2.
9 Interfaces in detail 9.2 ReliaGATE 10-14 User manual Rev.
ReliaGATE 10-14 User manual Rev. 0-10 9.2.3 9.2.4 Second cellular antenna requirements (for antenna diversity) Feature Value Frequency range Depending on the frequency band(s) provided by the network operator Supported Bands See "Supported RF bands" on the previous page Impedance 50 Ohm VSWR recommended ≤ 2:1 (limit to fulfil all regulatory requirements) Cellular antennas - Installation guidelines l l 9.2.
9 Interfaces in detail 9.2.7 GNSS antenna - Installation guidelines l l 9.2.8 ReliaGATE 10-14 User manual Rev. 0-10 The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The antenna must not be installed inside metal cases. GNSS antenna requirements The ReliaGATE 10-14 supports an active antenna. It is recommended to use antennas as follow: l An external active antenna (17dB typ.
ReliaGATE 10-14 User manual Rev. 0-10 9.3 9 Interfaces in detail Digital IN/OUT and Analog IN The ReliaGATE 10-14 provides the following interfaces on the top side: l 4x Digital Inputs Optoisolated, l 2x Digital Outputs Optoisolated, l 2x 11-bit Analog Inputs Isolated 9.3.1 Digital IN/OUT and Analog IN specifications Digital inputs specifications: l Optoisolation 1.
9 Interfaces in detail 9.4 ReliaGATE 10-14 User manual Rev. 0-10 COM0 and COM 1 The ReliaGATE 10-14 provides 2x RS-232/422/485 protected and isolated serial ports on the top side. 9.4.1 COM0 and COM 1 connector specifications Connector Layout: Connector Pinout in RS-232 mode: Pin # Connector Specifications: l DMC 1,5/5-G1F-3,5-LR Header l Gender: Male l Type: 5*2-pin; 3.5 mm pitch Mating Connector Specifications: l DFMC 1,5/ 5-STF-3,5 Housing l Gender: Female l Type: 8*2-pin; 3.
ReliaGATE 10-14 User manual Rev. 0-10 9.5 9 Interfaces in detail DisplayPort The ReliaGATE 10-14 provides a DisplayPort on the bottom side. 9.5.
9 Interfaces in detail 9.6 ReliaGATE 10-14 User manual Rev. 0-10 USB 0 and USB 1 The ReliaGATE 10-14 provides 2x Host 2.0 USB ports (Noise and Surge Protected) for general purpose applications on the bottom side: l USB 0; max load: 500 mA l USB 1; max load: 500 mA 9.6.
ReliaGATE 10-14 User manual Rev. 0-10 9.7 9 Interfaces in detail ETH 0 and ETH 1 The ReliaGATE 10-14 provides 2x 10/100/1000 Mbps Ethernet ports: l ETH 0 l ETH 1 The Ethernet connectors are available on the bottom side. 9.7.1 9.7.2 Ethernet specifications Feature Description Network Standard 10BASE-Te/100BASE-Tx/1000 BASE-T IEEE 802.
9 Interfaces in detail 9.8 ReliaGATE 10-14 User manual Rev. 0-10 Expansion The ReliaGATE 10-14 provides, on the right side, an expansion connector with the following interfaces: l USB interface l I2S Audio interface l SPI interface l Additional GPIO signals l I2C interface For more information see: l "Right Side Interfaces overview" on page 40 9.8.1 Expansion connector specifications Connector Layout: Connector Specifications: l 2mm dual row R/A header l Gender: Female l Type: 12*2-pin; 2.
ReliaGATE 10-14 User manual Rev. 0-10 9.9 9 Interfaces in detail TTL Serial Console The ReliaGATE 10-14 provides a 3.3 V TTL compatible Serial console in the Service Panel. The voltage levels are as follows: l Logic 1 (Hi): 2.0 to 3.3 V l Logic 0 (Low): 0 to 0.8 V 9.9.1 TTL Serial Console connector specifications Connector Layout: Connector Specifications: l Shrouded header l Gender: Male l Type: Pitch 1.
9 Interfaces in detail 9.11 ReliaGATE 10-14 User manual Rev. 0-10 RTC (Real Time Clock) The ReliaGATE 10-14 includes the following two RTC (Real Time Clocks) devices: RTC device /dev/rtc0 Description User available l External (I2C-based RTC device) Default RTC used by Linux Accuracy: 25 minutes per year (at 25 °C) l Internal (in the CPU SoC) Reserved l l /dev/rtc1 9.11.
ReliaGATE 10-14 User manual Rev. 0-10 10 THE SOFTWARE 10.1 The Linux OS Distribution 10 The Software Eurotech provides a Linux distribution based on a Yocto framework, www.yoctoproject.org, as well as an SDK for application development. For more information see: www.yoctoproject.org/documentation. 10.
10 The Software ReliaGATE 10-14 User manual Rev. 0-10 To disable the system firewall service, complete the following steps: 1. Enter the command systemctl disable iptables 2. Reboot the ReliaGATE 10-14 for the setting to take effect. NOTICE Running a system without a firewall is not recommended for production systems. 10.6 Partition layout The partition layout is as follows: 60 / 90 Partition File System Size (approximately) Description 1 FAT 130 MB Boot Partition.
ReliaGATE 10-14 User manual Rev. 0-10 11 11 How to access the Administration Console HOW TO ACCESS THE ADMINISTRATION CONSOLE This section describes how to access the ReliaGATE 10-14 Linux Operating System by logging into the Administration Console. To login to the Administration Console, use one of the following methods: l Direct login via Console Port l Remote login via Secure Shell (SSH) 11.
11 How to access the Administration Console 11.4 ReliaGATE 10-14 User manual Rev. 0-10 How to login via Secure Shell (SSH) The default (out-of-the-box) network configuration of the ReliaGATE 10-14 is as follows: l eth0 o Status: Enabled for LAN o Configure: Manually (Static IP) o IP Address: 172.16.0.1 o Subnet Mask: 255.255.255.0 o DHCP Server Enabled l eth1 o Status: Enabled for WAN o Configure: DHCP (DHCP client) l wlan0 o Status: Disabled 11.4.
ReliaGATE 10-14 User manual Rev. 0-10 12 12 How to use the interfaces in Linux HOW TO USE THE INTERFACES IN LINUX Interface availability depends on product version. 12.
12 How to use the interfaces in Linux 12.2 ReliaGATE 10-14 User manual Rev. 0-10 How to use the GPIOs: the GPIO Utility The ReliaGATE 10-14 includes the gpio_utility which provides a more convenient way to drive many of the GPIO functions from the command line: gpio_utility pin_name function pin_name It is the required GPIO line in the format gpioN or gpioBank_Pin.
ReliaGATE 10-14 User manual Rev. 0-10 12.4 12 How to use the interfaces in Linux How to use the Digital I/Os The ReliaGATE 10-14 includes 4 opto-isolated inputs and 2 opto-isolated outputs. These IOs are provided by GPIO lines which are available through the sysfs interface.
12 How to use the interfaces in Linux 12.5 ReliaGATE 10-14 User manual Rev. 0-10 Analog Inputs The ReliaGATE 10-14 includes two analog-to-digital converters (ADCs) which are available for use in application programs. The two ADC inputs are isolated from the ReliaGATE 10-14 power supply but share a common ground with each other and with the serial ports. Each channel uses a 12-bit differential converter with the -ve input tied to ground giving an 11-bit input resolution.
ReliaGATE 10-14 User manual Rev. 0-10 12.6 12 How to use the interfaces in Linux How to use the Serial ports The ReliaGATE 10-14 includes two serial ports which are available for use by application programs. Each port may be configured for RS-232, RS-422 or RS-485 operation, and is driven with standard Linux serial port drivers.
12 How to use the interfaces in Linux 12.6.2.1 ReliaGATE 10-14 User manual Rev.
ReliaGATE 10-14 User manual Rev. 0-10 12.6.2.2 12 How to use the interfaces in Linux Configuring the COM port mode from an application program (using the Eurotech set serial mode API) The SDK for the REGATE-10-14 includes a library that allows the mode of the serial port to be controlled directly from a C or C++ application. To use this library, complete the following steps: 1. Include the following header in the application source file #include 2.
12 How to use the interfaces in Linux ReliaGATE 10-14 User manual Rev. 0-10 const char * _eth_SerialModeName(int mode) mode: Integer representing the mode Returns a zero terminated string describing the given mode The example below set COM1 to RS-422 with terminators off then transmits ‘hello’: #include #include #include #include #include #include int main(int argc, char *argv[]) { int fd; struct _eth_serial_mode mode; mode.
ReliaGATE 10-14 User manual Rev. 0-10 12.7 12 How to use the interfaces in Linux How to use the Internal Cellular Modem The ReliaGATE 10-14 supports the Telit LE910C1family of LTE cellular modems: Product version Modem variant Technology -35 Telit LE910C1-NF - North America LTE Cat 1 3G Fallback -36 Telit LE910C1-EU - Europe LTE Cat 1 2G/3G Fallback -37 Telit LE910C1-AP - Japan LTE Cat 1 3G Fallback The modem initialization is handled by a systemd service setup-modem.
12 How to use the interfaces in Linux 12.7.2.1 ReliaGATE 10-14 User manual Rev. 0-10 How to select the AT&T firmware To select the AT&T firmware, use the following command: telit-he910 chat ‘AT#FWSWITCH=0,1’ 12.7.2.2 How to select the Verizon firmware To select the Verizon firmware, use the following command: telit-he910 chat ‘AT#FWSWITCH=1,1’ 12.7.
ReliaGATE 10-14 User manual Rev. 0-10 12 How to use the interfaces in Linux 12.10 The Ignition Key The ReliaGATE 10-14 includes an ignition monitoring circuit which can be used in battery-operated applications. Whilst the ignition input is low, the ReliaGATE 10-14 is powered OFF and will not drain the battery.
12 How to use the interfaces in Linux 12.10.1 ReliaGATE 10-14 User manual Rev. 0-10 Ignition monitoring service The ignition monitoring service calls a script when a change is detected. The default script, located in /usr/bin/ignition_script.sh, initiates a controlled shutdown but this can be changed as required.
ReliaGATE 10-14 User manual Rev. 0-10 12 How to use the interfaces in Linux To disable the system service, enter the following commands: systemctl disable tampermon systemctl stop tampermon The service monitors the tamper detect and calls an action script each time a new event is detected. The action script is located in /usr/bin/tamper_script.sh The default script issues a warning message to all users but that can be modified to suite different situations.
12 How to use the interfaces in Linux ReliaGATE 10-14 User manual Rev. 0-10 12.12 How to output Accelerometer and Gyroscope values The ReliaGATE 10-14 includes a 3D digital accelerometer / 3D digital gyroscope: l The accelerometer is exposed as cat/sys/bus/iio/devices/iio\:device2 l The gyroscope is exposed as cat /sys/bus/iio/devices/iio\:device3 To output the three-dimensional values for the accelerometer, use the following commands: watch –n 1 cat /sys/bus/iio/devices/iio\:device2/in_accel_x_raw watch
ReliaGATE 10-14 User manual Rev. 0-10 12 How to use the interfaces in Linux 12.15 How to use the Watchdog The ReliaGATE 10-14 uses the processor’s internal watchdog to reset the system if the software stops responding. Once triggered, the watchdog must be written to within a configurable timeout period to prevent the system reset. The watchdog appears at /dev/watchdog. Use the wdctl utility to change the watchdog timeout.
12 How to use the interfaces in Linux ReliaGATE 10-14 User manual Rev. 0-10 12.17 User-programmable pushbutton: factory restore The ReliaGATE 10-14 features a user-programmable pushbutton that by default activates a factory restore functionality. This functionality restores the ReliaGATE 10-14 from a failed state. NOTICE The restore operation erases all user data and configuration: use it with caution. 12.17.
ReliaGATE 10-14 User manual Rev. 0-10 13 MECHANICAL SPECIFICATIONS 13.1 Product mechanical dimensions 13 Mechanical specifications The product electronics are housed in an aluminum alloy enclosure having the following dimensions: 107 (L) x 85 (W) x 46 (H); mm - Antennas Connectors and Mounting Bracket excluded. All dimensions are in millimeters.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 14 14 How to install the product HOW TO INSTALL THE PRODUCT The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). NOTICE Always use the Earth connection terminal to connect the ReliaGATE 10-14 to an earth point in the installation.
14 How to install the product 14.1 ReliaGATE 10-14 User manual Rev. 0-10 How to install the product on a DIN Rail Prerequisite: Make sure that the DIN rail is placed horizontally. To install the product on a horizontal DIN rail, complete the following steps: 1. Position the product so that the lower side of the mounting bracket hooks on the lower edge of the DIN rail, see step 1 2.
ReliaGATE 10-14 User manual Rev. 0-10 15 15 Power supply. How to turn ON/OFF and reset the product POWER SUPPLY. HOW TO TURN ON/OFF AND RESET THE PRODUCT This product is not provided with any ON/OFF switch. The Power IN connector is the disconnecting means from the power supply network. 15.1 15.
15 Power supply. How to turn ON/OFF and reset the product 15.3 ReliaGATE 10-14 User manual Rev. 0-10 How to supply power and turn ON the product WARNING ELECTRIC SHOCK HAZARD Failure to supply power correctly or to follow all operating instructions correctly, may create an electric shock hazard, which could result in personal injury or loss of life, and / or damage the equipment or other property. To avoid injuries and safely supply power to the product, complete the following steps: 1.
ReliaGATE 10-14 User manual Rev. 0-10 15 Power supply. How to turn ON/OFF and reset the product 7. Connect Pin 3 (Key Signal) to "Power IN +". The ReliaGATE 10-14 automatically turns ON and the LED 6 (POWER) turns ON NOTICE When connecting Pin 3 to "Power IN +", keep it connected for at least 10 seconds. If you disconnect "Power VIN +" from the Pin 3 before 10 seconds have passed, the startup procedure will not be completed correctly and an immediate and unsafe power down will occur. 8.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev. 0-10 16 16 How to maintain the product HOW TO MAINTAIN THE PRODUCT Periodically inspect the product to verify its integrity and to ensure proper operation. To maintain the product, complete the following steps: 1. Carefully read and understand the instructions contained in the section "Safety instructions" on page 9 2. Safely remove the power supply 3. Verify the installation of the product 4. Clean the product 16.
(This page has been intentionally left blank)
ReliaGATE 10-14 User manual Rev.
EUROTECH.COM HEADQUARTERS Via Fratelli Solari, 3/a 33020 Amaro (UD) - Italy Tel: +39 0433.485.411 Fax: +39 0433.485.499 Email: welcome@eurotech.com Web: www.eurotech.com For your Eurotech local contact refer to: eurotech.com/contacts For the Eurotech Global Support Centre refer to: support.eurotech.com For the Eurotech Download Area refer to: eurotech.
